The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 06-07-2019, 10:11 AM   #626
70STOVEBOLT
Broke
 
70STOVEBOLT's Avatar
 
Join Date: Jun 2005
Location: Winona Lake, IN
Posts: 4,804
Re: What did you do to your truck today.The 3rd chapter

Quote:
Originally Posted by RodnRudy View Post
I did the 500 mile break in oil and filter change today. I'm using NAPA 10/30 with Lucas Oil additive that has the zinc in it. Also replaced the coil in the HEI, I've been having problems with the engine not wanting to start after driving a while and getting good and warm. I've replaced two modules and no luck so I'm trying a different coil.
If you have an Edelbrock carb without an insulator gasket, the fuel is probably boiling out of the bowl. I had this problem with the stock cast iron intake until I put an insulator gasket between the intake and the spacer plate.
__________________
70 SWB 250 TH400 "The Needy Beast"
200,000 Mile Club
Drum Brake Club
Daily Driver Club
Owner installed options:
Front Sway Bar
Power Steering
Power Brakes
Cigar Lighter
Courtesy Lights
Deluxe Side Markers
Wiper Delay
70STOVEBOLT is online now   Reply With Quote
Old 06-07-2019, 11:12 AM   #627
RodnRudy
Senior Member
 
RodnRudy's Avatar
 
Join Date: Oct 2014
Location: New Palestine In
Posts: 708
Re: What did you do to your truck today.The 3rd chapter

Quote:
Originally Posted by 70STOVEBOLT View Post
If you have an Edelbrock carb without an insulator gasket, the fuel is probably boiling out of the bowl. I had this problem with the stock cast iron intake until I put an insulator gasket between the intake and the spacer plate.
I've got a phenolic 1/2" spacer under the carb so I don't have a fuel boiling problem. When this happened I checked for spark and had none, and then when the engine cooled down some I'd get the spark back and it'd run. I did a test run yesterday with the replacement coil and it started right up even though the engine was hot. What irks me is that this is a new GM distributor but of course it has a made in Mexico sticker on it.
__________________
Phil
"Money is only a tool to create and achieve what you want most in life"
PayPal: rodnrudy@comcast.net
RodnRudy is offline   Reply With Quote
Old 06-07-2019, 12:41 PM   #628
70STOVEBOLT
Broke
 
70STOVEBOLT's Avatar
 
Join Date: Jun 2005
Location: Winona Lake, IN
Posts: 4,804
Re: What did you do to your truck today.The 3rd chapter

Quote:
Originally Posted by RodnRudy View Post
I've got a phenolic 1/2" spacer under the carb so I don't have a fuel boiling problem. When this happened I checked for spark and had none, and then when the engine cooled down some I'd get the spark back and it'd run. I did a test run yesterday with the replacement coil and it started right up even though the engine was hot. What irks me is that this is a new GM distributor but of course it has a made in Mexico sticker on it.
Sounds like you are on the right track then. Hope the new coil solves the issue.
__________________
70 SWB 250 TH400 "The Needy Beast"
200,000 Mile Club
Drum Brake Club
Daily Driver Club
Owner installed options:
Front Sway Bar
Power Steering
Power Brakes
Cigar Lighter
Courtesy Lights
Deluxe Side Markers
Wiper Delay
70STOVEBOLT is online now   Reply With Quote
Old 06-07-2019, 04:57 PM   #629
Steeveedee
Senior Member
 
Steeveedee's Avatar
 
Join Date: Jan 2013
Location: Simi Valley, CA
Posts: 3,048
Re: What did you do to your truck today.The 3rd chapter

Mexico doesn't have the same import requirements we do. A part can be imported from China to Mexico and then shipped to the US as "Made in Mexico".
__________________
'70 Chevy 3/4T Longhorn CST 400/400/3.54 Custom Camper

"Orange Acres"
Steeveedee is offline   Reply With Quote
Old 06-09-2019, 10:31 AM   #630
Quikshft
Registered User
 
Quikshft's Avatar
 
Join Date: Oct 2010
Location: Kingsburg, Ca.
Posts: 78
Re: What did you do to your truck today.The 3rd chapter

