62 Burb project in the making.
 

My 62 Suburban project is starting I bought it last year and finally got it.
Will try to keep pictures updated.
Going to start on removing I 6 tomorrow.
Got the 283 all set waiting to go in,PB and new hyd.clutch.

Re: 62 Burb project in the making.
 

Does it have a jump seat on the passenger side? How cool!

I hope you keep that Wurden Fire Dept. emblem on it :)

B

Re: 62 Burb project in the making.
 

Yes the jump seat folds down to make a bench like seat as well.
It looks like it was used as an ambulance as well.
I am probably going with the Fire dept. lettering again when finished which is quite a ways off for paint.

Re: 62 Burb project in the making.
 

Making a little progress. 6 is out measuring for the 283. & New tank.

Re: 62 Burb project in the making.
 

Few pictures as well.

Re: 62 Burb project in the making.
 

Do you have a front saddle mount for the 283?

Re: 62 Burb project in the making.
 

Hi John, No I am using 67-72 mounts on the side. Already removed the front mount, makes it easier down the line if I decide to do a 355. Have lots of parts from the race car that may get used later on. We run a super gas car when we are not rebuilding old trucks. Right now the only racing is with one of the teams kids Jr. Drag race.

Re: 62 Burb project in the making.
 

OK, those are better yet. I didn't know what parts you had to work with but it sounds like you have some parts plus a bit of experience as well.

Re: 62 Burb project in the making.
 

Got the motor mounts done. Dident like the idea of putting the 1" block under the top support to the frame so we did a little remodeling, 2 notches out of the side at the bends and bend together after a few fitting trys welded it back together cut off the top bolt holes and made new holes. Fits great and looks original I will get some installed pictures in later we want to try and put the engine in today hopefully.

Re: 62 Burb project in the making.
 

I had a 73-81 Blazer tank in my 65 Suburban several years ago. I fit perfect in the original home. I just had to modify the filler tube a little, and find a fuel guage that would work with it.

Re: 62 Burb project in the making.
 

What kind of fuel gauge did you end up with?
That is basically what I am doing.
Added a crossmember to adjust where the supports go an fits perfect.

Re: 62 Burb project in the making.
 

Thought we could put the engine in today but ran into a snag.
The Novak hydraulic clutch slave cylinder setup needs to have a long throw out bearing so I need to get that before putting the engine in as we want to adjust it on the floor.

Re: 62 Burb project in the making.
 

I never got a gauge put in. I knew how far I could go on a tank so would fill it before it ran out. The 73-81 use a different ohm than the stock. I tried to use a gauge from those years and cut down the backing but didn't work. As far as the support, I actually removed on to fit the tank in. I will try to find the pic of it in, from underneath and post it later.

Re: 62 Burb project in the making.
 

Here are the pics. Sorry they aren't that clear.

Re: 62 Burb project in the making.
 

Interesting to see the original tank. Mine had a curved tank to make room for the spare tire. But the shipping company butchered that one.

Re: 62 Burb project in the making.
 

Working on the brakes with the kit from capt.fab.

Re: 62 Burb project in the making.
 

[QUOTE=sirJim;7976192]Interesting to see the original tank. Mine had a curved tank to make room for the spare tire. But the shipping company butchered that one.[/QUO
My spare is laying on the floor inside. I have a bracket that screws to the sidewall when I don't have the big 2nd seat in. It's something the original owner made.

Re: 62 Burb project in the making.
 

Finally got the engine in.

Re: 62 Burb project in the making.
 

A little more progress after a weeks vacation with the family. Belt on windshield out and painted the windshield channel which was in excellent shape.

Re: 62 Burb project in the making.
 

Little progress. Finally got the longer throw out bearing and Got the transmission and drive line in. Novak slave cylinder mounted still need to put the lines in and adjust but on its way.

Re: 62 Burb project in the making.
 

We got a bit of wiring done last night.
Carb installed, Radiator off to have the thermostat switch bung welded in for the electric fan.
Have to do a make shift exhaust in the first stages to get it thru DMV, look at doing it right down the road.:mm::mm:

Re: 62 Burb project in the making.
 

One with the carb in.

Re: 62 Burb project in the making.
 

Got the fan in.

Re: 62 Burb project in the making.
 

Exhaust is in for a try.

Re: 62 Burb project in the making.
 

Nice work on the exhaust :thumbs: