Project: ALTER-K-TION ('57 GMC Quad Cab) - Page 5 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

addicted2dunes · 05-07-2010, 12:15 AM

Cut some firewall fillers and the lower B-pillar boxes today. Still got to bend the boxes a little more but can't finish them on the brake, gotta do it by hand.

]

Plus, everyone has to have a cool mailbox flag right?

Fred T · 05-07-2010, 11:14 PM

Quote:

Plus, everyone has to have a cool mailbox flag right?

That is cool. Looks good enough to clear coat and leave the burnt flames as they are.

addicted2dunes · 05-07-2010, 11:16 PM

Quote:

Originally Posted by Fred T

That is cool. Looks good enough to clear coat and leave the burnt flames as they are.

I'm think'n I'll cut it out of stainless and just leave it as it comes out.

addicted2dunes · 05-08-2010, 01:05 AM

Welp, tonight wasn't that great. Got one B-pillar brace bent up and half way welded in....

Then test fitted the door again. For some reason it was really close to the B-pillar support. Measured everything again, good. Measured again, good. Got confused for a while. Cussed a bit. Measured again..... AH HAH..... The front driver's side A-pillar is twisted, I should have noticed that just by looking at the hinge pockets. Seems to me like someone had their door open, backed up and wacked the door. Which then broke the pin in the hinge, bashed the cab, and then twisted the A-pillar.

I know what I'm doing tomorrow now..... Replacing an A-pillar... Wa-hoo

VA72C10 · 05-08-2010, 08:24 AM

Keep at it....It's coming together nicely (even if you have to take parts of it back apart for it to come together right

)

addicted2dunes · 05-10-2010, 01:00 AM

Got the rear of the front cab mounted up yesterday. Almost chopped my head off with the whole cab back..... Hammering on a large piece of metal while clamped in and your head under a sharp cut piece of sheetmetal = no good.

I still have to replace the front A-pillar but I got the donor section cut from another one of my cabs, just need to cut the bad section out of this cab.... way to many spotwelds.....

Also went junkyard hopping today and think I have found my donor roof panel with a giant sunroof. AWESOME!

Also got a few firewall patches in place. Plan for the beginning of this week is to get the A-pillar replaced, B-pillars welded up, doors hung. I have to work on my Jeep the end of this week and the weekend. I gotta finish something around here, right?

addicted2dunes · 05-11-2010, 11:53 PM

My projects been relocated in the "projects and build forum"? This isn't a project, is it?

addicted2dunes · 05-11-2010, 11:57 PM

New A-pillar has been stripped of all it's excess sheetmetal, cleaned, sealed, and replaced the lowest cage nut for the door hinge. It's all ready to go in now.... Just trying to figure out whether I should clean everything up while it is out before welding the new one back in.
I thought I'd have to replace the lower hinge area but this one was in great shape minus the lowest cage nut (easy fix though). Had to do a little metal work around both hinge holes but nothing major, just a little straightening.

addicted2dunes · 05-12-2010, 11:35 PM

I sit quiet and whack myself on the head for the hurt I'm getting myself into on this build.

addicted2dunes · 05-13-2010, 01:14 AM

Cut and bent up a few more goodies today. Got the C-channel step supports and the door latch plates done (using the Dodge latches).

And here's the new A-pillar I need to get in....

RRinWT · 05-13-2010, 09:01 PM

Here's some inspiration for you. This truck was for sale up in the Midwest a few years ago. It had the frame and drivetrain from a late model Chevy HD3500. The guy wanted $15K for it and said he'd NEVER build another one. TOO many hours of fabrication. Enjoy.

Rob

addicted2dunes · 05-15-2010, 12:47 AM

Quote:

Originally Posted by RRinWT

Here's some inspiration for you. This truck was for sale up in the Midwest a few years ago. It had the frame and drivetrain from a late model Chevy HD3500. The guy wanted $15K for it and said he'd NEVER build another one. TOO many hours of fabrication. Enjoy.

Rob

Looks like a beautiful truck. I often worry about the "if's." If I got t-boned, If I took out the custom dually fenders, If If If......

Definitely a lot of work to build this truck.

