Re: C10CJ: A Pro-touring '71 Stepside on a No Limit Pro-C10 Chassis
Quote:
|
Re: C10CJ: A Pro-touring '71 Stepside on a No Limit Pro-C10 Chassis
5 Attachment(s)
Update ...
I'm getting really close to firing this thing up. The electrical system is 99% done. A few ground wires to finish off and then testing. After testing, finish up the wire braid and get everything mounted with cushion clamps. Over the last few days I completed the PDM. Here it is painted up. I also added a mounting hole for my coolant recovery tank. Attachment 1740209 The back side. Attachment 1740210 Start of wiring. All metri-Pack 280 terminals so easy to assemble. Just takes time. Attachment 1740211 All wired up. Attachment 1740212 All the fuses, relays and circuit breakers installed. All in all this set of boxes houses 12 additional circuits and 6 relays, as planned. Here you can really see the amount of expansion room I've got. I could have crammed it all in one box, but I figured I'd have some expansion room. Notice I also had to go from one hole to 2 holes. Lots of big wires in the bottom hole, like several 10 ga and one 8 ga. So if I need to expand, probably wind up with a 3rd hole or make the top one a little bigger. Attachment 1740213 |
Re: C10CJ: A Pro-touring '71 Stepside on a No Limit Pro-C10 Chassis
5 Attachment(s)
To feed that PDM, I needed a power feeding setup. If you recall from way back when, I mentioned I was going to install some studs so I could easily move the battery once I figure out where I want it. So here's the final solution. I still have some cleanup work to do, but this is good enough for testing and to get the engine fired up. I need to fab a new battery box/hold down as the current one over the years suffered from corrosion and was very thin in part. I wound up blowing the factory battery mount apart by drilling the spot welds out. The bottom was the only piece in bad shape. I'm currently thinking about getting one of these pre-cut units and welding it to the factory side pieces.
So here's the power feed board. There are two different power feeds here. The primary feed, which is the two large studs at the bottom, provide power to the fuse block and PDM as well as tie in the alternator. That circuit is protected by a 200 amp midi fuse. The other feed is the ECU feed. The ECU wants clean power. So to get clean power it needs to go straight to the battery. So that's the MAXI fuse up top. The MAXI provides power to the ECU and vintage air/Dakota digital controllers. It is a completely separate power circuit from everything, so the possibility of getting disrupting electrical transients should be minimized. Looks a little messy because I do plan to either paint or polish that aluminum backing plate so it will come apart shortly after I get the engine fired up. Plus found out my engine ground is too short if I put my inner fender in, but that's an easy fix. Attachment 1740214 I also got the transmission harness redone. Going to EFI, I'm letting the ECU control the bits of the trans it can control, which in this case is the torque converter clutch. But, I had to re-wire the guts and redo the harness to send the 4th gear signal to the ECU and so forth. It's also got my speedo tied in. Attachment 1740215 And the last harness to make was the fuel tank. Here it is. I may wind up dropping the tank so I can put a cable clamp down in there to keep the connector from beating itself up. Overall I'm pretty happy with how the electrical is turning out. Attachment 1740216 A couple shots just showing some more of the routing. I'm using the Painless Performance Classic Braid to cover everything up. I really like the look of it and it seems to almost look OEM like. Or maybe that's my OCD. Ha! Attachment 1740218 Attachment 1740219 |
Re: C10CJ: A Pro-touring '71 Stepside on a No Limit Pro-C10 Chassis
Chris, gotta love how wiring can be so time consuming hey, I try to tell customers that is is the worst job on the entire vehicle, so tedious and time consuming just to make it all look great, hidden and accessible at the same time. Love it btw!!!!
|
Re: C10CJ: A Pro-touring '71 Stepside on a No Limit Pro-C10 Chassis
Quote:
|
Re: C10CJ: A Pro-touring '71 Stepside on a No Limit Pro-C10 Chassis
Quote:
|
Re: C10CJ: A Pro-touring '71 Stepside on a No Limit Pro-C10 Chassis
Quote:
|
Re: C10CJ: A Pro-touring '71 Stepside on a No Limit Pro-C10 Chassis
5 Attachment(s)
Ok all ... The electrical system is FINISHED! and TESTED!