Yesterday I added back most of the trim/bumpers etc after completing the paint job. Still have a lot of molding to put on to complete the two tone look.
Attached Images
 
Quikshft is offline   Reply With Quote
Old 06-09-2019, 11:50 AM   #631
SoCoC10
Senior Member
 
SoCoC10's Avatar
 
Join Date: Nov 2014
Location: Colorado
Posts: 2,755
Re: What did you do to your truck today.The 3rd chapter

I think I might be done with this one. Nice distraction while the K5 was back at the paint shop. Wanted to make a mini version of my 71 C10 Cheyenne SWB. There's more pictures and details in the "Our Stuff in scale" area.
Attached Images
     
__________________
07' Extcab Silverado Z71 Silver Birch, 5.3L HO
71' Cheyenne C10 Hugger Orange on Saddle SWB
Besides these two, too Many to count

Last edited by SoCoC10; 06-09-2019 at 01:03 PM.
SoCoC10 is offline   Reply With Quote
Old 06-09-2019, 02:29 PM   #632
InNeedofaDelorean
Registered User
 
Join Date: Oct 2007
Location: Raytown, Missouri
Posts: 123
Re: What did you do to your truck today.The 3rd chapter

Got dual exhaust put on, 2 inch pipe, 18 inch Cherry Bombs, and lucked into finding a set of slots from the cool dude I bought the truck from. Getting closer to that 70's look that I want.



__________________
1972 GMC 3/4 2wd "Phantom"
InNeedofaDelorean is offline   Reply With Quote
Old 06-09-2019, 09:17 PM   #633
NoStopN
Registered User
 
NoStopN's Avatar
 
Join Date: Jul 2016
Location: Murfreesboro, TN
Posts: 202
Re: What did you do to your truck today.The 3rd chapter

I took mine down the road for a photo op.

__________________
1969 GMC 2500. 250 I6, 4-speed w/ granny low.
2019 Ram 1500. Hemi 5.7L V8, crew cab, vinyl bench seats, snow white
NoStopN is offline   Reply With Quote
Old 06-09-2019, 09:52 PM   #634
tdangle
Senior Member
 
tdangle's Avatar
 
Join Date: Mar 2005
Location: Jurupa Valley, Ca
Posts: 512
Re: What did you do to your truck today.The 3rd chapter

Upped the initial timing from 8 to 14 degrees to make total amount 36 degrees. Much better throttle response. Need to get a tach that goes to at least 4K rpm to see when total advance is all in. I'm thinking that I need to recurve the HEI distributor
__________________
Terry

1970 C20 Custom Camper, 350/2004R, Dana 60, factory AC, side tool box
tdangle is offline   Reply With Quote
Old 06-11-2019, 12:38 PM   #635
weq92f
Senior Member
 
Join Date: Oct 2016
Location: Dallas Texas
Posts: 1,484
Re: What did you do to your truck today.The 3rd chapter

.
Pulled out the old dizzy and prepped the new one for install...

MSD 8361:

Stock blue bushing will stay there for 21* of mech timing.
Placed one light blue and one light silver spring on the mech assembly, this should bring all 21* of mech timing in just under 2500.

Will stab it in soon...

-klb
__________________
67 C10 fleet fuel injected '70 402, 700r4, 3.73 posi
07 335 sport turbo 6sp
94 Trans Am GT LT1 6sp posi -- sold after 22yrs
99 540 sport V8 6sp -- sold
73 240z L24 4sp -- given to friend
68 C10 step 350/350 3.73 open -- sold
weq92f is offline   Reply With Quote
Old 06-11-2019, 05:16 PM   #636
72c20customcamper
Registered User
 
72c20customcamper's Avatar
 
Join Date: Jul 2018
Location: Napanoch new york
Posts: 901
Re: What did you do to your truck today.The 3rd chapter

Since I can't paint my bed because my compressor went south. Can't complain its 27 years old . Motor is a GE 5 HP made in USA . Keeping that and the pump tank is shot. But I worked on the passenger door today. Inner door is all fixed and it fits very well little more body work and I'll paint it .

