1972 Stepside SWB - Page 4 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

whiteyandreddy · 05-13-2012, 03:05 AM

The filler neck in its new location will allow the fuel door to be hidden in the bed.

whiteyandreddy · 05-13-2012, 03:14 AM

Other progress made today was to complete the rear electrical. The side marker lamps, tail lights and license plate lights were routed and wired up. All of the lights are now working on the truck. I also installed the license plate bracket and ran stainless steel over braid (aka "Expando") over the tail light wiring. I used a NAPA insulated clamp to hold wiring against the bedside. The tailights are not original obvioulsly. I bought them at a swap meet, and believe they are from a '37 to '42 Ford wagon or truck.

mcbassin · 05-13-2012, 10:05 AM

Very nice work on the filler relocation. Good progress.

Tinkermc · 05-13-2012, 11:52 AM

very nice

baldwinc · 05-23-2012, 12:55 AM

Me likey!

whiteyandreddy · 05-23-2012, 01:07 AM

A little more progress and a roadblock. I have several leaks on the HDPE plastic gas tank, the most severe of which is at the fuel sending unit. I have some more work to do! I will try to repair the leaks at the welds and let you know how they turn out. The sending unit may be harder. I can't see if it is leaking at the seal or at the screw holes which hold the cleats down. Progress was made on the interior. I was persuaded to move away from the original AM radio to a more modern one. It's very nice and was very easy to install. Speakers will be mounted once I have the seat in, which hopefully will be soon. I also removed and repainted the left inner fender and a bunch of bolts that needed some touch up. I also had a chance to finish the washer pump hose installation and repainted the washer nozzles. I will be reinstalling the cowl this weekend along trying to pin down and fix the leaks.

67c10rustbuket · 05-23-2012, 09:47 AM

Looking good! Nice fuel tank mod too, The tailight wire covering/mounting is slick as well. You have a lot of nice detail in this truck, keep it up!

Tinkermc · 06-03-2012, 07:26 PM

it really does look nice

whiteyandreddy · 06-08-2012, 02:06 AM

Updated progress over the past two weeks:
I am still having trouble with the plastic tank sealing at the sending unit. The welds are holding water fine. I have replaced the o-ring, adjusted the fuel strainer up so its not hitting the bottom of the tank, teflon-taped the screws for the hold-down clamps, and reduced the diameter of the retainer ring all to have it tight when the hold-down clamps are tightened. I still have a leak at what I believe is the o-ring. I set a deadline of June 17th to have the truck on the road, so I switched paths to an aluminum tank from ProPerformance in AZ, who represents Boyd welding of Florida. I received the tank today (8 business days after ordering-amazing) and mounted it tonight. Travis at ProPerformance was simply excellent to work with and the tank is impressive. It fits perfectly in the frame. I will be filling the tank this weekend after priming the engine oil and fuel lines. Many thanks to my friend, Joe, who stopped by to help tonight.
Other tasks completed recently:
Finished the kick panel install using the vent door lever mounting screw holes, installed the dash pad, glove box & steering wheel I also finished interior wiring, windshield wipers, and re-mounted the front bumper. I also got the bench seat recovered in black vinyl. Here are some pictures. I will try to post agin this weekend after working on the truck again.

whiteyandreddy · 06-08-2012, 02:14 AM

Some more pictures of other recent progress. When I purchased the truck, I didn't realize the seat was not original. I believe it is an early '80's Chevy truck based on a truck I used parts from.

whiteyandreddy · 06-08-2012, 02:19 AM

And one of the interior. The kicker panels from Custom Auot Sound only needed minor modification. I used an ultrasonic tool to cut the plastic and used #10 black trim screws to mount them along with the door vent levers. The emergency brake is really close to interfering with the face of the driver's speaker.

**67cheby** · 06-08-2012, 01:19 PM

looking good !

Pro Performance · 06-11-2012, 10:55 PM

Truck looks great, and you're right, that filler neck is in perfect location. You will have to post some pictures when you get the "door" finished. Thanks for the good words.
Posted via Mobile Device

whiteyandreddy · 06-13-2012, 01:56 AM

My brother stopped by Saturday to help on the truck, and then a couple of other friends (Thanks Don, Rob and Leon!), so we really got a lot done this weekend and early this week. We managed to finish the bed wood modification, bolt replacement, the interior door panels and handles, fixed some small wiring problems, and clamped down the fuel lines to the chassis. We also primed the oil pump, finished the fuel line attachment, filled the gas tank and got the truck running! It ran well considering the last time I had run it was September 2011. We are very close to having it ready for the Father's Day weekend drive!
Here are some images.

whiteyandreddy · 06-13-2012, 02:07 AM

Here are a couple more pictures of the nearly finished truck. There are a few more things to finish up, particularly in the engine bay, and detailing. I will be working to carpet installed next week. I want to make sure all of the wiring is OK before we cover it up with carpet. I am starting to see why people say the projects are never truly done.

