...do you have a steel fan shroud v8 this truck had one looked odd though i remember it from when i was a kid but i think a water pump let go and killed it and the radiator the shrouds i have found are like fiberglass can you shed some light or do you have ?? if so how many $$$$ would it take to buy and ship 37659
o...what about a upper radiator pipe it used to have one of those too :but:
thanks,
jason
there has to be something i can buy :metal:

towrecker:

Thanks for the prompt reply. The factory fan shroud for the V8 trucks was fiberglass. I don't have any right now, however, you can get them at:

www.lmctruck.com
www.classicparts.com
www.oldchevytrucks.com
www.bowtiebits.com

If you need the upper radiator hose for a V8, I sell the hard pipe radiator hose like this:

http://67-72chevytrucks.com/vboard/showthread.php?t=322792

This kit includes the hard pipe, four tower clamps and two starter hoses. The complete kit is $50.00, plus $9.95 packaing & shipping.

Please let me know if I can help you with this item or other 4-5-6 Chevy truck parts in the future and thanks for the opportunity.

I would like to find a nice 1964-66 left drivers door custom cab moldeings. Ship to 91340.. Have a nice tailgate to trade??? Thanks

I would like to find a nice 1964-66 left drivers door custom cab moldeings. Ship to 91340.. Have a nice tailgate to trade??? Thanks

Good evening and thanks for the inquiry. I have a few nice sets fof 4-5-6 Chevy truck Custom cab sails.

Is the tailgate a fleetside or stepside? Chevy or GMC?

Please let me know and I will reply accordingly. Thanks for the opportunity.

Fleetside tail gate very nice from calif

fleetside tail gate very nice from calif
chevrolet

chevrolet

I have sent you a PM.

Do you have the throttle rod and swivel for a 63 chevy v8 4 bbl. That was taken off my truck before I got it. I'm unsure if a 6 cylinder one is different, but I need to connect to an eldelbrock carb. I'm at the lake of the ozarks zip 65037. Thanks

do you have drivers door for 65 C-10fleet with wing window. how much &shipped to 60002? thanks jw

Do you have the throttle rod and swivel for a 63 chevy v8 4 bbl. That was taken off my truck before I got it. I'm unsure if a 6 cylinder one is different, but I need to connect to an eldelbrock carb. I'm at the lake of the ozarks zip 65037. Thanks

Good morning and Happy Easter. Thanks for the inquiry. I know what you mean by the throttle rod, but I am unsure of what you mean by the swivel. I have factory V8 throttle rods and the accelerator assembly at the firewall, so if that is what you mean, I can help.

Please clarify what you need and I will reply accordingly and thanks for the opportunity.

do you have drivers door for 65 C-10fleet with wing window. how much &shipped to 60002? thanks jw

jw:

Good morning and Happy Easter. Thanks for the opportunity. I sell good, used door shells for $175.00, plus shipping, via Greyhound-Freight. You will have to pick the item up at the Greyhound terminal nearest your location. Greyhound-Freight costs $85.00.

Please let me know if I can help you with this item or other good, used 4-5-6 Chevy trucks parts in the future and thanks for the opportunity.

Tony,

Happy Easter to ya and tell me, what do you get for a bench seat for my '66..?

Thanks.

Sorry I was not clear, not having one I was unsure the correct wording. I need the rod that connects the part on the firewall and the end piece that threads on to the rod and fits in the carb allowing length adjustment. I'm unsure if it fits on a ball mounted on the carb or if it fits in a bushing in the carb and has a clip that holds it on. I called it a swivel because LMC call the clutch adjustment rod end piece a swivel -thanks again

hey lilred,
im looking for an intake manifold for the 315e gmc. please let me know if you have one and how much. also a fuel gauge for a 63 gmc would be much appreciated.

sorry about that lilred, the intake needed is for a 351e

Do you have any steering columns for 66 Chevy truck?

Thanks,Jimmy

Tony,

Happy Easter to ya and tell me, what do you get for a bench seat for my '66..?

Thanks.

66BowTieBoy:

Good afternoon and thanks for the inquiry. I have a few very nice factory bench seats, but the shipping would make them uneconomical. Have you checked craigs list in your area?

Sorry I was not clear, not having one I was unsure the correct wording. I need the rod that connects the part on the firewall and the end piece that threads on to the rod and fits in the carb allowing length adjustment. I'm unsure if it fits on a ball mounted on the carb or if it fits in a bushing in the carb and has a clip that holds it on. I called it a swivel because LMC call the clutch adjustment rod end piece a swivel -thanks again

jame:

Good afternoon and thanks for the inquiry. I have a throttle rod for a factory V8. It attaches to the carburetor at one end and to the accelerator linkage at the other end. It is $25.00, including the ride.

