TX 1972 lwb Ac cab truck parting it out

[Mapearso]

I need the upper molding end cap pieces
Thanks

[zicc1835]

Originally Posted by HSRACER

45 plus shipping. It even has the door light actuators that are spring loaded.

Ill take complete with fuse block and all can you get it out and take pic send me your pay info and my zip is 07981thanks
Jess
NO HURRY ON MY END

[REEDS 72]

Originally Posted by HSRACER

It looks pretty good. Didn't really see much for cuts or splices. 20 dollars plus shipping. I haven't removed all of it yet but can look at it tomorrow

Can you do a close up pic when you get it out no hurry thank you.

[ScottieB]

Is the whole vent system intact with hoses and plastic that's undamaged? and linkages, etc?

most of mine is trashed.

Also looking for a gas pedal, mine is a 'nub'
Stock coolant and wiper fluid tanks (and hopefully wiper pump)

If so, how much is shipping to 76528 (tx) - I'm in gatesville ... west of waco. I'm not driving to houston lol

[HSRACER]

Originally Posted by ScottieB

Is the whole vent system intact with hoses and plastic that's undamaged? and linkages, etc?

most of mine is trashed.

Also looking for a gas pedal, mine is a 'nub'
Stock coolant and wiper fluid tanks (and hopefully wiper pump)

If so, how much is shipping to 76528 (tx) - I'm in gatesville ... west of waco. I'm not driving to houston lol

I have the vacuum canister and the fender bracket. No fluid tanks.

[ScottieB]

i think i'm getting the tanks from another guy... and a pedal.

Do you have the whole intact inside vent system? (don't need the vents themselves. ducts / etc is what i need)

[HSRACER]

Originally Posted by ScottieB

i think i'm getting the tanks from another guy... and a pedal.

Do you have the whole intact inside vent system?

I am not sure what all that consists of. I have the vaccumn actuated flapper for the passenger side vent and the one for the flapper in the cowl area.

[ScottieB]

http://www.lmctruck.com/icatalog/cb/full.aspx?Page=65

I need this stuff

[speedracer]

are you planning on removing the bed? I need a pair of the flatish bed mounts if they are in good shape. thanks

[HSRACER]

Originally Posted by speedracer

are you planning on removing the bed? I need a pair of the flatish bed mounts if they are in good shape. thanks

Not sure yet but I hope to sell the bed or the complete frame and bed together.

[HSRACER]

Originally Posted by ScottieB

http://www.lmctruck.com/icatalog/cb/full.aspx?Page=65

I need this stuff

I have almost all the parts that go with the Ac and heat ducting. I threw away all the flexible vent hoses as they were disintegrating. The Ac vents in the dash were missing.

[1968aj]

I will take the seat belts

[zicc1835]

Originally Posted by zicc1835

Ill take complete with fuse block and all can you get it out and take pic send me your pay info and my zip is 07981 thanks
Jess
NO HURRY ON MY END

??just looking for a reply on this

[HSRACER]

Here is what I have. 60'dollars with the defrost vents included and add the shipping to that. Let me know. Thanks

[HSRACER]

Originally Posted by zicc1835

??just looking for a reply on this

Sorry I worked all day stripping the truck today. I did get a picture of this harness. I will be on the road for the week but can try and figure out the shipping before I leave tomorrow.

[HSRACER]

Another shot.

[HSRACER]

Originally Posted by REEDS 72

Can you do a close up pic when you get it out no hurry thank you.

So here is a picture. There are two harnesses to the back, one is the long 4 wire and the other is the harness for all the rear lights. Which one did you need?

[HSRACER]

The ends look good and no breaks in the wire on the long run from the cab to the back.

[zicc1835]

Originally Posted by HSRACER

Another shot.

Al,
thank you that is exactly what i need should fit in one of the USPS late rate boxes ill p m you my address LMK how you want to get paid I too travel ...this week 2 days only next week for the week and so it goes so no hurry on my end
thanks Again
Jess

[HSRACER]

Originally Posted by ironfish96

I'm interested in the automatic steering column and the steering box. What are you asking for it? I'm in Beaumont so I could pick. Thanks Vance

Did you want these? I asked 100 for both.

[HSRACER]

Originally Posted by HSRACER

25 plus shipping

Did you want this?

[zicc1835]

if reeds wants that one ill get in line for the Taillight harness that feeds the tails backups and lic. plate pending condition
JZ

[HSRACER]

Tail lights harness is pretty good. I would re wrap them as the cover is brittle and falling off. The wires are good. Someone cut the wires going to the passenger light but it is just butt connected.

[HSRACER]

Here is a picture of the taillight harness.

[HSRACER]

Here is some pretty cool tail lights for a patina project. The stainless could be cleaned up if you wanted. But the lenses have spider cracks.