Re: 67cheby DM 3.2 install, W/PB 4link, PB hood hinges
 

Lookin good!

How did you ensure the rear of the frame is positioned correct since it was chopped off? I ask because I need to re-do a shotty c-notch job and I'm looking for some pointers on how to keep everything in the correct position in order for all the bolt holes/bumper to line up correctly.

Re: Raising the bed floor 67cheby
 

looks good

i like how you tubed the firewall

Re: Raising the bed floor 67cheby
 

looking good.

Re: Raising the bed floor 67cheby
 

Looking very good!!!

Re: 67cheby DM 3.2 install, W/PB 4link, PB hood hinges
 

the ideal way would be to put it on a frame table and secure everything, we just did alot of measuring and alot more measuring

Re: Raising the bed floor 67cheby
 

thanks for the compliments

Re: Raising the bed floor 67cheby
 

its lookin good

Re: 67cheby DM 3.2 install, W/PB 4link, PB hood hinges
 

a little more progress, notch welding done, set the bed on for the first time , pic of the truck at ride height

Re: 67cheby DM 3.2 install, W/PB 4link, PB hood hinges
 

Lookin good

Re: Raising the bed floor 67cheby
 

Looks good! :metal:

Re: 67cheby DM 3.2 install, W/PB 4link, PB hood hinges
 

nice progress!!! Looking great!

Re: 67cheby DM 3.2 install, W/PB 4link, PB hood hinges
 

Man that looks good... and with the way you raised the floor it looks fairly stock. What are the plans for the center of the floor where the notch will pass through?

Re: 67cheby DM 3.2 install, W/PB 4link, PB hood hinges
 

well the original plans was to not go through the floor at all ... but that was before i found this website and that dang Porterbuilt..... i am going to cover it with a hinged cover and either have the cover airbrushed or wrapped to match the wood on the bed floor .. hopefully that will blend it in a little, i am trying to go with somewhat of a stock look for this truck, everyone laughs when i say that but the engine looks stock, the interior will look stock and i am keeping all of the trim and badges, oh and thanks for the bed compliment alot of effort and cash went into making it look that way

Re: 67cheby DM 3.2 install, W/PB 4link, PB hood hinges
 

Hey stock and dropped is the only way to go in my opinion... so more power to you. :D

Any chance you'll have this thing at the Nat's in September? Had hoped you were going to make it this past year.

Re: 67cheby DM 3.2 install, W/PB 4link, PB hood hinges
 

me too, i think i have to make it a priority even if i have to show unfinished

Re: Raising the bed floor 67cheby
 

All that bed work & still not gonna clear the notch?
The work looks good though!

Re: Raising the bed floor 67cheby
 

when i was raising the bed floor it would have covered what i was doing.... that was before the Dropmember

Re: Raising the bed floor 67cheby
 

hmmmmmm it isnt too bad
if you make a woodfloor in the bed you might be able to put an extra layer under the floor to raise the floor itself say another 2 inches on the bars and edges and still get a flat floor across , it will take a bit of longer hardware but i dont think it will show anywhere else than near the gate the inner fender gives enough clearance for the drop so its an eazy way out

Re: 67cheby DM 3.2 install, W/PB 4link, PB hood hinges
 

Well its been a toss up to figure out what to use to center the rearend... Just bit the bullet and ordered the KP Components watts link... i hope i like it

Re: Raising the bed floor 67cheby
 

Let me know how that works out. Thats my plan as well

Re: Raising the bed floor 67cheby
 

hopefully before long you will see pics, i am pretty pumped, now to get my bags and shocks, compressors,tank,battery , train horns, mounted there is going to be no room left under my bed

Re: Raising the bed floor 67cheby
 

Sweet!!!

Re: Raising the bed floor 67cheby
 

I thought you ordered the dropmember to run the stock A/C!!:lol: Funny how the snowball effect takes place! Truck is looking good!!

Re: Raising the bed floor 67cheby
 

Hey why you gotta be bustin me, when i started this truck it was just supposed to be a static drop !!! nothing else...... oh well you know how it goes, heres a few more pics , i smoothed out the welds on my step notch, took the last rivet from the bottom of my frame that was holding it up off the ground... finally laying flat!!

Re: 67cheby DM 3.2 install, W/PB 4link, PB hood hinges
 

looks awesome man! Keep up the good work!