Installing door wire boot/bellows
My truck did not come with power locks or power windows. I am going to drill the wire holes in the cab and the door, and install the rubber wire bellows.
I bought two new ones from LMC. One end of the bellows has a large opening, and the other end has a smaller opening. Does anyone know which side the larger opening goes to, the cab or the door? I've been to the junkyard to try and check this out and investigate other aspects of the PL/PW conversion, and the closest vehicles I could find were a few 88-91 Suburbans. Unfortunately, the bellows is riveted in place. Can't really get a drill in there without removing the door. Has anyone done this conversion before? |
Re: Installing door wire boot/bellows
I have done this several times. Carefully remove the doors, drill the holes, feed the wires thru and then carefully reinstall the doors. Use screws to remount the conduits (bellows). Its not that hard with a 4x4 and a floor jack. I did mine by myself. Be careful and don't drop the door. Clean up sharp edges or you will have issues.
|
Re: Installing door wire boot/bellows
Quote:
|
Re: Installing door wire boot/bellows
I think the big end goes on the door pillar as the factory wire harness goes thru a big bend at this point. It comes down the inside of the door jamb from the top and bends kind of 90 degrees to go thru the conduit. I used a large hole saw in the jamb with a smaller hole saw on the door. File edges smooth. You can rivet it shut but it makes access harder if you have wire issues. This is common in the jamb.
|
Re: Installing door wire boot/bellows
That makes sense, I'll go with that. Thanks.
Did you find that either the door or cab had dimple marks where to drill? I think I saw some on the door but I need to confirm that they match the hole spacing on the bellows. |
Re: Installing door wire boot/bellows
Yes the locations are already marked in the door jamb and I think on the door as well. Thats a very good point.
|
Re: Installing door wire boot/bellows
I took a closer look and some measurements of the dimpled drill points.
The dimples on the door are definitely right, the dimensions line up fine with the rubber bellows. The marks on the cab are a little weird. There's four holes, and the two outer ones do line up with the rivet holes in the door boot. The two inner holes seem to be spaced evenly between them. Not sure why there would be 4 holes? unless it's because the cab wire hole is larger and they had some special way of cutting it? Here's the door: https://i.imgur.com/oZBeoUsh.jpg Here's the cab: https://i.imgur.com/yfVriqRh.jpg Do the cab dimples look like what you've seen before? |
Re: Installing door wire boot/bellows
2 Attachment(s)
If you look inside the door, you'll see the same dimples! Not sure if the circle represents what size the actual hole should be.
Pictures: 1. Inner NOS door on my 79. 2. OEM door on the 78. Can't really see the dimples, but you can see the outline of the circle in both pictures. Thanks Mike |
Re: Installing door wire boot/bellows
1 Attachment(s)
You need to cut a 1.75” on the outside, then a 1.5” hole on the inside of the cab. I’ve done his quite a few times when converting from manual to power using my harnesses-it’s as close as you can get to how GM did it. I did my father in laws 77 GMC this way....
|
Re: Installing door wire boot/bellows
Thanks gmachinz, I was looking around that area wondering where wires would come through. Is the positioning of that hole critical or is it all open space within? On my drivers side plastic kick panel, it looks like there's a raised shroud for where the wires could come out and up but I'm not sure if that was the intended purpose, I'll get a picture later.
I did some measuring on the rubber bellows, looks like a 1.5 and 1.75 hole saw will be what I need, and I can use the 1.5 for the kick panel wire exit too. Has anyone else seen 4 dimples on the cab door jamb area like I am seeing? https://i.imgur.com/r3NMYgW.jpg |
Re: Installing door wire boot/bellows
Can't improve on whats been said. I can't remember if my door jambs had four dimples or not. But you are on the right track. Good luck.
|
Re: Installing door wire boot/bellows
1 Attachment(s)
Use the 1.75” on the outer first-when the bit goes just through to the inside panel-you’ll have a nice pilot hole to use the 1.5” from the cab interior side. I recommend drilling the 2nd dimple from the top-this way the wires go straight into the cab. Here’s my before pic:
|
Re: Installing door wire boot/bellows
Make sure to ream both hole edges really good-the metal is pretty thick there.
|
Re: Installing door wire boot/bellows
1 Attachment(s)
This is what the factory hole in the piller looks like,
|
Re: Installing door wire boot/bellows
Excellent! Not sure what process they used to cut the hole at the factory, but the oval hole at least somewhat explains why there's 4 dimples in the cab instead of just three.
