The 1947 - Present Chevrolet & GMC Truck Message Board Network - View Single Post

Marv D · 05-23-2016, 07:58 PM

Along with putting the 66 truck back to a street driver and putting it up for sale,, I decided I'm done. Going to sell the other hotrod too. Thought I'd put it in here for you guys to pass along if you know anyone looking for a turnkey bracket car.

$28,500 is more than fair and if you want to haggle. lets start at $45k and you can beat me down to $30k and we'll call it good. (I don't play that BS game very well) $28,5 is fair and the price.

It's a all steel (except hood, trunk deck and floor) 64 Chevy II tube chassis car.
2885 pounds with glass, front window operators and steel bumpers at both ends. and goes 6.6's in 6500' air

Normally aspirated 434 small block single dominator
(Motown block Olivers rods, Scatt prolight crank JE pistons, a set of Bishcoff / Uratchko built 23° AllPro 245 RR heads, SuperVictor, Prosystems dominator, Jay Allen cam, .795 / .810 lift, Gilbertson 10qt pan, Lemons headers, Aerospace vacuum pump and mandrel, Mallory 250 alcohol pump and regulator (motor made 797HP on a Superflow engine dyno tuned on C-14)

MSD digital 7 (7530T box) with matching Ecore 7 coil (software included)

4link had new CM rod ends 2 years ago, Kino aluminum double adjustable rear coilovers, AJE strut front chassis with Strange struts / R&P

Rear is a early Mustand 9" housing (small bearing ends) and 31spline MarkWilliams axles, MW Antiroll kit , Strange aluminum centersection / Strange HDspool with Richmond Pro gears. MW chromeMoly driveshaft with 3150s at both ends. Chassisworks wheelie bars

Mildsteel chassis with current 8.50 cert (set up for 180-220 pound (5.10" driver)

True WELD Magnum 2.0DRAG wheels all around, Aerospace rear disks / Willwood dual piston caliper disks on the front. (new never mounted 14x32 Hoosiers for the rear and CHassisworks "whishbone locator" ready to install included)

Dedenbear SFI case / Hughes Top Sportsman, Hughes converter (will need recert next year) Collector Tethers, Sportsman diaper, everything the safety Nazi's demand is current, but trans and chassis cert will need to be re-certed next year.

Will EASILY go 1.35 sixty on a tight track. Runs 9.35's at 2500', 9.60's at 6000', went 9.14 in 400' air.

Data logging with a older Edelbrock QuickData. 16 channel
currently logging /sensors for:
Engine RPM
driveshaft RPM
Oil pressure
oil temp
coolant temp
EGT in 2 tubes (bungs in all 8)
Innovate WB O2 in both collectors
Fuel Pressure
Transbrake on/off

Aerospace air shift, air chute release, Dedenbear CC3 delay box.

We won't tell the wife but I have the folder with receipts for all $40'k invested in this thing to get it to this point,, part #'s dyno sheets and everything but someone to sit in the seat and grin is included.

Know were truck guys here but if you know someone looking for a turnkey car send em my address please. My NHRA competition license expires in Jan next year and looking to be out of the 9 orgasm's before then.

05-23-2016, 07:58 PM	#1
Marv D Registered Truck Offender Join Date: May 2008 Location: hells training ground (aka Ariz) Posts: 3,118	welp, I guess it's time Along with putting the 66 truck back to a street driver and putting it up for sale,, I decided I'm done. Going to sell the other hotrod too. Thought I'd put it in here for you guys to pass along if you know anyone looking for a turnkey bracket car. $28,500 is more than fair and if you want to haggle. lets start at $45k and you can beat me down to $30k and we'll call it good. (I don't play that BS game very well) $28,5 is fair and the price. It's a all steel (except hood, trunk deck and floor) 64 Chevy II tube chassis car. 2885 pounds with glass, front window operators and steel bumpers at both ends. and goes 6.6's in 6500' air Normally aspirated 434 small block single dominator (Motown block Olivers rods, Scatt prolight crank JE pistons, a set of Bishcoff / Uratchko built 23° AllPro 245 RR heads, SuperVictor, Prosystems dominator, Jay Allen cam, .795 / .810 lift, Gilbertson 10qt pan, Lemons headers, Aerospace vacuum pump and mandrel, Mallory 250 alcohol pump and regulator (motor made 797HP on a Superflow engine dyno tuned on C-14) MSD digital 7 (7530T box) with matching Ecore 7 coil (software included) 4link had new CM rod ends 2 years ago, Kino aluminum double adjustable rear coilovers, AJE strut front chassis with Strange struts / R&P Rear is a early Mustand 9" housing (small bearing ends) and 31spline MarkWilliams axles, MW Antiroll kit , Strange aluminum centersection / Strange HDspool with Richmond Pro gears. MW chromeMoly driveshaft with 3150s at both ends. Chassisworks wheelie bars Mildsteel chassis with current 8.50 cert (set up for 180-220 pound (5.10" driver) True WELD Magnum 2.0DRAG wheels all around, Aerospace rear disks / Willwood dual piston caliper disks on the front. (new never mounted 14x32 Hoosiers for the rear and CHassisworks "whishbone locator" ready to install included) Dedenbear SFI case / Hughes Top Sportsman, Hughes converter (will need recert next year) Collector Tethers, Sportsman diaper, everything the safety Nazi's demand is current, but trans and chassis cert will need to be re-certed next year. Will EASILY go 1.35 sixty on a tight track. Runs 9.35's at 2500', 9.60's at 6000', went 9.14 in 400' air. Data logging with a older Edelbrock QuickData. 16 channel currently logging /sensors for: Engine RPM driveshaft RPM Oil pressure oil temp coolant temp EGT in 2 tubes (bungs in all 8) Innovate WB O2 in both collectors Fuel Pressure Transbrake on/off Aerospace air shift, air chute release, Dedenbear CC3 delay box. We won't tell the wife but I have the folder with receipts for all $40'k invested in this thing to get it to this point,, part #'s dyno sheets and everything but someone to sit in the seat and grin is included. Know were truck guys here but if you know someone looking for a turnkey car send em my address please. My NHRA competition license expires in Jan next year and looking to be out of the 9 orgasm's before then. __________________ Still playin with trucks, even at my age! When you're dead, it's only a problem for the people around you, because you don't know you're dead. .....It's kinda the same when your STUPID. I just did my taxes and reviewed my SS statement. Thanks to the current administration it looks like I will only have to work till noon on the day of my funeral. Last edited by Marv D; 05-23-2016 at 08:06 PM.