How To: Ruin a Perfectly Good K/5
 

Well, I'm back in a Blazer after a short hiatus. Some of you may remember my former pale yellow '72 that was a 2wd conversion, How to: Ruin a perfectly good Blazer...

I started looking around for a replacement for it a few months back so the family can ride with and stumbled upon a Craigslist ad for a nice, original Highlander in Denver, CO for a great price. Talked a bit to the guy and decided I would fly out and pick it up. Unfortunately, by that time, someone local had snapped it up...

Fast forward a couple of weeks as my search continued and whattayaknow, the same Blazer pops back up, albeit at a much higher price. I tossed an offer at the guy, well below his asking price, and he countered reasonably.

Here's a couple of shots from the for sale ad:

Re: How To: Ruin a Perfectly Good K/5
 

It looked to be in very original, unmolested condition, but I wanted to get a closer look at some of the problem areas, as we all know how these things can look great on the outside, but be rotting from the inside out. Happily, the seller was willing to photograph anything I asked before I spent any time/money heading out to Denver.

A few interior shots from the ad:

Re: How To: Ruin a Perfectly Good K/5
 

After a bunch of back and forth with the seller, I was satisfied with the condition and decided to book a flight to Denver to finalize the deal in person. The guy thought I was crazy for wanting to drive a 40 year old truck across the country, but the way I see it, 40 years ago this is all people had :D So, I packed all the typical hand-tools into my checked luggage and so started the adventure...

The plan was to make it a two day drive, stopping halfway in Kansas. Unfortunately, I chose the worst possible time to try to drive out of Colorado. There was a little winter storm, Euclid, that blew in the night before I was set to leave. I made it all of 80 miles before the DOT shut down I-70 due to blizzard conditions.

Here's a shot the morning I left and one from the seedy motel I stayed in during the blizzard...

Re: How To: Ruin a Perfectly Good K/5
 

Very cool! I'm in...

Re: How To: Ruin a Perfectly Good K/5
 

I figured the worst was behind me after getting caught in a Blizzard on the first day of my trip, but little did I know, disaster was looming. An alternator bracket bolt managed to somehow shear itself off in the cylinder head somewhere just south of Wichita, KS. I managed to make a quick, roadside repair with some coat hangers I sourced at a truck stop and limped my way to a hotel. Next morning, I picked up some easy outs, a drill and an extension cord (the three things I didn't pack) and bolted the bracket up (in the hotel parking lot) with some grade 8 hardware and red thread locker. I didn't want them working loose again before I got home...

Re: How To: Ruin a Perfectly Good K/5
 

Thanks for tagging along :)

After I got the alt bracket fixed up, it was smooth sailing all the way home. Glad to be back in the south! Also glad to know that the choke and heater work when called upon :lol:

Re: How To: Ruin a Perfectly Good K/5
 

Following!
Posted via Mobile Device

Re: How To: Ruin a Perfectly Good K/5
 

The truck is really pretty clean and original, as the pics will illustrate. It is missing a few things here and there and needs some minor TLC, but what fun would it be if it didn't? The only major deviations from stock are the tires/wheels and a Tuffy locking console. I can live with that (or change it)...

Re: How To: Ruin a Perfectly Good K/5
 

Looks like a good find. Are you going to convert or keep it 4wd?

Re: How To: Ruin a Perfectly Good K/5
 

Welcome!

So, I was looking for a nice truck with the intention of converting it to 2wd, but I think this one might be too nice to do that to. Right now, I'm just tinkering with the little things that it needs to be reliable and comfortable to drive.

Today was alternator and battery replacement. I pondered doing the SI internally regulated alternator conversion, but couldn't bring myself to alter the stock wiring, so it got a rebuilt externally regulated unit with the original fan and pulley swapped on. Also wire-wheeled and painted the bottom of the battery tray. Couldn't resist a little rattle-can resto while I was at it :lol:

Re: How To: Ruin a Perfectly Good K/5
 

My original intent was to find one to convert, and do a step-by-step for the forum, but I'm not ready to go there with this one yet. It is NICE not having to use a floor jack to work underneath the truck--just grab the creeper and roll right under! The 4wd worked out pretty well when I, um... made my own exit to the frontage road to avoid a jack-knifed semi :D

Re: How To: Ruin a Perfectly Good K/5
 

Dang nice Blazer and one hell of a shakedown run! I'll be watching this one.

Re: How To: Ruin a Perfectly Good K/5
 

She's beautiful... Im considering the 2wd conv with my k5, but it's just a no frills stocker... I'll definately be watching tho!
Posted via Mobile Device

Re: How To: Ruin a Perfectly Good K/5
 

Nice find good luck with her . TUNED IN ALSO

Re: How To: Ruin a Perfectly Good K/5
 

Thanks- I figure after that, she's pretty much sorted out and we've become great friends :)
Thanks a lot- if I do convert, there will be details galore.
Thanks for tuning in- more to come :chevy:
Posted via Mobile Device

Re: How To: Ruin a Perfectly Good K/5
 

I'm in for the conversion!

Re: How To: Ruin a Perfectly Good K/5
 

I'm in.... love this Blazer!

Re: How To: Ruin a Perfectly Good K/5
 

Im in
Posted via Mobile Device

Re: How To: Ruin a Perfectly Good K/5
 

Lookin to see how you "ruin" it.....

