The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Engine & Drivetrain > Diesel Conversions

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 11-02-2014, 06:42 PM   #1
burnitg
Registered User
 
Join Date: Nov 2009
Location: Black Hawk, CO
Posts: 215
Project Screamer - '72 GMC K2500 + DD 4-53T

I’m starting a project to build my dream truck – a 1972 GMC K2500 with a 4-53T Detroit Diesel.

I learned how to drive in my father’s 1972 GMC. Unfortunately, it is long gone. It succumbed to rust and went to the scrapper.

My ’72 was strictly a sentimental purchase. I have many great memories of my dad’s truck and wanted one of my own. From that standpoint, it is a great truck. Every time I get in, it feels like I’ve stepped into a time machine and I am a kid again.

My dad’s truck was a 2WD. It did fine until things got wet and in Southern Alabama, things got wet frequently. I spent a lot of time getting it unstuck and longed for a 4WD.

I also longed for a truck with a Diesel engine. My father was a partner in an earth moving company that built dikes for fish ponds. He had lots of diesel powered equipment including my favorite, a 12 yd. Euclid scraper with a 6-71 Detroit Diesel. I loved the sound of that “Screaming Jimmy” both at idle and full throttle.

Fast forward 40 years – I have owned 3 pickups, an Isuzu P’up, a Dodge W250 and a Ford F-250, all with Diesel engines.

My fourth is the ’72 GMC. My goal for this conversion is to have a truck that looks as if it came from the factory with the 4-53T installed.

Here's the truck parked in our meadow.

Name:  GMC in the Meadow 9 - small.jpg
Views: 8037
Size:  69.5 KB

Here's the engine. It is out of a 1979 Chevy C-70. The truck was cheap because the engine was making lots of white smoke - poor compression or bad blower (or both!) - so an overhaul is in its future.

Name:  DSC03309 - small.jpg
Views: 5997
Size:  83.4 KB

Here's the transmission. It is a Fuller RT-6610 and is a "take out" too. It will be getting an overhaul and conversion to overdrive.

Name:  DSC03451 - small.jpg
Views: 6246
Size:  74.6 KB

Here's my first attempt at fitting the engine into the frame. DD's are tall so fitting it without a suspension or body lift will be difficult.

Name:  Engine in Frame - small.jpg
Views: 6341
Size:  73.0 KB

Name:  DSC03464 - small.jpg
Views: 5585
Size:  89.2 KB

I will update this post as I make progress. Be patient, I’m not in a hurry…
burnitg is offline   Reply With Quote
Old 11-03-2014, 03:01 PM   #2
shopteacher
Registered User
 
Join Date: Apr 2013
Location: Western Montana
Posts: 50
Re: Project Screamer - '72 GMC K2500 + DD 4-53T

Good deal on the build!
There will be Several of us watching this build to see how it progresses and turns out!
shopteacher is offline   Reply With Quote
Old 11-03-2014, 09:59 PM   #3
Dieselwrencher
6>8 Plugless........
 
Dieselwrencher's Avatar
 
Join Date: Sep 2007
Location: Prairie City, Ia
Posts: 17,112
Re: Project Screamer - '72 GMC K2500 + DD 4-53T

Great project, and it looks like you have a great truck to start with!
__________________
Ryan
1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread
1972 GMC Sierra Grande Longhorn 4x4
1972 Chevy Cheyenne Super K20 Long Step side tilt, tach, tow hooks, AC, 350 4 speed
1972 C10 Suburban Custom Deluxe
1969 Chevy milk truck
1971 Camaro RS 5.3 BTR STG3 Cam Super T10
1940 Ford 354 Hemi 46RH Ford 9" on air ride huge project


Tired of spark plugs? Check this out.
Dieselwrencher is offline   Reply With Quote
Old 11-04-2014, 09:58 AM   #4
burnitg
Registered User
 
Join Date: Nov 2009
Location: Black Hawk, CO
Posts: 215
Re: Project Screamer - '72 GMC K2500 + DD 4-53T