Project is on hold until the Jeep is done.... 1 or 2 weeks.

ghettoluxury · 05-18-2010, 06:16 PM

looks great, keep up the good work!

addicted2dunes · 05-21-2010, 12:23 AM

The Jeep is kicking my @$$. I thought it'd be a quick pull cage, finish welding cage, paint cage, patch rust in tub, Line-X tub, reinstall cage, reinstall interior..... Well the rust repair has taken me about a week. Started masking the tub to Line-X and it started to peel the paint, so now I have to repaint the passenger side of the Jeep.

Hang tight folks, I'll be back on this project as quick as I can......

addicted2dunes · 05-29-2010, 11:10 PM

Jeep is done! Back on this project starting on Mon., have to play at the local car show tomorrow, so one more day! Yeah, maybe I can get something accomplished!

addicted2dunes · 05-31-2010, 03:10 PM

A-pillar replaced, front cab back in (still have to cut out a lot more), and driver's door hung.

VA72C10 · 05-31-2010, 04:55 PM

nice progress!

addicted2dunes · 06-09-2010, 01:46 AM

And now we're on long term hold.......

**FRENCHBLUE72** · 06-09-2010, 08:33 PM

Crap what happened???

addicted2dunes · 06-10-2010, 12:30 AM

Oh, nothing bad..... I guess I worded that a little rough, just finishing up other projects around the house and other vehicles.

addicted2dunes · 06-17-2010, 01:10 AM

Been working on this a little bit, nothing body wise though. My boss at the Streetrod shop I work at has been tediously banging out the dings and dents in all the trim to get it all ready for rechroming.

addicted2dunes · 06-21-2010, 02:07 AM

sak778 · 07-06-2010, 10:37 AM

Where'd all the pic's go????

addicted2dunes · 08-09-2010, 12:00 AM

Quote:

Originally Posted by sak778

Where'd all the pic's go????

I figured out what happened.... I changed the names of all the pics so the file names changed too. I don't remember what goes where. I am slowly updating the threads with the pics.

**FRENCHBLUE72** · 07-06-2010, 08:04 PM

lOOKS LIKE PHOTO BUCKET PROBLEMS..

05-07-2010, 12:15 AM	#1
addicted2dunes Insane In The Membrane Join Date: Jan 2010 Location: Orcutt, CA Posts: 446	Re: Project: ALTER-K-TION ('57 GMC Quad Cab) Cut some firewall fillers and the lower B-pillar boxes today. Still got to bend the boxes a little more but can't finish them on the brake, gotta do it by hand. ] Plus, everyone has to have a cool mailbox flag right? __________________ Cameron Gunlock Project: ALTER-K-TION ('57 GMC Quad Cab) http://67-72chevytrucks.com/vboard/s...d.php?t=393750 Last edited by addicted2dunes; 11-23-2010 at 08:26 PM.

05-08-2010, 01:05 AM	#4
addicted2dunes Insane In The Membrane Join Date: Jan 2010 Location: Orcutt, CA Posts: 446	Re: Project: ALTER-K-TION ('57 GMC Quad Cab) Welp, tonight wasn't that great. Got one B-pillar brace bent up and half way welded in.... Then test fitted the door again. For some reason it was really close to the B-pillar support. Measured everything again, good. Measured again, good. Got confused for a while. Cussed a bit. Measured again..... AH HAH..... The front driver's side A-pillar is twisted, I should have noticed that just by looking at the hinge pockets. Seems to me like someone had their door open, backed up and wacked the door. Which then broke the pin in the hinge, bashed the cab, and then twisted the A-pillar. I know what I'm doing tomorrow now..... Replacing an A-pillar... Wa-hoo __________________ Cameron Gunlock Project: ALTER-K-TION ('57 GMC Quad Cab) http://67-72chevytrucks.com/vboard/s...d.php?t=393750 Last edited by addicted2dunes; 11-23-2010 at 08:29 PM.

05-08-2010, 08:24 AM	#5
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: Project: ALTER-K-TION ('57 GMC Quad Cab) Keep at it....It's coming together nicely (even if you have to take parts of it back apart for it to come together right ) __________________ Looking for a 67-72 swb or blazer project in or around VA.

05-10-2010, 01:00 AM	#6
addicted2dunes Insane In The Membrane Join Date: Jan 2010 Location: Orcutt, CA Posts: 446	Re: Project: ALTER-K-TION ('57 GMC Quad Cab) Got the rear of the front cab mounted up yesterday. Almost chopped my head off with the whole cab back..... Hammering on a large piece of metal while clamped in and your head under a sharp cut piece of sheetmetal = no good. I still have to replace the front A-pillar but I got the donor section cut from another one of my cabs, just need to cut the bad section out of this cab.... way to many spotwelds..... Also went junkyard hopping today and think I have found my donor roof panel with a giant sunroof. AWESOME! Also got a few firewall patches in place. Plan for the beginning of this week is to get the A-pillar replaced, B-pillars welded up, doors hung. I have to work on my Jeep the end of this week and the weekend. I gotta finish something around here, right? __________________ Cameron Gunlock Project: ALTER-K-TION ('57 GMC Quad Cab) http://67-72chevytrucks.com/vboard/s...d.php?t=393750 Last edited by addicted2dunes; 05-10-2010 at 01:00 AM.

05-11-2010, 11:53 PM	#7
addicted2dunes Insane In The Membrane Join Date: Jan 2010 Location: Orcutt, CA Posts: 446	Re: Project: ALTER-K-TION ('57 GMC Quad Cab) My projects been relocated in the "projects and build forum"? This isn't a project, is it? __________________ Cameron Gunlock Project: ALTER-K-TION ('57 GMC Quad Cab) http://67-72chevytrucks.com/vboard/s...d.php?t=393750 Last edited by addicted2dunes; 05-11-2010 at 11:53 PM.

05-11-2010, 11:57 PM	#8
addicted2dunes Insane In The Membrane Join Date: Jan 2010 Location: Orcutt, CA Posts: 446	Re: Project: ALTER-K-TION ('57 GMC Quad Cab) New A-pillar has been stripped of all it's excess sheetmetal, cleaned, sealed, and replaced the lowest cage nut for the door hinge. It's all ready to go in now.... Just trying to figure out whether I should clean everything up while it is out before welding the new one back in. I thought I'd have to replace the lower hinge area but this one was in great shape minus the lowest cage nut (easy fix though). Had to do a little metal work around both hinge holes but nothing major, just a little straightening. __________________ Cameron Gunlock Project: ALTER-K-TION ('57 GMC Quad Cab) http://67-72chevytrucks.com/vboard/s...d.php?t=393750

05-12-2010, 11:35 PM	#9
addicted2dunes Insane In The Membrane Join Date: Jan 2010 Location: Orcutt, CA Posts: 446	Re: Project: ALTER-K-TION ('57 GMC Quad Cab) I sit quiet and whack myself on the head for the hurt I'm getting myself into on this build. __________________ Cameron Gunlock Project: ALTER-K-TION ('57 GMC Quad Cab) http://67-72chevytrucks.com/vboard/s...d.php?t=393750

05-13-2010, 01:14 AM	#10
addicted2dunes Insane In The Membrane Join Date: Jan 2010 Location: Orcutt, CA Posts: 446	Re: Project: ALTER-K-TION ('57 GMC Quad Cab) Cut and bent up a few more goodies today. Got the C-channel step supports and the door latch plates done (using the Dodge latches). And here's the new A-pillar I need to get in.... __________________ Cameron Gunlock Project: ALTER-K-TION ('57 GMC Quad Cab) http://67-72chevytrucks.com/vboard/s...d.php?t=393750 Last edited by addicted2dunes; 11-23-2010 at 08:30 PM.

05-13-2010, 09:01 PM	#11
RRinWT Registered User Join Date: Apr 2010 Location: Odessa, TX Posts: 11	Re: Project: ALTER-K-TION ('57 GMC Quad Cab) Here's some inspiration for you. This truck was for sale up in the Midwest a few years ago. It had the frame and drivetrain from a late model Chevy HD3500. The guy wanted $15K for it and said he'd NEVER build another one. TOO many hours of fabrication. Enjoy. Rob

05-18-2010, 06:16 PM	#13
ghettoluxury Registered User Join Date: Apr 2009 Location: Waynesfield Ohio Posts: 1,991	Re: Project: ALTER-K-TION ('57 GMC Quad Cab) looks great, keep up the good work! __________________ 1949 Five Window, 1973 Step Side, 2000 Z71

