Check it out
 

SO WHAT DO YOU THINK ?
I JUST RECENTLY FINISHED THE 2 LINK, MOUNTED THE 31GAL TANK FOR MORE CLEARENCE, AND ROUGHED IN THE BODY WORK ENOUGH FOR ITS FIRST COAT OF PRIMER.

BEFORE...
http://i657.photobucket.com/albums/u.../BLAZING/3.jpg

AFTER...
http://i657.photobucket.com/albums/u...BLAZING/19.jpg

http://i657.photobucket.com/albums/u...BLAZING/18.jpg

http://i657.photobucket.com/albums/u.../FUELTANK6.jpg

ANYONE HAVE ANY IDEAS ON HOW TO GET THE FRONT A LITTLE LOWER?

Re: Check it out
 

Dropmember:metal:

Re: Check it out
 

Yea I know i checked it out but i just got laid off and unemployment doesn't pay that good. I just might have to wait for next years tax returns.
Nice Blazer by the way!

Re: Check it out
 

you could always do a Z

Re: Check it out
 

looks good man i would do the crossmember

Re: Check it out
 

What do you have in front now?

Re: Check it out
 

Thanks Guys
3" DJM spindle w/ Firestone 2600 bags w/ plates up top and cups down below. I was thinking about cutting the cups just a little to maybe get an inch.
Would control arms help?

http://i657.photobucket.com/albums/u...BLAZING/11.jpg

http://i657.photobucket.com/albums/u...BLAZING/41.jpg

Re: Check it out
 

oh yeah, cut the cups for sure!

Re: Check it out
 

remove you cups and cut in some 8" pipe
I used a 2.5" piece lays on crossmember and misses heater box by .5"
I also have 3" belltec spindles with a upper bag plate like your
I'm running 255/70/15 on a 8" rallie
http://i37.photobucket.com/albums/e9...r29_0002-1.jpg

on my burb I went from this
http://i37.photobucket.com/albums/e9...Apr05_0004.jpg

to this
http://i37.photobucket.com/albums/e9...Apr30_0001.jpg

hope this helps cost me $150 for the metal and having it welded in

Re: Check it out
 

How much do you think I should cut off?
Do you know of anyone who has used plates on the lower control arms like these do you think these would help?

Re: Check it out
 

Did you have any issues with camber or any other suspension issues by doing this?
I wouldn't have to worry about heater box

http://i657.photobucket.com/albums/u...BLAZING/30.jpg

Re: Check it out
 

Looks good! Cut 1" off, that is what I did but do not cut any more then that you could rub your bags..

Re: Check it out
 

Thanks tvblazer I think i'll try that first.

By the way man love yor blazer mine will also be BLACK, that was the original color but my interior will be RED

Re: Check it out
 

post a pic to compare
looking good how did the rear sheet metal turn out
how much did you raise the gas tank

Re: Check it out
 

Thanks man!

Red and black pops!

Re: Check it out
 

I havent finished the floor yet I'm planning on cuting the inside of the bedsides and moving it up to where the tubs are about an inch from the bed rails, that way I can bolt the tubs up just incase i need to remove them in the future for something. I will post pics as soon as I get to that.
I will take som measurement of the tankand let you know, but I did have to remove the crossmember gas tank support just behind the axle and clearenced the tank supportat the rearundr the tailgate. I'll post some pics for u.

Re: Check it out
 

Doesn't that diff need a panhard bar? How will it keep from going side to side?

Re: Check it out
 

could u post some pics of the 2 link,thanks

Re: Check it out
 

Nice job, I look forward to watching your progress. I'm just about to smooth my firewall, hopefully this weekend.

Re: Check it out
 

I need to mock up the motor and trans first to get the pinion angle correct.

Re: Check it out
 

It's a lot of work they wernt very straight from the factory to begin with, Good Luck!

Re: Check it out
 

http://i657.photobucket.com/albums/u...LAZING/SR4.jpg

http://i657.photobucket.com/albums/u...AZING/SR11.jpg

made the bars from 1.5"O.D x .25wall DOM (Expensive)
Bag brackets are from suicidedoors

Re: Check it out
 

do those bars have a pivot on each end?

Re: Check it out
 

yes in the front of the bar it has urethane replacment bushings, or i could use stock replacement. The rear of the bar has large heim joint, i wanted to be able to adjust it if needed. I still haven't installed the suicidedoors pan hard bar. I tested the system and it travels fine without any binding

Re: Check it out
 

I like that, looks simple. How are you going to run your shocks?