Roll bar color - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**Gary 70 Jimmy** · 06-03-2005, 12:25 AM

Is this plate welded on I will email the guy I got the roll bar off of and ask him if their is a plate under the bed.

Having trouble getting the roll bar level it looks like it needs to go further forward but the carpet hold strip is in the way do you have to remove it to get it level

71jimmy · 06-03-2005, 01:35 AM

VT I think he's talking about backing plates for the rollbar. I don't have them either yet, need to make some, should be pretty easy.

Gary, so you have the short seatbelt retractor for the passenger side and there is no hole to mount it on the vertical, just like in the picture? And like VT said, should have a captive nut to bolt it to.

*Medicanman71* · 06-03-2005, 08:38 AM

I made mine in autobody... WAy back in HS

the other guy in town doesnt have any, he just welded his in - and its not a junker neither so i dont get it!??!?

I have a question for you guys (That i know the answer to - i found out haha)

IS IT POSSIBLE TO SEAT A ROLL BAR PROPERLY IN A BLAZER WITH OUT TAKING THE TOP OFF!!?!?!?!?!

This is a good one...

**Gary 70 Jimmy** · 06-03-2005, 08:51 AM

71 jimmy no hole I will have to drill one and put a nut on the back

The blazer my roll bar came out of still had the top on it

*Medicanman71* · 06-05-2005, 04:04 AM

Oh, so i guess you already found out too, heh.

No welding is needed for the roll bar if you use the plate things underneath the wheel wells instead of just washers..

06-03-2005, 12:25 AM	#26
Gary 70 Jimmy Senior Member Join Date: Jan 2002 Location: Burghill, Ohio 44404 Posts: 3,401	Is this plate welded on I will email the guy I got the roll bar off of and ask him if their is a plate under the bed. Having trouble getting the roll bar level it looks like it needs to go further forward but the carpet hold strip is in the way do you have to remove it to get it level Last edited by Gary 70 Jimmy; 06-03-2005 at 08:53 AM.

06-03-2005, 01:35 AM	#27
71jimmy Registered User Join Date: Mar 2004 Location: Sacramento, CA Posts: 1,084	VT I think he's talking about backing plates for the rollbar. I don't have them either yet, need to make some, should be pretty easy. Gary, so you have the short seatbelt retractor for the passenger side and there is no hole to mount it on the vertical, just like in the picture? And like VT said, should have a captive nut to bolt it to. __________________ '71 Jimmy, 350, SM465, NP205, 2in Tuff Country lift, 33s on rallies, TBI, softtop and hardtop "If life was fair you'd be able to afford one of each and a garage large enough to house them all."

06-03-2005, 08:51 AM	#29
Gary 70 Jimmy Senior Member Join Date: Jan 2002 Location: Burghill, Ohio 44404 Posts: 3,401	71 jimmy no hole I will have to drill one and put a nut on the back The blazer my roll bar came out of still had the top on it Last edited by Gary 70 Jimmy; 06-03-2005 at 08:56 AM.

06-03-2005, 08:38 AM	#28
Medicanman71 Account Suspended Join Date: May 2005 Location: Where the Wild Things Are Posts: 696	I made mine in autobody... WAy back in HS the other guy in town doesnt have any, he just welded his in - and its not a junker neither so i dont get it!??!? I have a question for you guys (That i know the answer to - i found out haha) IS IT POSSIBLE TO SEAT A ROLL BAR PROPERLY IN A BLAZER WITH OUT TAKING THE TOP OFF!!?!?!?!?! This is a good one...

06-05-2005, 04:04 AM	#30
Medicanman71 Account Suspended Join Date: May 2005 Location: Where the Wild Things Are Posts: 696	Oh, so i guess you already found out too, heh. No welding is needed for the roll bar if you use the plate things underneath the wheel wells instead of just washers..



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.