05-21-2010, 12:23 AM	#14
addicted2dunes Insane In The Membrane Join Date: Jan 2010 Location: Orcutt, CA Posts: 446	Re: Project: ALTER-K-TION ('57 GMC Quad Cab) The Jeep is kicking my @$$. I thought it'd be a quick pull cage, finish welding cage, paint cage, patch rust in tub, Line-X tub, reinstall cage, reinstall interior..... Well the rust repair has taken me about a week. Started masking the tub to Line-X and it started to peel the paint, so now I have to repaint the passenger side of the Jeep. Hang tight folks, I'll be back on this project as quick as I can...... __________________ Cameron Gunlock Project: ALTER-K-TION ('57 GMC Quad Cab) http://67-72chevytrucks.com/vboard/s...d.php?t=393750

05-29-2010, 11:10 PM	#15
addicted2dunes Insane In The Membrane Join Date: Jan 2010 Location: Orcutt, CA Posts: 446	Re: Project: ALTER-K-TION ('57 GMC Quad Cab) Jeep is done! Back on this project starting on Mon., have to play at the local car show tomorrow, so one more day! Yeah, maybe I can get something accomplished! __________________ Cameron Gunlock Project: ALTER-K-TION ('57 GMC Quad Cab) http://67-72chevytrucks.com/vboard/s...d.php?t=393750

05-31-2010, 03:10 PM	#16
addicted2dunes Insane In The Membrane Join Date: Jan 2010 Location: Orcutt, CA Posts: 446	Re: Project: ALTER-K-TION ('57 GMC Quad Cab) A-pillar replaced, front cab back in (still have to cut out a lot more), and driver's door hung. __________________ Cameron Gunlock Project: ALTER-K-TION ('57 GMC Quad Cab) http://67-72chevytrucks.com/vboard/s...d.php?t=393750

05-31-2010, 04:55 PM	#17
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: Project: ALTER-K-TION ('57 GMC Quad Cab) nice progress! __________________ Looking for a 67-72 swb or blazer project in or around VA.

06-09-2010, 01:46 AM	#18
addicted2dunes Insane In The Membrane Join Date: Jan 2010 Location: Orcutt, CA Posts: 446	Re: Project: ALTER-K-TION ('57 GMC Quad Cab) And now we're on long term hold....... __________________ Cameron Gunlock Project: ALTER-K-TION ('57 GMC Quad Cab) http://67-72chevytrucks.com/vboard/s...d.php?t=393750



Register or Log In To remove these advertisements.

06-09-2010, 08:33 PM	#19
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,590	Re: Project: ALTER-K-TION ('57 GMC Quad Cab) Crap what happened??? __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

06-10-2010, 12:30 AM	#20
addicted2dunes Insane In The Membrane Join Date: Jan 2010 Location: Orcutt, CA Posts: 446	Re: Project: ALTER-K-TION ('57 GMC Quad Cab) Oh, nothing bad..... I guess I worded that a little rough, just finishing up other projects around the house and other vehicles. __________________ Cameron Gunlock Project: ALTER-K-TION ('57 GMC Quad Cab) http://67-72chevytrucks.com/vboard/s...d.php?t=393750

06-17-2010, 01:10 AM	#21
addicted2dunes Insane In The Membrane Join Date: Jan 2010 Location: Orcutt, CA Posts: 446	Re: Project: ALTER-K-TION ('57 GMC Quad Cab) Been working on this a little bit, nothing body wise though. My boss at the Streetrod shop I work at has been tediously banging out the dings and dents in all the trim to get it all ready for rechroming. __________________ Cameron Gunlock Project: ALTER-K-TION ('57 GMC Quad Cab) http://67-72chevytrucks.com/vboard/s...d.php?t=393750

06-21-2010, 02:07 AM	#22
addicted2dunes Insane In The Membrane Join Date: Jan 2010 Location: Orcutt, CA Posts: 446	Re: Project: ALTER-K-TION ('57 GMC Quad Cab) __________________ Cameron Gunlock Project: ALTER-K-TION ('57 GMC Quad Cab) http://67-72chevytrucks.com/vboard/s...d.php?t=393750

07-06-2010, 10:37 AM	#23
sak778 Registered User Join Date: Jun 2010 Location: Augusta, GA Posts: 2	Re: Project: ALTER-K-TION ('57 GMC Quad Cab) Where'd all the pic's go????

07-06-2010, 08:04 PM	#25
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,590	Re: Project: ALTER-K-TION ('57 GMC Quad Cab) lOOKS LIKE PHOTO BUCKET PROBLEMS.. __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

Register or Log In To remove these advertisements.