|
Project: 65 C-10
I have been workin on my 65 C-10 for about a years time now... The frame has been z'd 4 inches and the cab mounts have been lowered an inch. The rear is notched with the factory trailing arms repostitioned. recently I have shaved the firewall and just doing minor work to the cab.. New inner rockers, rockers, and cab corners... I hope to set the cab on the frame within the next few weeks.. maybe over Christmas break Let me know what all of you think about it..
http://i123.photobucket.com/albums/o...5/P2270028.jpg Tranny crossmember http://i123.photobucket.com/albums/o...5/P2160001.jpg http://i123.photobucket.com/albums/o...5/P1200016.jpg http://i123.photobucket.com/albums/o.../StockPass.jpg http://i123.photobucket.com/albums/o.../Pass.Hole.jpg http://i123.photobucket.com/albums/o.../GapFilled.jpg http://i123.photobucket.com/albums/o...65/Bracket.jpg http://i123.photobucket.com/albums/o...GapFilled4.jpg http://i123.photobucket.com/albums/o...5/P8030026.jpg Sorry about so many pics just wanted to let everyone know where I am at on this project..... Let me know what you think about everything... |
Re: Project: 65 C-10
bad ass man. Nice work.
|
Re: Project: 65 C-10
Looking good. I like that you added reinforcment to the front Z behind the motor. I have seen to many that just plate the out side and leave it at that. What did you do for the very front? Lets see some more pics. I just picked up a 63 so I am looking for all the pics I can get.
Kevin LFD inc. |
Re: Project: 65 C-10
The very front was cut and I cut a 8 inch piece of strap to hold everything back together...
http://i123.photobucket.com/albums/o...5/P3100012.jpg http://i123.photobucket.com/albums/o...5/P3100010.jpg http://i123.photobucket.com/albums/o...5/P3020046.jpg http://i123.photobucket.com/albums/o...5/P2240020.jpg http://i123.photobucket.com/albums/o...5/P1200009.jpg We flipped the frame over and smoothed the bottom side of the plating also.. http://i123.photobucket.com/albums/o...5/100_0583.jpg |
Re: Project: 65 C-10
very nice:metal::metal::metal:
|
Re: Project: 65 C-10
:agree: that thing looks great so far.
|
Re: Project: 65 C-10
Looks like it's almost time to throw some sheetmetal on it!:metal:
|
Re: Project: 65 C-10
That seriously looks like its been very time consuming, but it will be 100% worth it in the end. That '65 is going to be badass
|
Re: Project: 65 C-10
Nice work. You should post this over on the 60-66 forum.
|
Re: Project: 65 C-10
Thanks for the comments guys... The frame has sat outside all summer and fall so Ineed to bring it in and clean it up and paint it again.. Inside the framerails and all.. Have to put a rear cab mount on the cab and then I will be setting it on the frame... I dont get too much work done to it.. I am in college and reallly dont have the time to mess with it too much but I try as much as I can.... Thanks for the comments it gets me motivated...
|
Re: Project: 65 C-10
Nice progress. That firewall is going to make a huge difference. Keep the pics coming.
|
Re: Project: 65 C-10
I really hope the firewall helps a lot. It was a lot of work.... Could one of the administrators put this thread in the 60-66 forum? If one could do that I would really appreciate it
|
Re: Project: 65 C-10
Nice job.You got some work done.Can't wait to see more progress pics.
|
Re: Project: 65 C-10
I got my rear cab mount in yesterday so I hope to roll the cab on its back and pu tit in this week... then set the motor and tranny in and set the cab on, cut the tranny and driveshaft tunnel, raise it to where it needs to be, tack it up, pull the cab back off and weld it up good.... after that the cab we be on for good
Thanks for the commentsguys |
Re: Project: 65 C-10
Worked on the cab new inner rockers, rockers, cab corners.
http://i123.photobucket.com/albums/o...5/P9230010.jpg http://i123.photobucket.com/albums/o...5/P9230005.jpg http://i123.photobucket.com/albums/o...5/P9230004.jpg http://i123.photobucket.com/albums/o...5/P9230003.jpg http://i123.photobucket.com/albums/o...5/P9230002.jpg |
Re: Project: 65 C-10
Looks good! I look forward to starting my 63 GMC and getting it down to bare metal. I love how they look in the nude!
Kevin LFD Inc. |
Re: Project: 65 C-10
Thats gonna be one bad ride...
|
Re: Project: 65 C-10
Quote:
|
Re: Project: 65 C-10
Quote:
|
Re: Project: 65 C-10
For Sure
|
Re: Project: 65 C-10
Well finally rolled the frame back in.. I got my bushings yesterday..
http://i123.photobucket.com/albums/o...5/PA120038.jpg http://i123.photobucket.com/albums/o...5/PA120038.jpg http://i123.photobucket.com/albums/o...5/PA120036.jpg http://i123.photobucket.com/albums/o...5/PA120033.jpg Also I did some work on the doors while I was waitin on the cab bushings.. Before http://i123.photobucket.com/albums/o...5/PA100020.jpg http://i123.photobucket.com/albums/o...5/PA100022.jpg After.. http://i123.photobucket.com/albums/o...5/PA120035.jpg http://i123.photobucket.com/albums/o...5/PA120034.jpg Lots more progress in the next few weeks..... Thanks for lookin guys |
Re: Project: 65 C-10
Lookin good!
|
Re: Project: 65 C-10
Slmd92DIME, what part of WV do you live? I'm near Roanoke. And, I see you're online now (2:45 AM) what's up with that? I've got an excuse, I'm at work.
|
Re: Project: 65 C-10
looks killer!! man that door was solid bondo!
|
| All times are GMT -4. The time now is 10:43 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com