VA72C10 · 06-13-2012, 02:10 AM

Truck looks GREAT! Nice job!!!

**67cheby** · 06-13-2012, 06:08 AM

Very nice !
Posted via Mobile Device

67c10rustbuket · 06-13-2012, 10:10 AM

Congrats ! that is awesome

I have one of those Boyd tanks also, they are VERY nice!

mcbassin · 06-13-2012, 10:35 AM

Your truck looks great! Love it!
Posted via Mobile Device

whiteyandreddy · 07-13-2012, 12:46 AM

Thanks for the kinds words. Sorry I haven't posted for a while. I have been working a lot, had computer problems and the truck was getting the carpet installed. I will post some new photos this weekend after some detailing.

whiteyandreddy · 07-17-2012, 11:11 PM

Here are some photos of the truck after a lot of detailing, taken on Saturday, at a local car show.

Pro Performance · 07-17-2012, 11:19 PM

Truck looks great!

insane04 · 07-17-2012, 11:42 PM

dam i love it!!

67c10rustbuket · 07-18-2012, 07:17 AM

PERFECT!! Excellent job man, must be great to be able to cruise it to a show!

Kregb · 07-18-2012, 02:34 PM

Great to see the truck in person and talk to you. The pictures don't do the truck justice it looks much better in person. Thanks for letting me know you would have it at the show. I will make it a point to see any time I know you have it out, inspires me to work a little harder on mine.

05-13-2012, 03:05 AM	#76
whiteyandreddy Registered User Join Date: Jan 2010 Location: Erie, CO Posts: 83	Re: 1972 Stepside SWB The filler neck in its new location will allow the fuel door to be hidden in the bed. Attached Images __________________ Check out my project: 1972 Chevrolet Stepside- Shortbed http://67-72chevytrucks.com/vboard/s...d.php?t=392386 . . . . . . . . . . .__ . . . . . ______l__l\___ . . . . .l_[(O)]_____(O)]

05-13-2012, 03:14 AM	#77
whiteyandreddy Registered User Join Date: Jan 2010 Location: Erie, CO Posts: 83	Re: 1972 Stepside SWB Other progress made today was to complete the rear electrical. The side marker lamps, tail lights and license plate lights were routed and wired up. All of the lights are now working on the truck. I also installed the license plate bracket and ran stainless steel over braid (aka "Expando") over the tail light wiring. I used a NAPA insulated clamp to hold wiring against the bedside. The tailights are not original obvioulsly. I bought them at a swap meet, and believe they are from a '37 to '42 Ford wagon or truck. Attached Images __________________ Check out my project: 1972 Chevrolet Stepside- Shortbed http://67-72chevytrucks.com/vboard/s...d.php?t=392386 . . . . . . . . . . .__ . . . . . ______l__l\___ . . . . .l_[(O)]_____(O)]

05-13-2012, 10:05 AM	#78
mcbassin Still Learning Join Date: Jul 2009 Location: Central Oklahoma Posts: 10,108	Re: 1972 Stepside SWB Very nice work on the filler relocation. Good progress. __________________ Mike "69 Short Wide" My Project 86 Silverado Landen's Project Instagram: @mcbassin My Website C/10 Club Oklahoma Facebook Group

05-13-2012, 11:52 AM	#79
Tinkermc Registered User Join Date: Jul 2011 Location: Farmville, Va Posts: 3,026	Re: 1972 Stepside SWB very nice

05-23-2012, 12:55 AM	#80
baldwinc Registered User Join Date: Aug 2011 Location: NN VA Posts: 1	Re: 1972 Stepside SWB Me likey!

05-23-2012, 01:07 AM	#81
whiteyandreddy Registered User Join Date: Jan 2010 Location: Erie, CO Posts: 83	Re: 1972 Stepside SWB A little more progress and a roadblock. I have several leaks on the HDPE plastic gas tank, the most severe of which is at the fuel sending unit. I have some more work to do! I will try to repair the leaks at the welds and let you know how they turn out. The sending unit may be harder. I can't see if it is leaking at the seal or at the screw holes which hold the cleats down. Progress was made on the interior. I was persuaded to move away from the original AM radio to a more modern one. It's very nice and was very easy to install. Speakers will be mounted once I have the seat in, which hopefully will be soon. I also removed and repainted the left inner fender and a bunch of bolts that needed some touch up. I also had a chance to finish the washer pump hose installation and repainted the washer nozzles. I will be reinstalling the cowl this weekend along trying to pin down and fix the leaks. Attached Images __________________ Check out my project: 1972 Chevrolet Stepside- Shortbed http://67-72chevytrucks.com/vboard/s...d.php?t=392386 . . . . . . . . . . .__ . . . . . ______l__l\___ . . . . .l_[(O)]_____(O)]