Quote:
Originally Posted by Dieselwrencher View Post
Great project, and it looks like you have a great truck to start with!
Thanks! It is a very nice truck. Aside from a small area on the passenger door, it has no rust. The driver's door is tweaked. It looks like it was hit and then re-skinned. I was able to buy a pair of very nice '72 doors from a board member so I hope there will be very little body work.
burnitg is offline   Reply With Quote
Old 11-06-2014, 11:38 AM   #5
6BT 56
Registered User
 
6BT 56's Avatar
 
Join Date: Dec 2012
Location: Coldwater On. Canada
Posts: 551
Re: Project Screamer - '72 GMC K2500 + DD 4-53T

looks like a cool build for sure . check the 1st page of my build . I had a buddy that has a 56 that has a 53 detroit in it . word has it a garden centre had 10 made on 56 . it has so many factory looking parts on it . its just plain cool . I know its not the rite vintage but it may be good for inspiration.
__________________
56 gmc 4X4 Cummins 5 spd 60F 70R
2005 Ram 3500 DRW cummins 4X4.
2006 Conolift 9/15. 2011 F 350 winter beater
New 2018 ram 3500 drw 4x4. Makes my 2005 Look as if it's been running on 4 cyl since new !
My Build http://67-72chevytrucks.com/vboard/s...d.php?t=556908
6BT 56 is offline   Reply With Quote
Old 11-06-2014, 12:24 PM   #6
burnitg
Registered User
 
Join Date: Nov 2009
Location: Black Hawk, CO
Posts: 215
Re: Project Screamer - '72 GMC K2500 + DD 4-53T

Quote:
Originally Posted by 6BT 56 View Post
looks like a cool build for sure . check the 1st page of my build . I had a buddy that has a 56 that has a 53 detroit in it . word has it a garden centre had 10 made on 56 . it has so many factory looking parts on it . its just plain cool . I know its not the rite vintage but it may be good for inspiration.
Your buddy's '56 looks sweet! If you have any more photos of it, PM them to me.
burnitg is offline   Reply With Quote
Old 11-07-2014, 05:23 PM   #7
burnitg
Registered User
 
Join Date: Nov 2009
Location: Black Hawk, CO
Posts: 215
Re: Project Screamer - '72 GMC K2500 + DD 4-53T

The UPS Man cometh...

I have been on a parts buying binge in the last couple of days. I ordered the motor mounts and while I was waiting for them, I purchased some parts for the engine and transmission that I know I will need.

Here's the clutch. It is the pull type. This is my first experience with a pull type clutch and just learning how to install and set it up has been interesting.

I purchased the clutch kit and received only the pressure plate/release bearing and clutch disk. I still need to find an alignment tool and a clutch brake.

Name:  Pull Clutch - small.jpg
Views: 5670
Size:  67.1 KB

Here's the K-2019 Overdrive conversion kit to make my RT-6610 a RTO-6610. I called a couple of parts vendors and they told me these were no longer being produced and out of stock. If you think you might want one, better buy it now. I purchased this one from General Truck Parts.

Name:  K-2019 Overdrive kit - small.jpg
Views: 5247
Size:  72.4 KB

Here's the K-1850 Basic Rebuild Kit for the RT/RTO-6610. It seems very complete to me...

Name:  K-1850 Rebuild Kit - small.jpg
Views: 5420
Size:  72.5 KB

Here are some parts for the 4-53T. I had to reverse the oil pan to move the sump from the front to the rear so I purchased the longer oil pickup tube for the rear mounted sump. I also purchased a rear main seal, a couple of valve cover gaskets and an oil pan gasket.

Name:  DD Gaskets & Oil Pickup - small.jpg
Views: 5319
Size:  61.0 KB

Here are the motor mounts. I plan to mount the engine from the front mount and the brackets on the flywheel housing. I am looking at a mount for the rear of the transmission. There is no obvious place on the transmission for attachment so I will have to get creative.