I think I can get away with center punching between the outer holes and then using a 1.75 hole saw. |
Re: Installing door wire boot/bellows
The last detail is the kick panel hole. The location gmachinz posted seems lower than what the factory did, but probably makes it easier to route wires through the bellows. Maybe less strain on the wires too since they stay straighter
I found these pictures that show the wires coming out closer to the dash. It looks like GM placed the wires in the molded area in the kick panel cover where the fresh air vent pull handle would go. https://i.imgur.com/IXtRC8E.jpg https://i.imgur.com/EFU8TF8.jpg I'm not sure if I can get the drill that close to the dash to cut the hole in the factory location. |
Re: Installing door wire boot/bellows
Last weekend I took both doors off, cut the holes, and got the bellows installed on both sides. Thanks to everyone that contributed here. I still need to cut the kick panel holes, but once I do that I will start another thread as a how-to so that all the information contributed here and my experiences will be in one place and easy to find.
|
Re: Installing door wire boot/bellows
Did you ever start another thread ,I,m going to do this some time this year
|
Re: Installing door wire boot/bellows
Quote:
|
Re: Installing door wire boot/bellows
I'll be adding the bellows to my 85 this weekend. In fact, the parts are roaming my neighborhood on a FedEx truck as I type this. I'll try to document the process and post pics here as well.
|
Re: Installing door wire boot/bellows
2 Attachment(s)
I was able to grab this pic with my camera phone since I have the door stripped. You can clearly see the area that needs punched out for the bellows. My dimples weren't very noticeable on my door so I poked around with a 1/16th bit and then opened it up with a step bit. I'm going to install rivnuts instead of the rivets so I can easily remove the bellows when needed without having to drill out rivets in a door jamb. More to come tomorrow.
|
Re: Installing door wire boot/bellows
The factory had the luxury of using a shear punch to create a nice smooth oval-but on manual cabs this isnt an option-even using a step bit its a pita because there are 2 layers of metal to go through on the outer side and they arent welded together very well. You must seal the harness with a grommet on the inner kick surface which means the outer hole must must slightly larger so that a grommet can easily pass through. This means 2 things:
1.) Drilling straight through to keep the travel straight and: 2.) DO NOT use a step bit but instead a hole saw I used a fine tooth hole saw to create a 1.75” on the outside and a 1.5” hole on the inside. |
Re: Installing door wire boot/bellows
1 Attachment(s)
Here’s what I came up with.
|
Re: Installing door wire boot/bellows
gmachinz where did you find the rubber grommets for the inside?
Rick |
Re: Installing door wire boot/bellows
what does the door to pillar gap look like?
I need to run wires in my '76 doors. |
Re: Installing door wire boot/bellows
curious also about the inner grommets, looking to add remote power locks to mine soon
|
Re: Installing door wire boot/bellows
New door bellows $80 ouch U.S. that,s about $120 Can.
|
Re: Installing door wire boot/bellows
1 Attachment(s)
Quote:
I paid a whopping $12.95 per side. LMC |
Re: Installing door wire boot/bellows
I checked yesterday and was 77.00 or so. Better re-check ,thanks. Might have not been LMC, just did a quick Google search
|
Re: Installing door wire boot/bellows
I must of clicked on the wrong pic,did a search on images and clicked the photo It was a e-bay ad https://www.ebay.com/itm/2-Qty-Door-...-/312146248448
|
Re: Installing door wire boot/bellows
That seller needs his head adjusted. But, there are people who are too lazy to look around a little and end up paying way more than something is worth. It's different when it's something that's in high demand.
|
Re: Installing door wire boot/bellows
I was in a hurry to see and I saw classic on the page and didn,t read it all and thought classic industries. Always search for stuff 2 minutes before you have to go to work, lesson learned
|
Re: Installing door wire boot/bellows
is it possible for someone to grab the measurements for installing these bellows on early doors/cab that don't have the divots?
|
Re: Installing door wire boot/bellows
1 Attachment(s)
I recently did this to a non factory pwr window door.
|
Re: Installing door wire boot/bellows
Quote:
|
Re: Installing door wire boot/bellows
Quote:
|
All times are GMT -4. The time now is 02:35 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com