I am going to part this truck out

Two things that im keeping are the fuel injection As well as the serp belt setup

The current setup is a 305/Th375 The motor runs funny could be blown headgasket i will soon determine what the problem is The trans works great it is non electronic it has an electric speedo but a cable off an older setup could be put in

Id take 150 for the trans They are good for putting in half tons because there a 400 with a th350 output shaft so you dont need a 30 dollar conversion u joint.

Its missing the drivers door glass , has an idiot light dash , Working Am/Fm
Im uncertain of the rearend ratio its high though.

Let me know if any parts i listed are needed or any i didnt fuel pump gas tank etc.



If anyone wants some parts off of it let me know and ill name a price for them
When i get the fuel injection off and brackets ill inventory everyything and post prices

Here is a pic of the truck http://mysite.verizon.net/res6o8ny/pics/Picture211.jpg

TTT Tranmission Is No Longer Available Pass Fender has Dings Hood Is Good ,

Asking 75 For the Hood 75 For the Passenger Fender . 275 gets the whole front clip grille core support evap coil everything.

how much for the hood? is the dash any good?

The Hood Is in really good shape Im going to give it a bodymans lookin over tommorow But im confident thats a good hood Id take 75 For it

By Dash do you mean the padding or the inst cluster? I may keep the dash pad its not that great anyway . THe instrument cluster is an idiot light setup.

need aq rearend with 373 six lugs if you have it

how did it look after the bodymans lookin over? 75.00 is a good price. Now... how to get it to Houston without costing more than 50 bucks. Coming down anytime soon? I just got back from Temple but I wasn't in a suitable transporter... I don't think the company would like me strapping it to the top of their Rodeo.

by Dash i meant the cap. I don't even know if they were the same in 92.

I still havent been able to reach the other guy that wanted the hood. Its In very good shape I belive alot of people use greyhound to ship large items Im not going to houston anytime soon .. at least not that i know of.

Let me know what you decide Im going to try to get some pics my usb ports quit working so i cant upload pics onto this computer so im gonna try to get a friend to upload them and email them to me. Im going to try to have posted on here tommorow.

let me know on the other guy... I'll take it if he doesn't. I have family up there so I can have them pick it up for me. I won't be able to make the trip up until around the 21st

Hood Is Sold...

Are the seat belt covers intact? I'm looking for the pieces that cover the bolt on the b-pillar. They get unclipped from the bottom, then the bolt has to be removed from the pillar to remove the piece that holds it in place. Most people have broken the top off trying to get them off... and that's what's broken on mine :(

The ones i have are blue they are in good shape If i can get them off without breakin them wich im pretty sure i can 25 shipped.

Passenger Door Decent 85$ Drivers Fender Good Shape 65$ Pass fender Not too good but would make a smooth one with some bodywork 30$

Gas Door In good shape 30$

Passenger Door Decent 85$ Drivers Fender Good Shape 65$ Pass fender Not too good but would make a smooth one with some bodywork 30$

Gas Door In good shape 30$

Got the hood today....Looked dern good! Thanks alot.


Is that front bumper dented? I should've thought about that before, but I could always get my stepdad to come get it and hold on to it for me...

Thanks,
D

yea its dented

Sorry for the short reply yesterday My keyboard was caddywhompassed and i had to copy and paste that litlte reply..

Glad to hear your happy with the hood. I was looking at truckin the other day and they had smooth bumpers for painting for like 59 bucks the mag was a few years old but surely the price hasnt gone up that much.

How bout the steering column? is it tilt? floor shift? How much?

non tilt colum shift

Seat Belt Bolt Covers Pending/SOLD

The Seat Belt Bolt covers Are Still For Sale And Boxed Up ready To SHip 15$ shipped.
And they are Blue.

how much for the rest of the front clip?

How much for the rest of the front clip? Looking to get my '96 back together and in working order.

Sorry for the slow reply didnt have a keyboard untill today..

If you still need the clip i would take 250 for it all grille core support evap coil both fenders lights bezels all that good stuff.

But i dont know how you would get it to wisconsin I imagine all the stuff would ship ups if it was taken apart but i think it would be costly.