Name:  Motor Mounts - small.jpg
Views: 5199
Size:  69.9 KB

Next step - fabricate motor mount plates for the front and rear of the engine and weld them into the chassis.
burnitg is offline   Reply With Quote
Old 11-08-2014, 01:58 AM   #8
Dieselwrencher
6>8 Plugless........
 
Dieselwrencher's Avatar
 
Join Date: Sep 2007
Location: Prairie City, Ia
Posts: 17,112
Re: Project Screamer - '72 GMC K2500 + DD 4-53T

Nice parts pile! That's to bad they offed those RTO's!
__________________
Ryan
1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread
1972 GMC Sierra Grande Longhorn 4x4
1972 Chevy Cheyenne Super K20 Long Step side tilt, tach, tow hooks, AC, 350 4 speed
1972 C10 Suburban Custom Deluxe
1969 Chevy milk truck
1971 Camaro RS 5.3 BTR STG3 Cam Super T10
1940 Ford 354 Hemi 46RH Ford 9" on air ride huge project


Tired of spark plugs? Check this out.
Dieselwrencher is offline   Reply With Quote
Old 11-08-2014, 12:30 PM   #9
mx289
Registered User
 
mx289's Avatar
 
Join Date: May 2013
Location: wall,nj
Posts: 865
Re: Project Screamer - '72 GMC K2500 + DD 4-53T

Very cool build and looks like a great truck to start with.

Awesome motor/trans.

Excited to watch this one.
__________________
Tom

71 K2500
71 K5 Jimmy
mx289 is offline   Reply With Quote
Old 11-09-2014, 04:53 PM   #10
ryanroo
Senior Member
 
ryanroo's Avatar
 
Join Date: Apr 2004
Location: sw colorado
Posts: 2,720
Re: Project Screamer - '72 GMC K2500 + DD 4-53T

in to watch!
__________________
72 K20 12v build
72 K20 "parts truck"

ryanroo is offline   Reply With Quote
Old 11-10-2014, 11:19 PM   #11
6BT 56
Registered User
 
6BT 56's Avatar
 
Join Date: Dec 2012
Location: Coldwater On. Canada
Posts: 551
Re: Project Screamer - '72 GMC K2500 + DD 4-53T

Quote:
Originally Posted by burnitg View Post
Your buddy's '56 looks sweet! If you have any more photos of it, PM them to me.
Those were the only pics i had . Was going to be cool for sure . It had the driptroit . A 4 spd and a brownie box behind that . He bought all my 1 ton napco stuff that was in my truck and was going to add all it to his truck.
__________________
56 gmc 4X4 Cummins 5 spd 60F 70R
2005 Ram 3500 DRW cummins 4X4.
2006 Conolift 9/15. 2011 F 350 winter beater
New 2018 ram 3500 drw 4x4. Makes my 2005 Look as if it's been running on 4 cyl since new !
My Build http://67-72chevytrucks.com/vboard/s...d.php?t=556908
6BT 56 is offline   Reply With Quote
Old 11-12-2014, 12:28 PM   #12
Lemield
Registered User
 
Lemield's Avatar
 
Join Date: Dec 2004
Location: Arvada Colorado
Posts: 1,321
Re: Project Screamer - '72 GMC K2500 + DD 4-53T

Cool project Burnitg! I'm subscribing so I can follow along.

I have a 1971 K20 with a 6.2 turbo diesel conversion so I understand your desire for a diesel. I also recently put a Kubota V2203 turbo diesel in my 1949 Willys Jeep. Love those diesels!