Please let me know if I can help you with this item or other 4-5-6 Chevy truck parts in the future and thanks for the opportunity.

hey lilred,
im looking for an intake manifold for the 315e gmc. please let me know if you have one and how much. also a fuel gauge for a 63 gmc would be much appreciated.

Adrian:

Good afternoon and thanks for the inquiry. I tried to send you an e-mail at the address you provided this morning, but it kicked it back. In any case, I don't have a factory 351E V6 intake manifold. I have put out a few feelers and will try to locate one for you.

Sorry I couldn't help you with this item, but please keep me in mind for other 4-5-6 Chevy/GMC truck parts in the future and thanks for the opportunity.

Do you have any steering columns for 66 Chevy truck?

Thanks,Jimmy

Jimmy:

Good afternoon and thanks for the inquiry. I have a few factory steering columns. Do you need an automatic, three speed or floor shift column? Please let me know and I will reply accordingly. Thanks for the opportunity.

The floor shift column,

Jimmy

The floor shift column,

Jimmy

Jimmy:

Thanks for the prompt reply. I have a few factory floor shift columns. Without the steering wheel, a good, used factory floor shift steering column is $100.00, plus $42.00 packaging & shipping, via UPS or FedEx-Ground.

I accept cashiers check, money order or PayPal at:

4-5-6chevytrucks@sbclobal.net

Please let me know if I can help you with this item or other 4-5-6 Chevy truck parts in the future and thanks for the opportunity.

hey lilred i was wondering how much you would sell me some wheel tubs for either year i do need a good pair.

Tony,

I'm in KC from time to time and maybe I could pickup at your place..? Need the whole thing, (seat & mountings). So what would it cost me?
Thanks.

hey lilred i was wondering how much you would sell me some wheel tubs for either year i do need a good pair.

Sal:

Good morning and thanks for the inquiry. A good, used set of rear fleetside wheel tubs is $125.00, plus $45.00 packaging & shipping, via UPS or FedEx-Ground.

Please let me know if I can help you with this item or other good, used 4-5-6 Chevy truck parts in the future and thanks for the opportunity.

Tony,

I'm in KC from time to time and maybe I could pickup at your place..? Need the whole thing, (seat & mountings). So what would it cost me?
Thanks.

Thanks for the prompt reply. A good, used factory bench seat with good, with original upholstery (one small tear) and factory seat tracks is $120.00, picked up at my shop in Kansas City, KS.

Please let me know if I can help you with this item or other good, used 4-5-6 Chevy truck parts in the future and thanks for the opportunity.

Do you have any H033 rear axle parts?such as the differential? any help is greatly appreciated thanks Bill:metal:

Do you have any H033 rear axle parts?such as the differential? any help is greatly appreciated thanks Bill:metal:

Bill:

Good afternoon and thanks for the inquiry. I have half a dozen factory 6 lug rear-ends, but I haven't checked the tag on any of them, so I don't know if they are HO33. If the tag is missing, will the HO33 be stamped on the passenger side axle tube? If so, I can check them. I see you are in Omaha, NE. Do you get to Kansas City much? If so, I can meet you at my shop and check out what I have. Please let me know your thougths and thanks for the opportunity.

soory i havent got back to you on the wheels tubs so what am i looking at if i get some that it fair shape or along them line?

soory i havent got back to you on the wheels tubs so what am i looking at if i get some that it fair shape or along them line?

I either have a great set of a set with some rust on the flanges, so what is acceptable?

Hey Tony,

Do you have a nice clean 6 lug steel 15 x 5.5 wide wheel? If so how much with shipping to 77510. I need a spare for my 59 Apache.

Thanks

Hey Tony,

Do you have a nice clean 6 lug steel 15 x 5.5 wide wheel? If so how much with shipping to 77510. I need a spare for my 59 Apache.

Thanks

Good evening and thanks for the inquiry. I don't have any of the skinny factory 6 lug steel wheels at this time. Sorry I couldn't help you with this item, but please let me know if I can help you with other 4-5-6 Chevy truck parts in the future and thanks for the opportunity.

could you post pics of both?

Hi Lil Red,
Do you have factory components to add power steering to my 66 GMC 351E? I'm trying to find stock before I consider the later model conversion. I understand the brackets for the 351E a difficult to come by. Thanks.

