The 1947 - Present Chevrolet & GMC Truck Message Board Network

The 1947 - Present Chevrolet & GMC Truck Message Board Network (https://67-72chevytrucks.com/vboard/index.php)
-   General Discussion (https://67-72chevytrucks.com/vboard/forumdisplay.php?f=15)
-   -   Step one ... grab a skanky old office chair (https://67-72chevytrucks.com/vboard/showthread.php?t=789112)

CG 06-23-2019 12:32 PM

Step one ... grab a skanky old office chair
 
4 Attachment(s)
So the flag/banner/embroidery business next door is moving. They had a ton of stuff they were tossing. I’ve been on the lookout for a decent roll around stool to use when I’m at the office doing shop work (copier/printer) service and sales. Grabbed three old skanky looking roll around office chairs they were tossing. I like em because they adjust up and down.

First remove and toss the back.

Second remove the wheels and dig out all of the entangled thread.

Third remove all the base parts

Last staple some old scrap vinyl over the skanky seat and reassemble

Whaalaaa! I nice adjustable roll around work stool.

mongocanfly 06-23-2019 01:29 PM

Re: Step one ... grab a skanky old office chair
 
Thatll work!..

Palf70Step 06-23-2019 02:50 PM

Re: Step one ... grab a skanky old office chair
 
Nice!!

Stocker 06-23-2019 03:10 PM

Re: Step one ... grab a skanky old office chair
 
Great idea!

shifty 06-23-2019 04:06 PM

Re: Step one ... grab a skanky old office chair
 
Did the same with a chair at my wife's building, but used the round wooden top from a crappy barstool I found at the curb on trash day that seemed to be virtually unused.

Those casters on the older chairs (new ones are all plastic) make for good creepers. Not very low-profile, but if your truck is tall enough, it works fine.

Getter-Done 06-23-2019 04:13 PM

Re: Step one ... grab a skanky old office chair
 
Nice work.






.

special-K 06-24-2019 07:20 AM

Re: Step one ... grab a skanky old office chair
 
It won't work until you put the word "CRAFTSMAN" across the seat in white letters.

blazer2007 06-24-2019 08:56 AM

Re: Step one ... grab a skanky old office chair
 
I use the wheel base and put a pole and a light in the hole and then I have a roll around shop light

67ChevyRedneck 06-24-2019 10:41 AM

Re: Step one ... grab a skanky old office chair
 
I just had a flashback to cutting all my wife's hair out of our vacuum :lol:

That's pretty sweet, and the dirt/oil/grease will wipe off the vinyl (for the most part anyway).

Grumpy old man 06-24-2019 12:28 PM

Re: Step one ... grab a skanky old office chair
 
1 Attachment(s)
:lol: Here's mine !

This is the first stage of getting old ! Why kneel on the floor cutting and welding when you can sit down ? :lol: It's a lot easier to get back up and if you can't then you just roll into the house and slide into the recliner . :lol:

CG 09-14-2019 01:21 PM

Re: Step one ... grab a skanky old office chair
 
1 Attachment(s)
Did another one, tis the season ....

special-K 09-16-2019 07:42 AM

Re: Step one ... grab a skanky old office chair
 
Do another and sell it to the tailgaters

Ol Blue K20 09-16-2019 08:11 AM

Re: Step one ... grab a skanky old office chair
 
I hope you get a matching tv tray for snacks while you watch the game.


All times are GMT -4. The time now is 09:41 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com