05-23-2012, 09:47 AM	#82
67c10rustbuket Registered User Join Date: Apr 2011 Location: Mustang, Oklahoma Posts: 2,806	Re: 1972 Stepside SWB Looking good! Nice fuel tank mod too, The tailight wire covering/mounting is slick as well. You have a lot of nice detail in this truck, keep it up! __________________ Dan <---(my name) 67 SWB C10 project "GEORGIA"-59 Brookwood 2dr wag...Next project-03 Tahoe 4x4 5.3 family ride-07 Hondur Accord, commuter car

06-03-2012, 07:26 PM	#83
Tinkermc Registered User Join Date: Jul 2011 Location: Farmville, Va Posts: 3,026	Re: 1972 Stepside SWB it really does look nice

06-08-2012, 02:06 AM	#84
whiteyandreddy Registered User Join Date: Jan 2010 Location: Erie, CO Posts: 83	Re: 1972 Stepside SWB Updated progress over the past two weeks: I am still having trouble with the plastic tank sealing at the sending unit. The welds are holding water fine. I have replaced the o-ring, adjusted the fuel strainer up so its not hitting the bottom of the tank, teflon-taped the screws for the hold-down clamps, and reduced the diameter of the retainer ring all to have it tight when the hold-down clamps are tightened. I still have a leak at what I believe is the o-ring. I set a deadline of June 17th to have the truck on the road, so I switched paths to an aluminum tank from ProPerformance in AZ, who represents Boyd welding of Florida. I received the tank today (8 business days after ordering-amazing) and mounted it tonight. Travis at ProPerformance was simply excellent to work with and the tank is impressive. It fits perfectly in the frame. I will be filling the tank this weekend after priming the engine oil and fuel lines. Many thanks to my friend, Joe, who stopped by to help tonight. Other tasks completed recently: Finished the kick panel install using the vent door lever mounting screw holes, installed the dash pad, glove box & steering wheel I also finished interior wiring, windshield wipers, and re-mounted the front bumper. I also got the bench seat recovered in black vinyl. Here are some pictures. I will try to post agin this weekend after working on the truck again. Attached Images __________________ Check out my project: 1972 Chevrolet Stepside- Shortbed http://67-72chevytrucks.com/vboard/s...d.php?t=392386 . . . . . . . . . . .__ . . . . . ______l__l\___ . . . . .l_[(O)]_____(O)]

06-08-2012, 02:14 AM	#85
whiteyandreddy Registered User Join Date: Jan 2010 Location: Erie, CO Posts: 83	Re: 1972 Stepside SWB Some more pictures of other recent progress. When I purchased the truck, I didn't realize the seat was not original. I believe it is an early '80's Chevy truck based on a truck I used parts from. Attached Images __________________ Check out my project: 1972 Chevrolet Stepside- Shortbed http://67-72chevytrucks.com/vboard/s...d.php?t=392386 . . . . . . . . . . .__ . . . . . ______l__l\___ . . . . .l_[(O)]_____(O)]

06-08-2012, 02:19 AM	#86
whiteyandreddy Registered User Join Date: Jan 2010 Location: Erie, CO Posts: 83	Re: 1972 Stepside SWB And one of the interior. The kicker panels from Custom Auot Sound only needed minor modification. I used an ultrasonic tool to cut the plastic and used #10 black trim screws to mount them along with the door vent levers. The emergency brake is really close to interfering with the face of the driver's speaker. Attached Images __________________ Check out my project: 1972 Chevrolet Stepside- Shortbed http://67-72chevytrucks.com/vboard/s...d.php?t=392386 . . . . . . . . . . .__ . . . . . ______l__l\___ . . . . .l_[(O)]_____(O)]

06-08-2012, 01:19 PM	#87
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: 1972 Stepside SWB looking good ! __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

06-11-2012, 10:55 PM	#88
Pro Performance Registered User Join Date: Aug 2010 Location: AZ Posts: 3,069	Re: 1972 Stepside SWB Truck looks great, and you're right, that filler neck is in perfect location. You will have to post some pictures when you get the "door" finished. Thanks for the good words. Posted via Mobile Device

06-13-2012, 01:56 AM	#89
whiteyandreddy Registered User Join Date: Jan 2010 Location: Erie, CO Posts: 83	Re: 1972 Stepside SWB My brother stopped by Saturday to help on the truck, and then a couple of other friends (Thanks Don, Rob and Leon!), so we really got a lot done this weekend and early this week. We managed to finish the bed wood modification, bolt replacement, the interior door panels and handles, fixed some small wiring problems, and clamped down the fuel lines to the chassis. We also primed the oil pump, finished the fuel line attachment, filled the gas tank and got the truck running! It ran well considering the last time I had run it was September 2011. We are very close to having it ready for the Father's Day weekend drive! Here are some images. Attached Images __________________ Check out my project: 1972 Chevrolet Stepside- Shortbed http://67-72chevytrucks.com/vboard/s...d.php?t=392386 . . . . . . . . . . .__ . . . . . ______l__l\___ . . . . .l_[(O)]_____(O)]