Dennis Arseneault
'66 GMC LWB Fleetside 351E
Avondale, AZ

Hi Tony, I'm in need of a front clip for my 63. The rad support is rusted through at the body mounts. Taking it apart found I need everything. Grill support, radiator support, both inner and outer fenders. I see all the suppliers sell repo stuff. Since your pretty close (only about 2.5 hours) thought I would see if you have a rust free set up. My cab is pretty rough aswell - I would consider a cab swap or even a complete parts truck if you have a fairly rust free one with out a title or no drivetrain ect. I'm not partial to 1963 items actually wanted a 64-6 in the begining but this is what I found. It has turned out much worse than first expected. Thanks Jame

Lil Red,

I need a pair of good OEM trailing arms? I think they are all the same 60-66?

happen to have any?

thanks in advance

Hi Lil Red,
Do you have factory components to add power steering to my 66 GMC 351E? I'm trying to find stock before I consider the later model conversion. I understand the brackets for the 351E a difficult to come by. Thanks.

Dennis Arseneault
'66 GMC LWB Fleetside 351E
Avondale, AZ

Dennis:

Good afternoon and thanks for the inquiry. Sorry for my delay in responding. I don't have any accessory items for the 305 or 351 GMC V6 engines. Sorry I couldn't help you with this item, but please let me know if I can help you with other '60-'66 Chevy/GMC truck parts in the future and thanks for the opportunity.

Hi Tony, I'm in need of a front clip for my 63. The rad support is rusted through at the body mounts. Taking it apart found I need everything. Grill support, radiator support, both inner and outer fenders. I see all the suppliers sell repo stuff. Since your pretty close (only about 2.5 hours) thought I would see if you have a rust free set up. My cab is pretty rough aswell - I would consider a cab swap or even a complete parts truck if you have a fairly rust free one with out a title or no drivetrain ect. I'm not partial to 1963 items actually wanted a 64-6 in the begining but this is what I found. It has turned out much worse than first expected. Thanks Jame


Jame:

I sent you a PM regarding a '60-'63 Chevy C10 front clip and cab. Please let me know if I can help you with these items or other '60-'66 Chevy truck parts in the future and thanks for the opportunity.

Lil Red,

I need a pair of good OEM trailing arms? I think they are all the same 60-66?

happen to have any?

thanks in advance

Good afternoon and thanks for the inquiry. I sent you a PM about the trailing arms.

Please let me know if I can help you with this item or other good, used 4-5-6 Chevy truck parts in the future and thanks for the opportunity.

Do you have one of these ? It's for the basic heater or whatever it's called out of my 63 truck. It's the heater that is completely self contained under the dash and not in the engine compartment.

I need a decent one to powdercoat. Mine is tweaked a bit too far to ever be repaired again.

http://i276.photobucket.com/albums/kk33/Adventure-rider/The%2063%20truck/63chevy028.jpg
http://i276.photobucket.com/albums/kk33/Adventure-rider/The%2063%20truck/63chevy029.jpg
http://i276.photobucket.com/albums/kk33/Adventure-rider/The%2063%20truck/63chevy030.jpg

Do you have one of these ? It's for the basic heater or whatever it's called out of my 63 truck. It's the heater that is completely self contained under the dash and not in the engine compartment.

I need a decent one to powdercoat. Mine is tweaked a bit too far to ever be repaired again.

http://i276.photobucket.com/albums/kk33/Adventure-rider/The%2063%20truck/63chevy028.jpg
http://i276.photobucket.com/albums/kk33/Adventure-rider/The%2063%20truck/63chevy029.jpg
http://i276.photobucket.com/albums/kk33/Adventure-rider/The%2063%20truck/63chevy030.jpg

TX:

Good morning and thanks for the inquiry. I have the item you are looking for. This part including shipping is $40.00.

I accept cashiers check or money order at the address in my signature or PayPal at: 4-5-6chevytrucks@sbcglobal.net

Please let me know if I can help you with this item or other good, used '60-'66 Chevy truck parts in the future and thanks for the opportunity.

I am looking for wheel tubs for my 64 GMC ( the best set that you have ) ship to 20751.
Thanks
James

Hi, I need a 4bbl air cleaner for a 66 c20 can you help ? thanks !! Pm me also

do you have patch panels?

lookin for drivers side floor panel, inner and outer rocker panel(driver side), lower rear fender panel for front fender(both sides) ext. rubber kit, window channel kit, shipped to 28083

thanks
karl

I am looking for wheel tubs for my 64 GMC ( the best set that you have ) ship to 20751.
Thanks
James

James:

Good morning and sorry for my delay in responding. I have a few very nice sets of fleetside wheel tubs, that are rust-free. They are $125.00 per pair, plus $28.00 shipping, via UPS or FedEx.

Thanks for the opportunity and please let me know if I can help you with any good, used 4-5-6 Chevy truck parts in the future.