It's been a long time since these gauges saw power. I've got all the circuits I can test before running the engine tested. I've intentionally had the fuel pump disconnected as there is no fuel in the tank and the pump would not like that. Attachment 1741013 Need to figure out where these two are going to go. That little Dakota Digital Heater/AC control is going to be awesome. Just set a temp and it adjusts the unit to maintain that temp. Attachment 1741014 Soon ... that tach will say something other than 0 RPM. Attachment 1741015 Priming the LS ... yep, it can be done. I followed some directions here loosely, and did not put a hose on the oil pan. That was why their system didn't work as it restricted the flow too much. They also used too large of a bucket so the oil pickup would come uncovered. My mods: -3 gallon bucket -No return tubes, just a funnel under the oil pan to catch the oil and return to the bucket -Total cost, about $60. The SBC oil pump is perfect. Why? because a 1/4" NPT taps goes right in to the pump output without any drilling. Seriously, I put the pump in a vise and tapped away. It was harder to install the pickup tube. Oh, and boy was that fun at the autoparts store getting the SBC oil pump. I walked in, there were 3 of them, a younger one helped me (let's say early 20s): Clerk:How can I help you? Me: I need a SBC oil pump. Clerk: What year vehicle? Me: (holding a straight face) A 2017 Home Depot 3 gallon bucket Clerk: (just stared at me) The others: one started laughing, the other was dumbfounded Me: (I finally smiled) Clerk: Ok, seriously... Me: I was being serious. Clerk: (finally started laughing) Me: It's a priming bucket for an LS Clerk: I gotcha Me: Let's just go with a 1972 Chevy 1/2 ton van with a 350 I'll say, this thing works great so far. I was getting around 40 psi of oil pressure as measured through the gauge/ECU. LS engines are actually a bear to prime. They can take over 15 minutes of constant priming and manual crank rotation to get all the circuits primed. Hence why many guys just pull the plugs and roll it over until they get pressure. I'm old school I guess. Attachment 1741016 The bucket just feeds right in to the plug on the driver side of the block at the oil pump. Attachment 1741017 Oh, and I did roll this thing over briefly when I checked the starter. Um, it's like a dragon stuck in a cave fighting to get out. I mean, it hit hard. I could feel EVERY.SINGLE.COMPRESSION.STROKE. Three to be exact. I don't know if my 10 yr old yellow top Optima is going to like this one. |
Re: C10CJ: A Pro-touring '71 Stepside on a No Limit Pro-C10 Chassis
very cool build, nice work on all the details!
|
Re: C10CJ: A Pro-touring '71 Stepside on a No Limit Pro-C10 Chassis
Quote:
|
Re: C10CJ: A Pro-touring '71 Stepside on a No Limit Pro-C10 Chassis
Just finished checking out your build thread. Great job. Thanks for sharing the info on the PDM's. Looking back, I wish I would have done it with the parts you used. I did a quick and dirty set up that works, but just does not look as clean. I might have to redo it some day when I decide that looks are important...lol.
|
Re: C10CJ: A Pro-touring '71 Stepside on a No Limit Pro-C10 Chassis
Quote:
|
Re: C10CJ: A Pro-touring '71 Stepside on a No Limit Pro-C10 Chassis
C10CJ is ALIVE!!!!
That Don Hardy Stroked LS fired right up the 1st try! A major milestone for the truck. Now setting the sites on the LMC C10 Nationals in May. Who wants to join me? |
Re: C10CJ: A Pro-touring '71 Stepside on a No Limit Pro-C10 Chassis
2 Attachment(s)
coreyjonesdesigns sells panels that go in place of the factory heater controls that fit that heater control
|
Re: C10CJ: A Pro-touring '71 Stepside on a No Limit Pro-C10 Chassis
Beastly, congrats!
|
Re: C10CJ: A Pro-touring '71 Stepside on a No Limit Pro-C10 Chassis
Quote:
I've never dealt with aluminide material. Can it be sanded smooth? I'll definitely keep you in mind though when I get to deciding on something for the near term. Quote:
|
Re: C10CJ: A Pro-touring '71 Stepside on a No Limit Pro-C10 Chassis
2 Attachment(s)
thats cool brother. just thought Id pass along some info. yes it can. its super easy to sand.
|
Re: C10CJ: A Pro-touring '71 Stepside on a No Limit Pro-C10 Chassis
Quote:
|
Re: C10CJ: A Pro-touring '71 Stepside on a No Limit Pro-C10 Chassis
Hey all ... I tossed together a short video on that priming bucket in case you have some interest in seeing a few more details.
|
Re: C10CJ: A Pro-touring '71 Stepside on a No Limit Pro-C10 Chassis
Quote:
|
Re: C10CJ: A Pro-touring '71 Stepside on a No Limit Pro-C10 Chassis
Quote:
|
Re: C10CJ: A Pro-touring '71 Stepside on a No Limit Pro-C10 Chassis
1 Attachment(s)
Ok Guys! It's Official!! C10CJ is signed up for the C10 Nationals May 4-5 @ Texas Motor Speedway. The first major goal has been set!
Attachment 1744652 |
Re: C10CJ: A Pro-touring '71 Stepside on a No Limit Pro-C10 Chassis
Quote:
|
Re: C10CJ: A Pro-touring '71 Stepside on a No Limit Pro-C10 Chassis
Quote:
|
Re: C10CJ: A Pro-touring '71 Stepside on a No Limit Pro-C10 Chassis
Quote:
Quote:
|
All times are GMT -4. The time now is 08:54 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com