Good luck on your project!
__________________
Larry

1949 Willys CJ2A, Kubota Turbo Diesel engine, Warn Overdrive, 11 inch brakes, 12volt, Warn M8000 Winch "Little Green"
1970 Rustoleum Roller Red C20 Custom Camper 454 TH400 "Big Red"
1971 K20 6.2 Turbo Diesel 4x4 4spd Ranger Overdrive "Pumpkin Wagon"
2005 VW Beetle Diesel 44+ MPG "Silver Bullet"
Lemield is offline   Reply With Quote
Old 11-13-2014, 03:58 AM   #13
muffintop
Registered User
 
Join Date: Nov 2013
Location: sedro woolley, washington
Posts: 71
Re: Project Screamer - '72 GMC K2500 + DD 4-53T

best part is if you got it to run on corn oil ;]
muffintop is offline   Reply With Quote
Old 11-14-2014, 12:24 PM   #14
burnin oil
Registered User
 
Join Date: Jan 2013
Location: Eastern TN
Posts: 1,919
Re: Project Screamer - '72 GMC K2500 + DD 4-53T

The clutch brake and alignment tool can be bought at any big truck place such as fleet pride. Those parts are cheap and you can probably get them both for under $30. I have a 6613 with an OD conversion to put into a truck one day. I need to make an adapter for a transfercase first.
burnin oil is offline   Reply With Quote
Old 11-14-2014, 02:29 PM   #15
burnitg
Registered User
 
Join Date: Nov 2009
Location: Black Hawk, CO
Posts: 215
Re: Project Screamer - '72 GMC K2500 + DD 4-53T

I have made some progress on the engine mounts. The front mount is complete and welded in from the top. I will flip the frame and weld the bottom later.

Here's a couple of views of the mount:

Name:  Front Engine Mount 1 - small.jpg
Views: 5971
Size:  84.0 KB

Name:  Front Engine Mount side - small.jpg
Views: 6672
Size:  80.1 KB

Name:  Front Engine Mount with Engine - small.jpg
Views: 5410
Size:  71.1 KB

I'm ready to start on the rear mounts. I have decided to replace the rear spring hangers of the front springs and box the frame in that area. The torque of the engine will be transferred by these mounts and I feel that the frame should be stronger.

Here's a mock up of the engine connected to the front mounts and in its correct position:

Name:  Engine mock up after front engine mount - small.jpg
Views: 6919
Size:  88.7 KB

I'll have to go to town and hunt up the correct tubing for the rear spring hanger.

On the parts front, I have the clutch brake and alignment tool. I am still looking for a horizontal, spin on oil filter since the current filter will hit the front differential and the correct fan hub and pulley.

More to come...
burnitg is offline   Reply With Quote
Old 11-14-2014, 08:00 PM   #16
ryanroo
Senior Member
 
ryanroo's Avatar
 
Join Date: Apr 2004
Location: sw colorado
Posts: 2,720
Re: Project Screamer - '72 GMC K2500 + DD 4-53T

looking good! are you planning on using a beefier bushing for the shackle hanger? i would recommend it if you weren't already.
__________________
72 K20 12v build
72 K20 "parts truck"

ryanroo is offline   Reply With Quote
Old 11-15-2014, 01:02 PM   #17
burnitg
Registered User
 
Join Date: Nov 2009
Location: Black Hawk, CO
Posts: 215
Re: Project Screamer - '72 GMC K2500 + DD 4-53T

Quote:
Originally Posted by ryanroo View Post
looking good! are you planning on using a beefier bushing for the shackle hanger? i would recommend it if you weren't already.

Thanks for the advice, Ryan. I have been following your build with interest. I am envious of your access to tools and equipment.

I was hoping to find some 1.5" 0.250 wall DOM tubing when I go down to Denver next week. If I can't find any, I will probably have someone turn me a pair of bushings.
burnitg is offline   Reply With Quote
Old 11-15-2014, 03:05 PM   #18
Vintage Windmills
Vintage 4x4s
 
Vintage Windmills's Avatar
 
Join Date: Sep 2010
Location: Prior Lake, MN
Posts: 4,305
Re: Project Screamer - '72 GMC K2500 + DD 4-53T

Cool project, I like how you are going with a factory look. I will definitely be following this!
__________________

67 GMC K1500 Custom- 305V6 SM420, PTO, Ram Assist, yellow (the outcast) (project period correct upgrades)
67 GMC C2500 351V6 TH400, AC, PS, PB (can't decide what to do with. Update, decided to keep and will restore )
86 CHV K30 502 th400, apple red NEW
71 CHV K20 350 SM465, ochre (saved work truck)
71 CHV K20 292 SM465, white, tach, PTO, (future project)
72 CHV K20 350 350th, medium blue (project stocker)
01 CHV K2500hd crew, indigo blue