Hi, I need a 4bbl air cleaner for a 66 c20 can you help ? thanks !! Pm me also

Good morning and thanks for the inquiry. I have a few good, used 4-5-6 Chevy truck factory 4-barrel air cleaners. They are $40.00, plus $12.00 shipping, via UPS or FedEx.

Thanks for the opportunity and please let me know if I can help you with this item or other good, used 4-5-6 Chevy truck parts in the future.

do you have patch panels?

lookin for drivers side floor panel, inner and outer rocker panel(driver side), lower rear fender panel for front fender(both sides) ext. rubber kit, window channel kit, shipped to 28083

thanks
karl

Karl:

Good morning and thanks for the inquiry. I sell good, used parts for 4-5-6 Chevy trucks, so I can't help you with new patch panels or other new items. Here is a list of aftermarket truck parts suppliers, that sell items for these trucks:

www.bowtiebits.com
www.lmctruck.com
www.classicparts.com
www.oldchevytrucks.com
www.ecklerstrucks.com
www.gspp.com
www.truckandcarshop.com
www.harmons.com
www.oldmusclecars.com
www.classicchevroletparts.com
www.classicindustries.com
www.bobschevytrucks.com
www.brotherstrucks.com
www.mar-k.com
www.wheelvintiques.com
www.totallystainless.com
www.earlyclassic.com
www.horkeyswoodandparts.com
www.raybuck.com
www.americanclassic.com
www.yogisinc.com
www.rbsauto.com
www.obschevy.com
www.cheyennepickup.com
www.chevypickupparts.com

Most of them offer a free catalog and they are good reading. Welcome to the forums and thanks for the opportunity. Please let me know if I can help you with any good, used 4-5-6 Chevy truck parts in the future and good luck with your project.

ok pm me how you would like the payment of $52.00 I will get this to you asap. I have paypal or will send out a m.o

Tony do you have any good 350 turbo 3 speed transmisions short tails.. price??? maybe picture thanks buddy..

pm sent

Tony,
Do you have this clutch pedal arm linkage thing? Mine wore out... I'm not sure if it's factory though. Also, that upper linkage piece that connects to the arm also. (http://67-72chevytrucks.com/vboard/showthread.php?t=343063)

http://i82.photobucket.com/albums/j257/air_cooled65/IMG_1250.jpg

thanks

pm sent

I received your PM and payment. Thanks for your business.

Tony, did my frame piece and crossmember ever ship out ?

Hi, do you have a Hallander interchange booK. I am looking for a pair of wheel hubs that fit a 1962 (tapered roller bearings). I suspect they are the same as the years you deal in. If you have them I need um. Thanks Marshall

Tony, did my frame piece and crossmember ever ship out ?

Kevin:

Thanks for the follow-up. Last week was a bear...finishing up with one swap meet and getting ready for another one, so only shipped a portion of my truck parts orders last week. I will be shipping again this week, so your's will go out this week. I have to butcher a chassis for your items, so I will have a little time getting the parts cut off and packaged.

Sorry for my delay and thanks for your patience.

Im guessing you dont have a 3 speed 350 turbo transmission.. thanks anyway..

Kevin:

Thanks for the follow-up. Last week was a bear...finishing up with one swap meet and getting ready for another one, so only shipped a portion of my truck parts orders last week. I will be shipping again this week, so your's will go out this week. I have to butcher a chassis for your items, so I will have a little time getting the parts cut off and packaged.

Sorry for my delay and thanks for your patience.

I'd appreciate you just refunding my paypal. I thought you were going to ship it to me last week. I am tired of waiting. I will get the stuff locally.

I'd appreciate you just refunding my paypal. I thought you were going to ship it to me last week. I am tired of waiting. I will get the stuff locally.

Sorry I couldn't turn your parts around in five days. Refund complete. Good luck with your project.

Im guessing you dont have a 3 speed 350 turbo transmission.. thanks anyway..

I don't have a 350 Turbo short shaft, but if I did the shipping would be more than the tranny, so you would be better off finding one locally.

Hi, do you have a Hallander interchange booK. I am looking for a pair of wheel hubs that fit a 1962 (tapered roller bearings). I suspect they are the same as the years you deal in. If you have them I need um. Thanks Marshall

I don't Hollander Exchange manual, so I am not able to tell you if the '60-'66 are all the same. I have a set of front hubs from a '65, that have been refinished for a frame-off restoration, but we did a disk brake conversion instead. If you know for sure they will work, they are for sale.

Hey Tony,
I'm looking for a 283 4bbl carburator and intake setup with breather. Have you got anything? Also would like to know where the best place is to get a four row desert cooler radiator for my 66?

