Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
04-06-2018, 04:58 PM | #1 |
Registered User
Join Date: Dec 2011
Location: Yuma Arizona
Posts: 1,526
|
Squares w 2-piece driveshaft
Looking for info on a 2-piece driveline setup. I need to go that route after a trans/t-case swap in my 85 longbed. Any pics w/o the bed or underneath would be great. Looking to see how the carrier bearing is mounted and if it's on a bracket or a separate x- member.
Thx in adv. |
04-06-2018, 06:57 PM | #2 |
Post Whore
Join Date: May 2015
Location: Alabama
Posts: 14,657
|
Re: Squares w 2-piece driveshaft
the one on my truck is mounted on its own crossmember...
__________________
Mongo...aka Greg RIP Dad RIP Jesse 1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598 Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334 Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563 2023 Chevy Z71..daily driver |
04-06-2018, 07:13 PM | #3 |
Registered User
Join Date: Dec 2011
Location: Yuma Arizona
Posts: 1,526
|
Re: Squares w 2-piece driveshaft
Is it the same height as the t-case output shaft? Does that first shaft run parallel to the ground? Where does the slip yoke go? Sorry for all the questions. This was an issue o hadn't thought about until the 11th hour.
|
04-06-2018, 07:24 PM | #4 |
Registered User
Join Date: Mar 2015
Location: South of Pittsburgh
Posts: 428
|
Re: Squares w 2-piece driveshaft
On our 79 c30 the slip yoke is the rear shaft to front shaft.
Our carrier bearing is almost directly at the back of the cab. Yes front shaft runs parallel. All the angle is in rear shaft I can prolly get pics tomorrow if you need em |
04-06-2018, 07:25 PM | #5 |
Post Whore
Join Date: May 2015
Location: Alabama
Posts: 14,657
|
Re: Squares w 2-piece driveshaft
the slip joint in mine is at the hanger bearing..the spline section of ds goes thru the hb....there is a little down angle on the first section of ds to hb,,but not much...from hanger to rear diff the ds is down angle as well....mines 2wd,not 4wd , but the same applies to both...is your missing?
__________________
Mongo...aka Greg RIP Dad RIP Jesse 1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598 Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334 Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563 2023 Chevy Z71..daily driver |
04-06-2018, 07:26 PM | #6 |
Post Whore
Join Date: May 2015
Location: Alabama
Posts: 14,657
|
Re: Squares w 2-piece driveshaft
maybe thisll help...it has some ds and hb pics...http://67-72chevytrucks.com/vboard/s...d.php?t=677974
__________________
Mongo...aka Greg RIP Dad RIP Jesse 1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598 Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334 Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563 2023 Chevy Z71..daily driver |
04-06-2018, 07:31 PM | #7 |
Post Whore
Join Date: May 2015
Location: Alabama
Posts: 14,657
|
Re: Squares w 2-piece driveshaft
perfectly level is not good...it needs some angle in ds to keep the u-joints lubed...the angle in the joints keeps the needles moving around in the cups...
__________________
Mongo...aka Greg RIP Dad RIP Jesse 1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598 Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334 Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563 2023 Chevy Z71..daily driver |
Bookmarks |
|
|