Let me know either way .

whats the seat like in it. how much would you want for it. thanks, Steve

You wouldnt want it.. most of the intereior is pretty messed up and worn . Some panels are good like speaker grilles . the dash pad ,

Everything else is pretty much worn out from toting around road department workers.

Parts Still For Sale You need it name it This truck is going to be tottaly stripped down to nothing all chassis parts disc brakes rearend spring you name it .

Trans if for sale again Last guy Local Not a board member Was a deatbeat so its for sale BTW It has an electric speedo.


Windsheild Washer Resivoir & pump Works Tested. 30 Shipped , This would be a good piece to adapt into an older truck Since the pump is in the tank.

Overflow tank Missing Cap Dirty .. 10 Plus Shipping

Charcoal Can ? 5$

Headlight Harness The Wire Loom Is Cracking But Otherwise In Good Shape 40$

Grille Good Shape 45$

Headlight Buckets 30 And Thats The Pair

Wiper Motor 30$

Fuel Tank No Leaks W/ Fuel Pump 75$ Local Pickup ONLY.

DriveShaft Truck Had Th375 55$ Length " Coming Soon"



More Parts/Prices/Descriptions/ Coming Soon At the moment i cannot upload pics but as soon as the new cord for my camera arrives from ebay i will be happy to

Please Pm With Any Questions On Mentioned Parts Or Something You May Need Not Mentioned.



Once again My Local Zip Is 75474

Windshield waser pump SOLD>..

Pair Of Hood Hinges With Bolts that attach to the truck 35$ Thats 4 the pair + Shipping.

Cowling Plastic With Screws and end pieces They have white overspray on them but it would prolly remove with thinner.
40$ + Shipping

ABS Controller? Black box With Valve 45$ + Shipping

Power brake booster With Master Cylinder 65$ + Shipping

Instrument Cluster Shows 275K Miles Its Warning Lights Speedo & Gas Gauge 40$ + Shipping Has PRND21 Indicator But needs repair ? the little cable isnt attached.

Horn 15$ , Windshield wiper Under Cowl Setup With Both Shafts and all still attached .. 35$

Automatic Shifter Linkage From Colum To Trans Including Trans Bracket and adjustment bracket for the colum 40$


More to come as items are removed/Inspected Pics coming soon.

Driveshaft Length Is 68 1/2 inches from u joint trunion to u joint trunion .

Blue Seat Belts Could be Used to convert 67-72 to shoulder 50$ thats the full set Im not sure about the middle belt it may be under the seat i havent pulled them yet.

Blue Glovebox Door 25$ Blue Instrument Cluster Surround Pad 25$ Blue Non Casset Player Center Dash Piece 25$ Blue AshTray Assembly all intact 30$

Automatic Transmission Crossmember 45$

Rear Speaker Grilles 25$ Blue..

BTW the windshield wiper motor is only two speed No delay.

Inner Fenders 25$ Each

Core Support 65$

Cab Has hole where vhf antenna was for highway department otherwise in good shape 200$ I can weld hole up upon request.

Emergency Brake Pedal Setup 35$
Brake Pedal 25$ For Auto..

Gas Pedal Assembly W Cable 45$ Cable Seperatly 20$ Gas Pedal Assembly Minus Cable 30$

A/C Controls W Black Buttons Works 25$

Here are some More pics Of the parts

Few more O yeah Cheap Mirrors Came off 89 but are autozone specials
25$Shipped

what about the front discs, spindles, hubs, calipers, all that stuff??? Would also need the tie rods. How much? I can come get the stuff if it's in DFW.
Thanks

The tierods may have wear on them it had some slack Id give you the entire front end cut off the frame for 125 You pick it up .. Im located in Quinlan 75474 Do a mapsco and see if you would want to pick it up Its around 68 miles east of dallas.

They are 6 lug correct?

Nope its 5 on 5 Its not a light duty 2500 Its a half ton.

****, I'll think about that

Few more pics added Will Take 40$ For the evap coils and all hardware that atttachs it It looks ruff but system had freon in it still so no leaks.

Man, I could use a d/s fender and door

D/S Fender and D/s Door pics Coming Up. Is there a greyhound Bus Depot Around You? Thats the only way i know of to ship large items such as doors. The fender isnt al that heavy it should go ups no prob but the door is another story.

