1966 LS swap info
Hey all, I am looking to put a 5.3 LS in my '66 SWB, but not sure which tranny yet. Either the 4L60E or 6L80E (the latter is the same as my 2011 GMC Sierra). With either of these transmissions, will there be any clearance issues with a standard hump transmission tunnel on my '66 cab? I know when using the Porterbuilt dropmember kits, they raise the motor/tranny up so a high hump tunnel is required. However I will be using the stock crossmember with an LS motor mount kit, so not sure if that raises the motor/tranny any? Hopefully I won't need to install a high hump tunnel in order to do the swap.
Also, my truck is on airbags so it sits pretty low when aired out. With an LS in there, will the oil pan be the lowest part of the front end? Currently the lower control arms are the lowest point on my truck in the front. They touch the ground when aired out all the way. I am hoping that with an LS swap the LCA's will still be the lowest point. Thanks in advance! |
Re: 1966 LS swap info
The 4L60E will clear without issue.
If you're running a stock LS truck oil pan, it will sit ~1" lower than the engine crossmember...depending on which mounts you run. |
Re: 1966 LS swap info
In my 66' I used 4L60E with standard hump tranny tunnel with no clearance issues. I used a f body ls oil pan.
|
Re: 1966 LS swap info
thanks for the confirmation guys! Does anyone know if the 6L80E will clear?
|
Re: 1966 LS swap info
Without changing the oil pan from stock to a "hot rod pan" your oil pan will be the lowest, sticks out about 1-1.5" lower
|
Re: 1966 LS swap info
4L80e and 6l80e will both require tunnel modifications. Ive not seen many trucks our body style with 6L80s though. I know 4l80e require tunnel hump modifications
|
Re: 1966 LS swap info
ok thanks Zach. I will likely go with the 4L60E anyways but just getting as much info as I can.
|
Re: 1966 LS swap info
The pcm must come from a truck with a 6l80 trans, I don't think the 6l80's are as big as the 4l80 though. Anybody know how big the 4l80 is? I'll take some measurements of the 6l80 Saturday.
|
Re: 1966 LS swap info
I have not made an exact comparison but a 4L80E should not be any 'bigger' than a TH400 as far as tunnel clearance is concerned. The 4L80E is just longer. I installed a TH400 in my '66 Suburban with a low trans hump. But I did move the engine and trans froward 2".
|
Re: 1966 LS swap info
thanks all! do I also need a special gas pedal to work with an LS motor? Or can you retrofit a stock pedal to work? can you also use the stock gauges (speedo, temp etc.) or do you have to upgrade to electronic gauges?
|
Re: 1966 LS swap info
A 67-72 pedal assy works very well and is reasonable too.
Gauges will need to be updated to electronic. Check out the LSx section here and the FAQ's for specifics. |
Re: 1966 LS swap info
3 Attachment(s)
Quote:
I know the DBW can definitely be adapted to work with the stock pedal...with a little ingenuity. |
Re: 1966 LS swap info
Quote:
|
Re: 1966 LS swap info
It matters on how your motor is mounted to.
|
Re: 1966 LS swap info
I was told by someone else that You can run the stock gas pedal if you use a cable style throttle body rather than the fly by wire type. Is that true?
|
Re: 1966 LS swap info
Quote:
Unfortunately no, our trucks have linkage type accelerator and not cable like the DBC LSx throttle body. |
Re: 1966 LS swap info
Gotcha, thanks Clyde!
|
Re: 1966 LS swap info
is it possible to use my stock gas tank?
|
Re: 1966 LS swap info
You should be able to use your stock gauges, I do in my ‘51.
Dakota digital makes an adapter for the speedo http://www.dakotadigital.com/index.c...rod/prd886.htm I also use the stock temp gauge and oil pressure, it works great and I will do the same in my ‘64 Suburban if I can ever get to working on it. |
Re: 1966 LS swap info
I was told I can use my stock tank if I have a return line running to it. What is the best way to add a return line to the stock tank?
|
Re: 1966 LS swap info
You will want to use your current supply line for your return line. then add your new larger supply line thru the sending unit flange. I know there are a couple builds on here with either a LS or earlier EFI conversion that have done this.
|
Re: 1966 LS swap info
Thanks Captain I will search around for those build threads!
|
Re: 1966 LS swap info
2 Attachment(s)
As stated, the placement of the engine determines the tunnel clearance, ground clearance and driveshaft U-joint angles.
Here is a 6L80E in my '62. It does not clear the low trans hump. For reference, the angle iron is approximately 4 1/2" inches above the floor. The second picture shows the GM "Hummer" oil pan is still higher than the front cross member. This engine position is with a 1979 front cross member, stock 79 motor mounts and home made trans mounting bracket. |
Re: 1966 LS swap info
Thanks Soyuz. As everyone is stating, where the motor is mounted will determine clearance. I am looking for a bolt on motor mount for LS swaps. I know there are a bunch of different ones. Does anyone know of a bolt on set that sets the motor to where it will clear with the 4l80e? What motor mounts are typically recommended with my application?
thanks guys for all the info, this is all new to me! |
Re: 1966 LS swap info
Here is one of those threads I was thinking about.
http://www.67-72chevytrucks.com/vboa...=641267&page=4 Do you realize that there is a LS swap section of this forum that likely has all the info you are looking for? Quote:
Quote:
|
All times are GMT -4. The time now is 12:03 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com