The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Suspension

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 01-04-2018, 12:01 PM   #1
robnolimit
Senior Member
 
robnolimit's Avatar
 
Join Date: Jul 2010
Location: Dandridge, Tn. USA
Posts: 2,183
No Limit Square Body 4-bar

We have now finished our first production run of Square Body FatBar 4-bar systems. Two years of testing and fitment checks have paid off well. This may be our best FatBar system yet, with the ride height, roll center and anti-squat matched perfectly to the truck.

These kits are as complete as we could make them to help with an easy install. All of the chassis side brackets fit OE holes in the chassis. An aluminum 'C' notch template (no flimsy paper) makes locating the notch cut easy and accurate. All hardware is grade-8. You get: Chassis side 4-Bar mounting brackets, integrated 'C' notch with upper coil-over mounts, notch brace crossmember with panhard bar mount and brake line tab, Axle mounts for coil-overs, 4-bars and panhard mount, FatBars and panhard bar with stainless adjusters, Coil-over shocks and springs and all hardware and instructions. The complete kit is priced at $1590.

There are a few things to note.

* Ride height is adjustable. Drop from stock height is appx 4" to 7"

* This kit fits Short bed and Longbed, but not Blazer. We are working on it.

* The four bars and coil-overs are outboard. Total space required is 4" out from the frame. this is about 3/4" more room than the leaf. You can widen the tubb to get 16" of tire clearance.

* The front 4-bar mount locates to the front side of the OE leaf mount holes. This is needed to fit the longer bars to get the geometry correct. Due to the bar length, OE "outboard" mounted fuel tanks will NOT fit.

* Yes, your forum discount applies.
Attached Images
 
__________________
GoodGuys 2012 Pro-Truck Champion
2012 Truckin' Throwdown Champion
GoodGuys 2011 National Champion
2011 Truckin' Throwdown Champion
GoodGuys 2010 National Champion

Proud to put our products up against all others!
robnolimit is offline   Reply With Quote
Old 01-04-2018, 08:00 PM   #2
SCOTI
Registered User
 
SCOTI's Avatar
 
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 17,474
Re: No Limit Square Body 4-bar

Nice.
__________________
67SWB-B.B.RetroRod
64SWB-Recycle
89CCDually-Driver/Tow Truck
99CCSWB Driver
All Fleetsides

Building a small, high rpm engine
with the perfect bore, stroke and rod ratio is very impressive...
like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar.

Cubic inches is like Indiana Jones with a cheap pistol....
SCOTI is offline   Reply With Quote
Old 01-05-2018, 01:44 PM   #3
tinydb84
Registered User
 
tinydb84's Avatar
 
Join Date: Jul 2009
Location: San Jose Ca
Posts: 2,554
Re: No Limit Square Body 4-bar

Looks nice. Any installed pics?
__________________
David
Used parts build: http://67-72chevytrucks.com/vboard/s...d.php?t=638991
My brother's Nova: http://www.67-72chevytrucks.com/vboa...d.php?t=727985
Rear suspension rework: http://www.67-72chevytrucks.com/vboa...d.php?t=750557
Instagram: Tinydb84
tinydb84 is offline   Reply With Quote
Old 01-07-2018, 05:44 PM   #4
dec010974
Registered User
 
dec010974's Avatar
 
Join Date: Oct 2012
Location: Miami, Florida
Posts: 689
Re: No Limit Square Body 4-bar

No Limit makes it hard to decided what suspension is best. They have som many good options that are reasonably price.
dec010974 is offline   Reply With Quote
Old 01-08-2018, 04:25 PM   #5
moregrip
Registered User
 
moregrip's Avatar
 
Join Date: Dec 2008
Location: Las Vegas, NV
Posts: 638
Re: No Limit Square Body 4-bar

Quote:
Originally Posted by robnolimit View Post
We have now finished our first production run of Square Body FatBar 4-bar systems. Two years of testing and fitment checks have paid off well. This may be our best FatBar system yet, with the ride height, roll center and anti-squat matched perfectly to the truck.