The door is a little whomperjawed in the two pics of close up . and the inerts dont go with it

Few Mo

How much for the d/s door (striped, I could really only use the skin) and fender. Do you inbound/outbound freight at work. I can send an LTL carrier if you can put the stuff on a skid.

I had been asking 65$ for the fender and 70 for the door but if you want both 150$

By Skid Do you mean pallet? Im not certain as to where i could take it A Place i used to work at has yellow friend pick stuff up daily but i doubt they would let me send anything out their dock.

Thanks for trying

Greyhound ships large items. Is there a bus depot near you?

Yes, but it will cost twice as much to ship. I'll just keep searching the scrap yards.

I heard there is a place in greenville called Tex Pack Im going to try to get ahold of them and see details What Carrier would you be using.?

Let me know some details .. and whether or not you want me to check into it I just heard about this place today.

does it still have the tailgate? if it does, i need the handle, the handle surround, the rods to the catches, the catches, and both trunions. how much for all of that?

I saved the tailgate for my new truck .. It wasnt much count anyhow the tailgate surround was missing and everything else is smooth worn out . I will however keep my eyes peeled .. Not too long ago i threw away a tailgate that was caked with bondo but was a low use tailgate and had all that stuff :banghead:

TTT About To Have Cab Removed, Building Truck bed Trailer Out the rest. The cab Has A Hole In the roof for a VHF Antenna Otherwise Clean Cab. Doors/ Fenders/Coresupport/EvapCoils/ Ac Controls/ And many other parts still avaialble.

Do you still have the 427 engine for sale & if so is it all complete?

not sure if I sent this to the right person, But do you have the 427 engine up for sale? please let me know.

You must be confused .. I have no 427

Can you take a picture of the intrusment cluster - and how much you would want for it. Also - list if there are any guages that are "Twitchy" or not always functional.

Pics can be viewed 15 posts up from this one.. The gas gauge and speedometer work fine no twitcyness.

How much for the A/C controls and shipping to 67209?

There is a pic of the ac controls on the first page.. Ill take 25 Plus 15 shipping so 40 bucks shipped. Let me know.

What part of DFW are you in?

Im Not acutally in DFW I live in an Armpit of a town so i just put a landmark for the location ..

Im located in quinlan 75474

I am looking for a vergin crank shaft how much for yours :gmc:

Im Uncertain as to the condition I assume it to be STD As the bores are but you never know.

Id have to have 75 for it Mainly due to haveing to pull a good engine apart to remove it Id pull a main and a rod if you were seriously interested to see if it has been ground or not.

You dont have any local engine builders? They could get you one turned down to 0.10 ready to install Or even get a STD. one Would be cheaper than shipping too.

check your pm

I am looking for a solid one piece rear window for a 93 std cab.

Sorry ive already sold the rear window locally.

Few more pics added Will Take 40$ For the evap coils and all hardware that atttachs it It looks ruff but system had freon in it still so no leaks.

You still parting this truck out?
I'm interested in your grill, radiator, and the front end support that spans the front of the truck and connects to right and left panels (don't know the name of the part)
thanks

I Still Have Those Parts You Local? Prices are listed on the prior page as well as pictures.

I just read this and I have an '88 Chevy Pick-up Standard Cab, and my air vent on the right side of the glove box is broken. I believe it just un-bolts with 2-4 screws. I was wondering if you still had this and if so, I have n't been able to find one locally and it might be cheaper to get 1 from you.
Zip is 59801. Thanx

I Still Have Those Parts You Local? Prices are listed on the prior page as well as pictures.

I'm actually from Ogden Utah, I imagine this will make it more difficult.
I'm interested in the parts, your prices are good.
Would you still be interested in sending these parts out here?
And the front end support that spans the front of the truck and connects to right and left panels, is that called the "core support"?
thank you

Yeah its the core support I dont have a problem packing them up if you want to pay the shipping.

Id Take 60 for the core support. 40 for the grille and 20 for the radiator its a one row.

Ill check the air vent shortly..

Yeah its the core support I dont have a problem packing them up if you want to pay the shipping.

Id Take 60 for the core support. 40 for the grille and 20 for the radiator its a one row.

Ill check the air vent shortly..

cool.
check your pm's.

Are you Talking About The A/C Vent?

I left you a PM re: parts