Re: How To: Ruin a Perfectly Good K/5
 

Shortest build thread ever!!:lol:

Now that you have a nice finished 4wd...go find one of those down south k5s that are rusted from the bottom up about 12"......replace it all ,and convert to 2wd!:devil:

Re: How To: Ruin a Perfectly Good K/5
 

I'm in , whether you go low or high !!!!!! I'm Leaning more towards 4x4 though ,
Posted via Mobile Device

Re: How To: Ruin a Perfectly Good K/5
 

Very nice! Just my two cents keep it 4x4, you have a killer 2wd so that way you have the best of both worlds if needed.

Re: How To: Ruin a Perfectly Good K/5
 

X2
Posted via Mobile Device

Re: How To: Ruin a Perfectly Good K/5
 

Welcome
Some would say doing anything at all is ruining the originality...
Now that's funny. I travelled a long way to avoid major rust repair
Yeah, it's growing on me
Well, my killer 2wd is in Canada, so I gotta figure out what I wanna do with this one
Hm, I've already done a trailing arm swap on a 4wd frame- maybe I'll convert a LWB for Blazer use...
Posted via Mobile Device

Re: How To: Ruin a Perfectly Good K/5
 

So, after replacing the alt and batt, I was back charging again. Only now instead of 10.5v, I was seeing 15.5! I found a nice solid-state piece, a Wells VR715, that mimics the style of the original, but uses a circuit board instead of mechanical points--functions more like a modern alternator/regulator by shunting to ground instead of cycling on/off constantly.

Check out this piece of history I removed from the Blazer. Ah, the good old days when Sears was a trusted manufacturer of seemingly everything, instead of just another retailer...

http://i80.photobucket.com/albums/j1...0AAA6E3490.jpg

http://i80.photobucket.com/albums/j1...0AB92A4286.jpg

http://i80.photobucket.com/albums/j1...0AC0B500DC.jpg


Made in Korea, but looks right at home on the core support. Would this be considered 'ruining' it? :lol: Check out those chalk marks! :chevy:

http://i80.photobucket.com/albums/j1...0AC78C070A.jpg
Posted via Mobile Device

Re: How To: Ruin a Perfectly Good K/5
 

Looks awesome! I love that interior. No matter what you decide to do it'll be a nice truck. Although I prefer to see them on the ground:)
Posted via Mobile Device

Re: How To: Ruin a Perfectly Good K/5
 

I say keep it stock Its a great referance book. Love that Interior

Re: How To: Ruin a Perfectly Good K/5
 

Sorry, meant your truck not old blazer.

Re: How To: Ruin a Perfectly Good K/5
 

Thanks! The Highlander plaid makes this truck for me--would be easier to see the seats if it was slammed :devil:
Part of me agrees. I definitely need to get more pictures, if for nothing more than reference.
OIC. I have a truck? :lol: It is SO neglected right now--I should probably go drive it just to keep the battery charged...

Re: How To: Ruin a Perfectly Good K/5
 

X2! Just needs stock wheels and caps. You can never go backwards to "original".

Re: How To: Ruin a Perfectly Good K/5
 

The only thing I did to mine was a lift.New tires/rool bar/and a brush gaurd soon to be added

Re: How To: Ruin a Perfectly Good K/5
 

Good way to justify slamming it:metal:
Posted via Mobile Device

Re: How To: Ruin a Perfectly Good K/5
 

Haha! You are just like me, I can always find an excuse to modify my trucks. Even though I know I probably shouldn't:)
Posted via Mobile Device

Re: How To: Ruin a Perfectly Good K/5
 

Sweet rig! 4x4 or 2wd which ever way will be awesome.

Re: How To: Ruin a Perfectly Good K/5
 

I've thought about doing just that. Original gets just as many looks as custom.
Nice start there! I like the interior/color :)
Haha- yeah, why waste that good looking plaid on only the tall folks :lol:
That's part of the fun- imparting some of your personality on your vehicle.
Thanks! Still not sure how I'll ruin this one...

Re: How To: Ruin a Perfectly Good K/5
 

More tinkering. Found out I had a nice little leak at the upper corner of the windshield when it rained the other day...

I knew I was missing the drip deflectors (on order), but this leak was coming from a different area. Looking around, I found that there were no bolts in the visors holding the corners of the top down (!), hence the drippy-ness on the floorboard (and my leg). Grabbed a couple of stainless, 5/16-18 phillips screws, 2.5" long (thanks for the info, forum search!).

While I was at it, I also decided to replace the PO's ugly top hold-down hardware with something a little more 'correct' looking--at least to my eye. Not going for a concours resto here, but the hardware store bolts just were not doing it for me. Did a quickie polish on the stainless top hold-down strips, too. Much mo' betta now :chevy:

Re: How To: Ruin a Perfectly Good K/5
 

...and I had the 'posers' out together while I was moving cars around...

Re: How To: Ruin a Perfectly Good K/5
 

That was what i was talking bout, best of both. They look awesome together

Re: How To: Ruin a Perfectly Good K/5
 

Thanks! I thought it was kind of a cool pic
You guys got me thinking... I really like the look of BBrendal's Blazer on the 15x8s with dog dishes. I know Stockton Wheel makes these in up to 16x12 to accept factory hubcaps. Hmmmmmm...

Re: How To: Ruin a Perfectly Good K/5
 

I'm loving this blazer exactly how it is. BUT, if you still want a blazer to modify, and don't want the guilt associated with molesting this original, we can trade straight across. Trust me, there is no guilt in modifying this blazer. :lol:

[IMG]http://i1202.photobucket.com/albums/...s6-6-11001.jpg[/IMG]