The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > Info Center > FAQ Truck Tech

Web 67-72chevytrucks.com


 
 
Thread Tools Display Modes
Old 02-17-2014, 10:54 AM   #1
mattcrp1
Registered User
 
mattcrp1's Avatar
 
Join Date: May 2010
Location: Mountain House, CA
Posts: 555
Upper Control arm bushing replacement

Hi all I thought I would share how I installed my prothane control arm bushings. I bought them from AZproperformance, and it was a great price. These are the inserts and not the whole shell. I started with an initial clean up in the hot tank to get the crud off. As you can see from the pics my bushings were shot. I then removed the nuts and washers, hit the shaft and collar with PB blaster and mounted the arm in the vise.
Attached Images
     
__________________
My Chevy habit is paid for by Ford diesels...
Here is my SLOW LS install: http://67-72chevytrucks.com/vboard/s...55#post6456355
Caliper Rebuild: http://67-72chevytrucks.com/vboard/s...d.php?t=613748
Upper Control Arm Bushings: http://67-72chevytrucks.com/vboard/s...d.php?t=616974
IG mattcrp1
mattcrp1 is offline  
Old 02-17-2014, 11:01 AM   #2
mattcrp1
Registered User
 
mattcrp1's Avatar
 
Join Date: May 2010
Location: Mountain House, CA
Posts: 555
Re: Upper Control arm bushing replacement

Once in the vise and soaked with PB blaster, I break the cross shaft free from the collar and bushings. After it moves freely I begin to cut away the rubber from the collar I grab my drill and punch a few holes in the bushing. Once a few holes are drilled I can grab the collar with a pair of channel locks and pull it out.
Attached Images
     
__________________
My Chevy habit is paid for by Ford diesels...
Here is my SLOW LS install: http://67-72chevytrucks.com/vboard/s...55#post6456355
Caliper Rebuild: http://67-72chevytrucks.com/vboard/s...d.php?t=613748
Upper Control Arm Bushings: http://67-72chevytrucks.com/vboard/s...d.php?t=616974
IG mattcrp1
mattcrp1 is offline  
Old 02-17-2014, 11:14 AM   #3
mattcrp1
Registered User
 
mattcrp1's Avatar
 
Join Date: May 2010
Location: Mountain House, CA
Posts: 555
Re: Upper Control arm bushing replacement

Once the collar is out a simple pick or screw driver can remove the old bushing. After the bushing is out the cross shaft slips out the old shell. Once the shaft is out of the way simply knock out the other collar and remove the other bushing the same way. Now a little more cleaning and I am almost ready to re assemble.
Attached Images
     
__________________
My Chevy habit is paid for by Ford diesels...
Here is my SLOW LS install: http://67-72chevytrucks.com/vboard/s...55#post6456355
Caliper Rebuild: http://67-72chevytrucks.com/vboard/s...d.php?t=613748
Upper Control Arm Bushings: http://67-72chevytrucks.com/vboard/s...d.php?t=616974
IG mattcrp1
mattcrp1 is offline  
Old 02-17-2014, 11:31 AM   #4
mattcrp1
Registered User
 
mattcrp1's Avatar
 
Join Date: May 2010
Location: Mountain House, CA
Posts: 555
Re: Upper Control arm bushing replacement

Now for the reassembly, I found that if you lubricate the inside of the shell with the supplied lube and a little bit of transprep or petroleum jelly type product the bushings will go in a little easier. Also when installing the bushings I found it easier to not have the gold color collar fully in the new bushing but maybe hanging out about 3/4-1 inch. Now when pressing the bushing in take care not to move the shell in the arm.
Attached Images
     
__________________
My Chevy habit is paid for by Ford diesels...
Here is my SLOW LS install: http://67-72chevytrucks.com/vboard/s...55#post6456355
Caliper Rebuild: http://67-72chevytrucks.com/vboard/s...d.php?t=613748
Upper Control Arm Bushings: http://67-72chevytrucks.com/vboard/s...d.php?t=616974
IG mattcrp1
mattcrp1 is offline  
Old 02-17-2014, 11:46 AM   #5
mattcrp1
Registered User
 
mattcrp1's Avatar
 
Join Date: May 2010
Location: Mountain House, CA
Posts: 555
Re: Upper Control arm bushing replacement

Once one side is in and seated the cross shaft is lubricated and installed. At this point I install the nuts and washers to help drive in the bushing. I will also use a spacer under the washer as to give room for the collar to not be totally in the bushing as it is being installed. Don't forget to lubricate the inside of the shell and not seat the collar in the bushing. I also will mount the arm in the vise by the cross shaft and use a big socket and hammer to drive the bushing home. Once seated you are done and there you have it, R/R of control arm bushings. The lowers are the same and some people use a torch to do part of the job I just showed, I did these at work and the guys in the stalls next to me don't like the smell. LOL I hope this helped some one.
Attached Images
   
__________________
My Chevy habit is paid for by Ford diesels...
Here is my SLOW LS install: http://67-72chevytrucks.com/vboard/s...55#post6456355
Caliper Rebuild: http://67-72chevytrucks.com/vboard/s...d.php?t=613748
Upper Control Arm Bushings: http://67-72chevytrucks.com/vboard/s...d.php?t=616974
IG mattcrp1
mattcrp1 is offline  
Old 02-18-2014, 01:17 PM   #6
Pro Performance
Registered User
 
Pro Performance's Avatar
 
Join Date: Aug 2010
Location: AZ
Posts: 3,069
Re: Upper Control arm bushing replacement

Very nice write-up and thanks for sharing!
Pro Performance is offline  
Old 06-04-2014, 12:36 PM   #7
82ZZZR
Registered User
 
Join Date: Aug 2008
Location: PEORIA,IL
Posts: 73
Re: Upper Control arm bushing replacement

Agreed, nice write up.
82ZZZR is offline  
Old 08-08-2014, 04:19 AM   #8
Bigdogg
Registered User
 
Join Date: May 2014
Location: mount carmel, tn
Posts: 10
Re: Upper Control arm bushing replacement

Does anyone know where i can buy some lower control arms for my 81 C10 truck 2wheel drive? I have bought the upper ones new and now im having trouble locating new lower control arms.All help apprecaited. my email address is tjavery@eastman.com thanks
Bigdogg is offline  
Old 08-08-2014, 09:37 AM   #9
82ZZZR
Registered User
 
Join Date: Aug 2008
Location: PEORIA,IL
Posts: 73
Re: Upper Control arm bushing replacement

I have some used ones that need new bushings, or are you looking for ones ready to bolt on?
82ZZZR is offline  
Old 10-26-2014, 09:55 AM   #10
Slowlane37
Registered User
 
Join Date: Oct 2014
Location: Richardson, Texas
Posts: 2
Re: Upper Control arm bushing replacement

Hi Matt,

Nice write up - but I lost you after the vice picture of the prothane bushing. Would you please let me know what I got wrong below:

(black bushing and vice install pic) Seating a greased black bushing by itself. No brass bushing yet. Be sure not to move the control arm shell in the control arm.

(C-clamp picture) Pressing in a greased brass bushing into the previously installed black bushing.

(control arm, shaft, bushings pic) Once one side is complete (black bushing installed into shell, brass bushing installed into black)

clean, lube and insert cross shaft.

apply washer and nut on finished side.

lube black bushing and get started into other side until nut and washer can be applied to press greased black bushing into place.

Remove the incomplete sides nut and washer, slide greased busing onto shaft and again use nut and washer to seat brass bushing into black busing.

?
Slowlane37 is offline  
 

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 01:39 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com