^3 dont run and the others don't see winter either
'86 K30 Cummins "Fireside" thread: http://67-72chevytrucks.com/vboard/s...d.php?t=649649
'71 K20 "get driveable" thread: http://67-72chevytrucks.com/vboard/s...d.php?t=590642
'72 K20 Build Thread: http://67-72chevytrucks.com/vboard/s...=493477&page=6
Vintage Windmills is offline   Reply With Quote
Old 12-15-2014, 02:47 PM   #19
burnitg
Registered User
 
Join Date: Nov 2009
Location: Black Hawk, CO
Posts: 215
Re: Project Screamer - '72 GMC K2500 + DD 4-53T

A little progress and a lot of family time...

I hope that you had a wonderful Thanksgiving. I sure did. I spent a lot of time with my family and friends. This is my favorite time of year.

I also made a little progress on my project.

I received my divorced NP-205 transfer case:

Name:  Divorced NP205 (small).jpg
Views: 6084
Size:  81.3 KB

I purchased some 1-3/4" DOM tubing and had a local machine shop cut it to the correct length and bore the ID:

Name:  Front Spring Bushings (small).jpg
Views: 4983
Size:  24.0 KB

I mocked up the rear motor mounts:

Name:  Rear Motor Mount Mock-up (small).jpg
Views: 5509
Size:  87.0 KB

And burned them in:

Name:  Rear Motor Mount Burned In - 1 (small).jpg
Views: 5224
Size:  59.1 KB

Name:  Rear Motor Mount Burned In - 2 (small).jpg
Views: 7120
Size:  78.5 KB

I flipped the chassis and welded the bottom side of the front and rear motor mounts. Before I could flip the chassis, I had to remove the axles. This took a lot longer than I had expected because the bolts had rusted solid to the sleeves inside the bushings. When I reassemble them, I will be liberally coating the entire bolt and sleeve with anti-seize lubricant!

Next step - cut and install the boxing plates and install the spring bushings so I can make the chassis a roller again.

More to come...
burnitg is offline   Reply With Quote
Old 12-16-2014, 11:27 AM   #20
Vintage Windmills
Vintage 4x4s
 
Vintage Windmills's Avatar
 
Join Date: Sep 2010
Location: Prior Lake, MN
Posts: 4,305
Re: Project Screamer - '72 GMC K2500 + DD 4-53T

Looks good, good progress. Those polyurethane motor mounts look nice and will last a long time but unfortunately will transfer more vibration to the chassis than rubber.
__________________

67 GMC K1500 Custom- 305V6 SM420, PTO, Ram Assist, yellow (the outcast) (project period correct upgrades)
67 GMC C2500 351V6 TH400, AC, PS, PB (can't decide what to do with. Update, decided to keep and will restore )
86 CHV K30 502 th400, apple red NEW
71 CHV K20 350 SM465, ochre (saved work truck)
71 CHV K20 292 SM465, white, tach, PTO, (future project)
72 CHV K20 350 350th, medium blue (project stocker)
01 CHV K2500hd crew, indigo blue

^3 dont run and the others don't see winter either
'86 K30 Cummins "Fireside" thread: http://67-72chevytrucks.com/vboard/s...d.php?t=649649
'71 K20 "get driveable" thread: http://67-72chevytrucks.com/vboard/s...d.php?t=590642
'72 K20 Build Thread: http://67-72chevytrucks.com/vboard/s...=493477&page=6
Vintage Windmills is offline   Reply With Quote
Old 12-16-2014, 12:21 PM   #21
burnitg
Registered User
 
Join Date: Nov 2009
Location: Black Hawk, CO
Posts: 215
Re: Project Screamer - '72 GMC K2500 + DD 4-53T

Quote:
Originally Posted by Vintage Windmills View Post
Looks good, good progress. Those polyurethane motor mounts look nice and will last a long time but unfortunately will transfer more vibration to the chassis than rubber.
Yes, I recognize that the poly mounts will transfer more vibration than rubber. I purchased the more flexible (greater isolation) mounts hoping that they would be a good compromise. I'll know the first time I fire it up...
burnitg is offline   Reply With Quote
Old 12-16-2014, 06:06 PM   #22
Dieselwrencher
6>8 Plugless........
 