I am looking for a dash out of a 61 or similiar years. Pm me a price shipped to 35960 if you have one.

Thanks, Kade

Red, how much for the hubs?

I received your PM and payment. Thanks for your business.

I definitely went them but I have not sent the payment yet.I will send the payment this weekend.
James
just want to keep things on the up an up.

Hey Tony,
I'm looking for a 283 4bbl carburator and intake setup with breather. Have you got anything? Also would like to know where the best place is to get a four row desert cooler radiator for my 66?

Thanks for the inquiry. I don't have any factory 4-barrel carb/intake setups. I have sold two 4-barrel breathers in the past few weeks, so I am out of these, as well.

Thanks for the opportunity and please keep me in mind for other good, used 4-5-6 Chevy truck parts in the future.

I definitely went them but I have not sent the payment yet.I will send the payment this weekend.
James
just want to keep things on the up an up.

James:

Thanks for the prompt reply. I checked my notes and PayPal, but was unable to find a record of payment, so thanks for the heads-up. Let me know and I will reply accordingly. Thanks.

I am looking for a dash out of a 61 or similiar years. Pm me a price shipped to 35960 if you have one.

Thanks, Kade

Kade:

Good evening and thanks for the inquiry. I have a few good, used '60-'63 Chevy truck dashes. Are you looking for the dash cluster or the entire dash assmembly, that goes from "A" pillar to "A" pillar? Please let me know and I will reply accordingly.

Hey Tony,
I'm looking for a 283 4bbl carburator and intake setup with breather. Have you got anything? Also would like to know where the best place is to get a four row desert cooler radiator for my 66?

Bob:

I do have a few good, used factory Harrison 4-core radiators. I just had one re-cored, but it was $400.00, to do so. It looks like new and has the factory tranny line connections on the bottom tank for an automatic transmission. Also, I just purchased a 3-core from O'Reillys for around $200.00. This was after checking the offerings from LMC Truck and Classic Parts, since both are in the Kansas City area and I could visually inspect them before purchasing one. Needless to say, they say they are factory replacements, but the tanks are not even close, plus the cost was about double what I paid for the radiator from O'Reillys. If you are interested, please let me know and I will reply accordingly. Thanks for the opportunity.

Red, how much for the hubs?

Are you just looking for the hubs or the entire hub assembly, including the brakes, drums, hubs and hoses? I have all of the above, so let me know what you need and I will reply accordingly. Thanks for the opportunity.

Kade:

Good evening and thanks for the inquiry. I have a few good, used '60-'63 Chevy truck dashes. Are you looking for the dash cluster or the entire dash assmembly, that goes from "A" pillar to "A" pillar? Please let me know and I will reply accordingly.

I need the whole dash from pillar to pillar, I am not worried about the cluster, any of the knobs, radio, heater contols, etc but I would like to have the glove box door included. If it is not too much trouble the pedal bracket that mounts to the dash and firewall would be nice and maybe the column strap. My zip is 35960.

Thanks, Kade

James:

Thanks for the prompt reply. I checked my notes and PayPal, but was unable to find a record of payment, so thanks for the heads-up. Let me know and I will reply accordingly. Thanks.

Ok I sent the payment this morning.
Thanks
James

1 - where is this place in the forums for get rid of free parts? I have looked, and PM'd a mod and have got no response...

2. Shouldn't you be a forum vendor? You are advertising your business and have a 1-2 year thread telling everyone you sell parts....that is not normal selling of unneeded parts...

The place on the site to offer parts for free is under the Parts for Sale thread, by starting your own thread, if you have parts to offer for free.

After several years of being a Site Supporter, my subscription was changed to a Site Vendor, without my consent and later changed back to Site Supporter, without my knowledge, so I don't have any control over that. By the way, I am an individual with a collection of 4-5-6 Chevy trucks and in the process and collecting and restoring them, I have acquired a massive amount of parts, so I offer them for sale. I don't operate as a business, however I am in the process of making that transition, since my primary business, commercial general contracting, has been rather slow.

Thanks for your opinion on the situation and let me know if I can help you with any good, used 4-5-6 Chevy truck parts in the future.

No problem, I just remember you as being a vendor at one time.

Tony,
My wife picked me up a 66 while on deployment to the desert, however the hood is all rusted out. I am looking for hood that is in real good condition. I am also looking for the passenger side wing window assembly. I will need the complete frame and everything. I will be home in a couple weeks from deployment, and will be in Coffeyville, Ks around the 22nd of June. Any help you can give me will be greatly appreciated. If shipping is not too much my zip is 32068. Thanks for your help

Brian

Parts arrived,
Thanks
James