These kits are as complete as we could make them to help with an easy install. All of the chassis side brackets fit OE holes in the chassis. An aluminum 'C' notch template (no flimsy paper) makes locating the notch cut easy and accurate. All hardware is grade-8. You get: Chassis side 4-Bar mounting brackets, integrated 'C' notch with upper coil-over mounts, notch brace crossmember with panhard bar mount and brake line tab, Axle mounts for coil-overs, 4-bars and panhard mount, FatBars and panhard bar with stainless adjusters, Coil-over shocks and springs and all hardware and instructions. The complete kit is priced at $1590.

There are a few things to note.

* Ride height is adjustable. Drop from stock height is appx 4" to 7"

* This kit fits Short bed and Longbed, but not Blazer. We are working on it.

* The four bars and coil-overs are outboard. Total space required is 4" out from the frame. this is about 3/4" more room than the leaf. You can widen the tubb to get 16" of tire clearance.

* The front 4-bar mount locates to the front side of the OE leaf mount holes. This is needed to fit the longer bars to get the geometry correct. Due to the bar length, OE "outboard" mounted fuel tanks will NOT fit.

* Yes, your forum discount applies.
this looks awesome! same relative performance from 4" to 7"?
__________________
Always a project truck
moregrip is offline   Reply With Quote
Old 01-20-2018, 02:24 PM   #6
Goats86
Registered User
 
Join Date: Dec 2010
Location: Waxahachie, Texas
Posts: 129
Re: No Limit Square Body 4-bar

Rob, Do you have any installed pictures? I am running a 31 gallon blazer fuel tank and needing to see if this will fit in with the tank.
Goats86 is offline   Reply With Quote
Old 03-20-2018, 09:27 PM   #7
Goats86
Registered User
 
Join Date: Dec 2010
Location: Waxahachie, Texas
Posts: 129
Re: No Limit Square Body 4-bar

What is the forum discount?
Goats86 is offline   Reply With Quote
Old 03-21-2018, 10:07 AM   #8
robnolimit
Senior Member
 
robnolimit's Avatar
 
Join Date: Jul 2010
Location: Dandridge, Tn. USA
Posts: 2,183
Re: No Limit Square Body 4-bar

Quote:
Originally Posted by moregrip View Post
this looks awesome! same relative performance from 4" to 7"?
Yes. Because our bars are adjustable (multiple mounting points) you can get the I.C. and Anti-Squat in range at varying ride heights.
__________________
GoodGuys 2012 Pro-Truck Champion
2012 Truckin' Throwdown Champion
GoodGuys 2011 National Champion
2011 Truckin' Throwdown Champion
GoodGuys 2010 National Champion

Proud to put our products up against all others!
robnolimit is offline   Reply With Quote
Old 03-21-2018, 10:09 AM   #9
robnolimit
Senior Member
 
robnolimit's Avatar
 
Join Date: Jul 2010
Location: Dandridge, Tn. USA
Posts: 2,183
Re: No Limit Square Body 4-bar

Quote:
Originally Posted by Goats86 View Post
Rob, Do you have any installed pictures? I am running a 31 gallon blazer fuel tank and needing to see if this will fit in with the tank.
There is about 24"/25" from our crossmember back for a tank. It would be close. If you still have the OE brake line tab/arm holding your brake line (out from the chassis, behind the rear axle) then it would fit. Our crossmember has a tab to replace the OE arm, in the same location.
__________________
GoodGuys 2012 Pro-Truck Champion
2012 Truckin' Throwdown Champion
GoodGuys 2011 National Champion
2011 Truckin' Throwdown Champion
GoodGuys 2010 National Champion

Proud to put our products up against all others!
robnolimit is offline   Reply With Quote
Old 03-21-2018, 10:11 AM   #10
robnolimit
Senior Member
 
robnolimit's Avatar
 
Join Date: Jul 2010
Location: Dandridge, Tn. USA
Posts: 2,183
Re: No Limit Square Body 4-bar

Quote:
Originally Posted by Goats86 View Post
What is the forum discount?
10%. Also, we will be at the C10 Nationals in Ft. Worth in May. If you are going, you can place your order ahead of time and we will deliver to the show at no charge.
__________________
GoodGuys 2012 Pro-Truck Champion
2012 Truckin' Throwdown Champion
GoodGuys 2011 National Champion
2011 Truckin' Throwdown Champion
GoodGuys 2010 National Champion

Proud to put our products up against all others!
robnolimit is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:58 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2018, vBulletin Solutions Inc.
Copyright 1997-2013 67-72chevytrucks.com