Dieselwrencher's Avatar
 
Join Date: Sep 2007
Location: Prairie City, Ia
Posts: 17,112
Re: Project Screamer - '72 GMC K2500 + DD 4-53T

If it doesn't shake a little, it isn't an old truck. Nice work sir! It looks like you may have some firewall and floor reconstruction in your future too! Keep up the great work!
__________________
Ryan
1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread
1972 GMC Sierra Grande Longhorn 4x4
1972 Chevy Cheyenne Super K20 Long Step side tilt, tach, tow hooks, AC, 350 4 speed
1972 C10 Suburban Custom Deluxe
1969 Chevy milk truck
1971 Camaro RS 5.3 BTR STG3 Cam Super T10
1940 Ford 354 Hemi 46RH Ford 9" on air ride huge project


Tired of spark plugs? Check this out.
Dieselwrencher is offline   Reply With Quote
Old 12-17-2014, 11:00 AM   #23
brimc
Registered User
 
brimc's Avatar
 
Join Date: Jun 2013
Location: New Lowell, Ontario, Canada
Posts: 248
Re: Project Screamer - '72 GMC K2500 + DD 4-53T

Quote:
Originally Posted by burnitg View Post

I received my divorced NP-205 transfer case:

Attachment 1336878
Really interested how you make this work. Awesome build for sure. How did you get the 205 and what are your plans to make it work?
__________________
BRIAN

1986 Chevrolet K20 Silverado 12 Valve CUMMINS P Pumped Intercooled/Getrag360/Divorced NP205/10B/14BFF Detroit Locker - DD Canadian Winter Beater.

My Chevrolet CUMMINS Build http://67-72chevytrucks.com/vboard/s...d.php?t=585509
brimc is offline   Reply With Quote
Old 12-17-2014, 11:58 AM   #24
burnitg
Registered User
 
Join Date: Nov 2009
Location: Black Hawk, CO
Posts: 215
Re: Project Screamer - '72 GMC K2500 + DD 4-53T

Quote:
Originally Posted by Dieselwrencher View Post
If it doesn't shake a little, it isn't an old truck. Nice work sir! It looks like you may have some firewall and floor reconstruction in your future too! Keep up the great work!
It will shake some; although, in my experience Detroits are pretty smooth just very loud. I used Lizard Skin sound deadening on one of my other trucks and it made a world of difference. I am planning to use it on this one too.

I'm planning to get the driveline and exhaust squared away before I tackle the firewall and floor mods. The 4-53 is both taller and longer than the 350 it replaced so I know that I will have some cab modifications to make.
burnitg is offline   Reply With Quote
Old 12-17-2014, 12:10 PM   #25
burnitg
Registered User
 
Join Date: Nov 2009
Location: Black Hawk, CO
Posts: 215
Re: Project Screamer - '72 GMC K2500 + DD 4-53T

Quote:
Originally Posted by brimc View Post
Really interested how you make this work. Awesome build for sure. How did you get the 205 and what are your plans to make it work?
I purchased the NP-205 on eBay. Just search for "divorced NP-205" and you should find several for sale.

I will end up with 3 custom drive shafts. The one that connects the transmission to the transfer case will be as short as possible and odd because the output yoke of the RT6610 is huge (1710) and the input of the transfer case is normal size.

Once I get the transmission to T-case shaft, I will fab a custom crossmember to support the T-case. Then I will have the other two shafts made. The front shaft will be the long one in this case. It may be long enough to need a center bearing.

Stay tuned and you will see it come together.
burnitg is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 04:02 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com