06-13-2012, 02:07 AM	#90
whiteyandreddy Registered User Join Date: Jan 2010 Location: Erie, CO Posts: 83	Re: 1972 Stepside SWB Here are a couple more pictures of the nearly finished truck. There are a few more things to finish up, particularly in the engine bay, and detailing. I will be working to carpet installed next week. I want to make sure all of the wiring is OK before we cover it up with carpet. I am starting to see why people say the projects are never truly done. Attached Images __________________ Check out my project: 1972 Chevrolet Stepside- Shortbed http://67-72chevytrucks.com/vboard/s...d.php?t=392386 . . . . . . . . . . .__ . . . . . ______l__l\___ . . . . .l_[(O)]_____(O)]



Register or Log In To remove these advertisements.

06-13-2012, 02:10 AM	#91
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: 1972 Stepside SWB Truck looks GREAT! Nice job!!! __________________ Looking for a 67-72 swb or blazer project in or around VA.

06-13-2012, 06:08 AM	#92
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: 1972 Stepside SWB Very nice ! Posted via Mobile Device __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

06-13-2012, 10:10 AM	#93
67c10rustbuket Registered User Join Date: Apr 2011 Location: Mustang, Oklahoma Posts: 2,806	Re: 1972 Stepside SWB Congrats ! that is awesome I have one of those Boyd tanks also, they are VERY nice! __________________ Dan <---(my name) 67 SWB C10 project "GEORGIA"-59 Brookwood 2dr wag...Next project-03 Tahoe 4x4 5.3 family ride-07 Hondur Accord, commuter car

06-13-2012, 10:35 AM	#94
mcbassin Still Learning Join Date: Jul 2009 Location: Central Oklahoma Posts: 10,108	Re: 1972 Stepside SWB Your truck looks great! Love it! Posted via Mobile Device __________________ Mike "69 Short Wide" My Project 86 Silverado Landen's Project Instagram: @mcbassin My Website C/10 Club Oklahoma Facebook Group

07-13-2012, 12:46 AM	#95
whiteyandreddy Registered User Join Date: Jan 2010 Location: Erie, CO Posts: 83	Re: 1972 Stepside SWB Thanks for the kinds words. Sorry I haven't posted for a while. I have been working a lot, had computer problems and the truck was getting the carpet installed. I will post some new photos this weekend after some detailing. __________________ Check out my project: 1972 Chevrolet Stepside- Shortbed http://67-72chevytrucks.com/vboard/s...d.php?t=392386 . . . . . . . . . . .__ . . . . . ______l__l\___ . . . . .l_[(O)]_____(O)]

07-17-2012, 11:11 PM	#96
whiteyandreddy Registered User Join Date: Jan 2010 Location: Erie, CO Posts: 83	Re: 1972 Stepside SWB Here are some photos of the truck after a lot of detailing, taken on Saturday, at a local car show. Attached Images __________________ Check out my project: 1972 Chevrolet Stepside- Shortbed http://67-72chevytrucks.com/vboard/s...d.php?t=392386 . . . . . . . . . . .__ . . . . . ______l__l\___ . . . . .l_[(O)]_____(O)]

07-17-2012, 11:19 PM	#97
Pro Performance Registered User Join Date: Aug 2010 Location: AZ Posts: 3,069	Re: 1972 Stepside SWB Truck looks great!

07-17-2012, 11:42 PM	#98
insane04 Registered User Join Date: May 2012 Location: dallas ga Posts: 15	Re: 1972 Stepside SWB dam i love it!!

07-18-2012, 07:17 AM	#99
67c10rustbuket Registered User Join Date: Apr 2011 Location: Mustang, Oklahoma Posts: 2,806	Re: 1972 Stepside SWB PERFECT!! Excellent job man, must be great to be able to cruise it to a show! __________________ Dan <---(my name) 67 SWB C10 project "GEORGIA"-59 Brookwood 2dr wag...Next project-03 Tahoe 4x4 5.3 family ride-07 Hondur Accord, commuter car

07-18-2012, 02:34 PM	#100
Kregb Registered User Join Date: Nov 2011 Location: Erie, Colorado Posts: 9	Re: 1972 Stepside SWB Great to see the truck in person and talk to you. The pictures don't do the truck justice it looks much better in person. Thanks for letting me know you would have it at the show. I will make it a point to see any time I know you have it out, inspires me to work a little harder on mine.

Register or Log In To remove these advertisements.