Picking up the new one tomorrow at Tractor supply. Getting the 80 gallon ingersal rand .
Attached Images
 
__________________
Mark
72 c20 custom camper Husky edition,66 SS396 Chevelle 1964 Hawk, 63 Avanti,62 lark
1969 AMX ,02 Springer. 03 anniversary Fatboy.
81 Honda automatic 1600 miles
2012 Road Glide Ultra 2015 Honda Goldwing
1968 c20 stepside
72c20customcamper is online now   Reply With Quote
Old 06-11-2019, 06:40 PM   #637
WorkinLonghorn
Registered User
 
WorkinLonghorn's Avatar
 
Join Date: Dec 2006
Location: Studio City, Calif.
Posts: 2,607
Re: What did you do to your truck today.The 3rd chapter

Changed the oil and filter replacing 10-30 with 10-40.

Replaced dimmer switch with ACDELCO D808 (Made in Taiwan-the first one i ordered didn't work).

Reconnected the wiper switch connector that has been off for 2 years now that the rain is done for the year and I won't need it.

This is fun, if it wasn't 96 out I'd do more. -BA
__________________
'69 GMC C2500 Custom Camper, 8 1/2' bed (same as Chevy "Longhorn"), 350 ci. mild RV cam, NP 435 CR 4spd. Trans., 3.73 Dana-60 open.Camper and Trailer wiring, PS, PB, AC, tach , three gas tanks, 2nd owner, Work-Truck supreme. Best $300 I ever spent.

Last edited by WorkinLonghorn; 06-11-2019 at 06:54 PM.
WorkinLonghorn is online now   Reply With Quote
Old 06-12-2019, 09:58 AM   #638
tdangle
Senior Member
 
tdangle's Avatar
 
Join Date: Mar 2005
Location: Jurupa Valley, Ca
Posts: 512
Re: What did you do to your truck today.The 3rd chapter

Quote:
Originally Posted by WorkinLonghorn View Post
Changed the oil and filter replacing 10-30 with 10-40.

Replaced dimmer switch with ACDELCO D808 (Made in Taiwan-the first one i ordered didn't work).

Reconnected the wiper switch connector that has been off for 2 years now that the rain is done for the year and I won't need it.

This is fun, if it wasn't 96 out I'd do more. -BA
It has been hot this week so far!!
__________________
Terry

1970 C20 Custom Camper, 350/2004R, Dana 60, factory AC, side tool box
tdangle is offline   Reply With Quote
Old 06-12-2019, 12:46 PM   #639
Steeveedee
Senior Member
 
Steeveedee's Avatar
 
Join Date: Jan 2013
Location: Simi Valley, CA
Posts: 3,048
Re: What did you do to your truck today.The 3rd chapter

Yup summer finally hit. It's been really nice up to now. The AC ran for the first time yesterday. I'm hoping that that means we're going to have a cooler summer again.
__________________
'70 Chevy 3/4T Longhorn CST 400/400/3.54 Custom Camper

"Orange Acres"
Steeveedee is offline   Reply With Quote
Old Today, 06:14 PM   #640
Astro-Balls
Registered User
 
Astro-Balls's Avatar
 
Join Date: Feb 2019
Location: CA
Posts: 154
Re: What did you do to your truck today.The 3rd chapter

Had the '68 Steam Cleaned today, took off about 100 lbs of dirt and grease..
Now i can see where all of the Zerk fittings are..

__________________
1968 C20 Fleetside 396 4sp PS PB AC CST

https://www.youtube.com/watch?v=RWK8GgWD4uA
Astro-Balls is online now   Reply With Quote
Old Today, 06:16 PM   #641
ohboy321
Steve
 
ohboy321's Avatar
 
Join Date: Aug 2015
Location: Dunbarton, NH
Posts: 169
Re: What did you do to your truck today.The 3rd chapter

Painted some of the parts needed to put the engine bay back together, but the best part was getting a 67 steering wheel in the mail. My 67 currently has a 70 style, and I can't wait to put the correct one in. It was a good deal on a "buy it now" on the auction site, and the bonus was the nice horn button with no broken tabs that came with it. Plus it has all the internals to make it go beep! Will eventually restore it in black, but will install as-is to enjoy for now. Benny likes it...
Attached Images
  
ohboy321 is online now   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:32 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.
Copyright 1997-2013 67-72chevytrucks.com