Re: Porterbuilt Dropmember
1 Attachment(s)
Quote:
Not sure what you are looking for. You can buy "bulkhead" PTC fittings that would mount in the frame rail. https://www.grainger.com/product/EATON-WEATHERHEAD-Bulkhead-Union-2ZKY6?s_pp=false&picUrl=//static.grainger.com/rp/s/is/image/Grainger/2ZKY4_AS01?$smthumb$ |
Re: Porterbuilt Dropmember
1 Attachment(s)
This is a clean install also,...
http://67-72chevytrucks.com/vboard/s...d.php?t=390299 |
Re: Porterbuilt Dropmember
1 Attachment(s)
Quote:
I have no problem drilling a hole in the frame. I'm just trying to figure out if people are coming from the front side of the front crossmember (red) or from the backside of the front crossmember (blue). If you come from the front, you have to loop the air lines 180. If you come from the backside, you have to contend with the brake lines and the shock mounts. Either way, I don't see and easy or clean way to do this..... |
Re: Porterbuilt Dropmember
Quote:
|
Re: Porterbuilt Dropmember
2 Attachment(s)
Here's a pic I took at Delmo's a few months back.
|
Re: Porterbuilt Dropmember
1 Attachment(s)
Quote:
R/ |
Re: Porterbuilt Dropmember
1 Attachment(s)
Quote:
|
Re: Porterbuilt Dropmember
Quote:
http://www.billetspecialties.com/tru.../ls-chevrolet/ |
Re: Porterbuilt Dropmember
Quote:
|
Re: Porterbuilt Dropmember
4 Attachment(s)
I am just gonna leave these here for yall to check out!:metal:
I am getting so close I can taste it! |
Re: Porterbuilt Dropmember
Super clean. I say run it bed less
|
Re: Porterbuilt Dropmember
I most definitely will for a while especially because it will take me a while to build the bed structure to clear the notch and what not.
|
Re: Porterbuilt Dropmember
5 Attachment(s)
Quote:
This Rooke truck is on point. Would like to see a build thread on it: Attachment 1818954 Attachment 1818955 Attachment 1818956 Attachment 1818957 Attachment 1818958 |
Re: Porterbuilt Dropmember
5 Attachment(s)
Pluggin' away...
Once I get it all assembled, checked for clearance etc, and working with the body on it... I'll blow it all back apart for paint & powdercoat. I'm having an issue with the BBC sitting way low in the chassis, but I actually found that in post #597 I asked and was answered, that the mounting tabs for the SBC and BBC are the same. I can't even use a set of manifolds with the motor right now as it sits...it needs to come up 3/4" or so... Waiting to hear back from PB now. |
Re: Porterbuilt Dropmember
4 Attachment(s)
Quote:
Few more pics: Attachment 1835190 Attachment 1835193 Attachment 1835191 Attachment 1835192 |
Re: Porterbuilt Dropmember
Quote:
|
Re: Porterbuilt Dropmember
bump this.
|
Re: Porterbuilt Dropmember
3 Attachment(s)
Newer pics, but I’m no where near done. First pic is ride height.
Remember, I’m a touring front DM and mild rear DM. The kmember lays on the concrete. |
All times are GMT -4. The time now is 12:47 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com