My fuel tank install

['65 chevy lover]

Here's a few pictures of my fuel tank install Ed. I used an LMC top fill.

[raidmagic]

Oh good. I have questions. I just bought that tank and am hoping to get some shop time today to work on it. Can you show me where you bolted the straps to? Also does the flange bolt to the frame? I have to remove my spare tire brace it appears, did you remove yours? Did you use any kind of rubber between the tank and the frame or straps? How bad will the job be with the bed on? Thanks if you can help, might save me some time out there today.

['65 chevy lover]

Originally Posted by raidmagic

Oh good. I have questions. I just bought that tank and am hoping to get some shop time today to work on it. Can you show me where you bolted the straps to? Also does the flange bolt to the frame? I have to remove my spare tire brace it appears, did you remove yours? Did you use any kind of rubber between the tank and the frame or straps? How bad will the job be with the bed on? Thanks if you can help, might save me some time out there today.

I did remove a brace, not sure what it was. If I remember correctly, It was about an 1-1/4"x1-14". I didn't have to drill holes for anything, just used holes hat were already there for all of it, even the strap. Most of the installs I've seen have used two straps, but if I had done that it would have required me to drill holes for everything. I had to place the tank on the ground and form the strap around it to ensure equal length on each side. I used some of the stuff that was in the box to put on the inside of the strap. I think it's going to be just fine, at least I hope it is...LOL The job would be impossible IMHO with the bed on. Hope this helps you.

[raidmagic]

Originally Posted by '65 chevy lover

I did remove a brace, not sure what it was. If I remember correctly, It was about an 1-1/4"x1-14". I didn't have to drill holes for anything, just used holes hat were already there for all of it, even the strap. Most of the installs I've seen have used two straps, but if I had done that it would have required me to drill holes for everything. I had to place the tank on the ground and form the strap around it to ensure equal length on each side. I used some of the stuff that was in the box to put on the inside of the strap. I think it's going to be just fine, at least I hope it is...LOL The job would be impossible IMHO with the bed on. Hope this helps you.

Ok I've got the tank installed and bolted to the frame. The only thing I don't have done is the strap. For the life of me I'm not understanding where it goes. I have 2 straps and they don't fit anything. Can you show me a picture from underneath how you did your strap? At this point I'm thinking it's a safety measure. I did everything with the bed on btw.

['65 chevy lover]

Originally Posted by raidmagic

Ok I've got the tank installed and bolted to the frame. The only thing I don't have done is the strap. For the life of me I'm not understanding where it goes. I have 2 straps and they don't fit anything. Can you show me a picture from underneath how you did your strap? At this point I'm thinking it's a safety measure. I did everything with the bed on btw.

It'll be tomorrow before I can take some more pictures. You're right, the strap is there for safety. First, straighten out the strap. Then, place the tank on the ground with the bottom facing up. Then, center the strap on the tank. Then, form each end of the strap to wrap around the tank. Then take the bolts with the hook bent on the end and hook into the strap. The bolts are going to be at an angle, but don't worry about that. I used lock nuts so you don't have to worry about them backing off. When you see more pics of all this it will make more sense.
Edit: I just noticed that you said you did all that with the bed on. I thought it would be impossible to do that...lol but apparently not. Anyway, I'll post up some more pictures tomorrow.

[raidmagic]

Originally Posted by '65 chevy lover

It'll be tomorrow before I can take some more pictures. You're right, the strap is there for safety. First, straighten out the strap. Then, place the tank on the ground with the bottom facing up. Then, center the strap on the tank. Then, form each end of the strap to wrap around the tank. Then take the bolts with the hook bent on the end and hook into the strap. The bolts are going to be at an angle, but don't worry about that. I used lock nuts so you don't have to worry about them backing off. When you see more pics of all this it will make more sense.
Edit: I just noticed that you said you did all that with the bed on. I thought it would be impossible to do that...lol but apparently not. Anyway, I'll post up some more pictures tomorrow.

I would have been easier with the bed off but I didn't feel like going through all of that and figured I'd try, we'll see how it goes when I put the strap on

[ImpalaJim]

I have a lmc side fill the cross member is in the way I have a long bedyours looks nice

['65 chevy lover]

Originally Posted by ImpalaJim

I have a lmc side fill the cross member is in the way I have a long bedyours looks nice

Thanks!

[raidmagic]

So you made it that whole way with a single strap. Ok. Thanks.

['65 chevy lover]

Originally Posted by raidmagic

So you made it that whole way with a single strap. Ok. Thanks.

Yep, made it no problem. Just make sure you form it before trying to install it. If you don't, I think it'll be hard to get it to fit right IMHO.

[Captainfab]

You have your strap end hooks upside down. The threaded end goes thru the end of the strap and the nut and washer from the bottom. It installs a whole lot easier that way.

[raidmagic]

Originally Posted by Captainfab

You have your strap end hooks upside down. The threaded end goes thru the end of the strap and the nut and washer from the bottom. It installs a whole lot easier that way.

Well that makes sense. I'll try that when I do mine.

['65 chevy lover]

Originally Posted by Captainfab

You have your strap end hooks upside down. The threaded end goes thru the end of the strap and the nut and washer from the bottom. It installs a whole lot easier that way.

Thanks for the heads up Captain. The bed is not on yet so I can change
It. Also makes it easier to tighten it up if needed.

[WOLFMANmike]

hmmmmm guys i don't know about this . something tells me its a bad idea to use just one strap considering its for safety . true i have not done this yet to my truck but im thinking i would use both straps . just think maybe some how the tank comes lose on the freeway ? slides out of the one strap and hits the ground ? sparks and gas not the best combo and maybe lose your track to a bad fire . when if you had had both straps it would not have happened just my opinion is all just better to be safe than sorry