Re: Parting 1986 Suburban K20 4x4
 

I will check and get back with you. Rear?

Thank you,
Thomas

Re: Parting 1986 Suburban K20 4x4
 

Hi Les,

Here are photos of the bezel. Not the greatest condition but no cracks anywhere.

I have the brackets you need for $50.00 for the pair. I will need to get them removed from a truck we have here. I do not have anything loose currently. These brackets are riveted to the cross member near the frame rails correct?

I believe they would be correct for an 81-87 K10 pick up or 81-91 suburban/blazer?

Nothing on the seat belt cover.

Let me know and I can figure out shipping for everything.

Thank you,
Thomas

Re: Parting 1986 Suburban K20 4x4
 

Thomas,

sent PM

Les

Re: Parting 1986 Suburban K20 4x4
 

Yes

Re: Parting 1986 Suburban K20 4x4
 

Item received. Thank you so very much!

Re: Parting 1986 Suburban K20 4x4
 

Do you still have the axles?

Re: Parting 1986 Suburban K20 4x4
 

What exactly do you need? Complete rear diff assemblies from rotor to rotor / drum to drum, or just axle shafts? What gear ratio are you looking for? I think the ones in this Suburban sold but we have others.

Let me know.
Thank you,
Thomas

Re: Parting 1986 Suburban K20 4x4
 

I need complete assembly's, I would like to have 410 ratio front and rear with a full floater for the rear. I am going to put this under a 87 1/2 ton and would like for them to be bolt in.

Re: Parting 1986 Suburban K20 4x4
 

I have a rear with 86,000 miles, with posi and full float axles for $400.00 lug nut to lug nut.

I have a front (unknown mileage) for $500.00 lug nut to lug nut. Both 4:10 gears.

I have quoted shipping for these before to and it was $350.00 to ship the rear to NJ. My guess is you would be looking at at least $600.00 if not more for shipping alone.

Let me know.

Thank you for the interest,
Thomas

Re: Parting 1986 Suburban K20 4x4
 

Would shipping still be that high if they are strapped to the same pallet?

Re: Parting 1986 Suburban K20 4x4
 

Pm sent

Re: Parting 1986 Suburban K20 4x4
 

Do you still have the suburban for parts? Looking for the parts that hold down the jack in the inner fender.

Re: Parting 1986 Suburban K20 4x4
 

Is the trans tunnel a high hump? If so how much?

Re: Parting 1986 Suburban K20 4x4
 

Do you have a factory K20 bottle jack that works? Could you please post a pic if you do?

Re: Parting 1986 Suburban K20 4x4
 

Checking to see if you have two dent and rust free rear inner wheel housings,
is the grill from the red suburban pictured still available, bumper brackets for a rear sport sport bumper, core support for single headlight (same set up as pictured in the ad) and possibly an electronic speedo cluster. All this going on an 87 R10.
Thanks, Mike

Re: Parting 1986 Suburban K20 4x4
 

Hi do you have a vent window assemble that will fit my 84 C10 Silverado? I need the passenger side. Thanks

Re: Parting 1986 Suburban K20 4x4
 

Parts wanted for pickup from other trucks in your yard or other members here...

Catalytic converter heat shield and brackets, 1987 4x4 standard cab or any 1987-1991 one ton, standard cab.
87-90 454 TBI Dipstick Tube
87-91 V30/V3500 TBI Intermediate Fuel Feed Line from fuel filter to braided line.
Rear DRW Hubs.
73-91 Dually Bed harness, filler panels (inner to outer skin), wiring protectors, rear red fender light.
87 GMC service manual.
87 GMC wiring diagrams.
3.73 Dana 60 Front and Dana 70 HD Rear.
Tan manual window door panels (clean) (81-87 old style) Scottsdale, or better yet Silverado/Sierra Classic.
Tan and red/maroon OEM floor mats.
Clean LH rear brake drum backing plates for 84-87 1 ton GM, some 88-91 R/V may be the same. These have the snap in style ebrake cables. Can be from 14 bolt FF SRW, DRW or Dana 70.
OEM 30/3500 Series Tailgate, Lights and Harness
Camper Special stuff, Tie downs, dual battery harness and relay(73-91 old style)
85-89 factory dual exhaust, any pieces, from carbureted truck.
Silverado 30 fender emblems with studs in tact (81-91 old style).
Scottsdale 30 fender emblems with studs in tact (81-91 old style).
Factory Under bed exhaust heat shields.
Rear spring shackles from 1973 +/- (folded with two rivets).
Doug Thorley Tri-Y headers for small block or big block.
OEM Front bumper guard (bumperette) for 81-87, passenger side.
SRW K30 OEM front hubcaps.
Harness, dual tank, upper, 87-91, TBI.
Rear frame rail tips from one ton pickup
Factory split tailpipe, cat and brackets from 87-88 one ton VIN R OR V

Re: Parting 1986 Suburban K20 4x4
 

Roof rack/rear air dam? thanks.

Re: Parting 1986 Suburban K20 4x4
 

engine crossmember?

Re: Parting 1986 Suburban K20 4x4
 

Hello are you still selling parts looking for a transmission cross-member for a 4x4 with 400
turbo and a 208 transfer case my tuck is a 1984 ?
My name is Dale and i can be reached at 704-865-1616 or by email

Re: Parting 1986 Suburban K20 4x4
 

This dude hasn't been on the forum in over a year.