The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board > Squarebody Projects and Builds

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 02-05-2018, 01:58 PM   #26
chevy3100truck
Registered User
 
Join Date: Nov 2016
Location: Mission BC
Posts: 117
Re: #minijimmygmc Wifey's 1990 K5 Jimmy rebuild

Well, got the Off Road Design extended shock mounts for the front cut up & mounted in place. Ended up raising the mounting point for the new Bilstein 5125 shocks by 2 1/2" which should get the shocks close to the center of their travel at ride height and allow the axle to contact the bumpstop on the frame before bottoming out the shock.

Name:  IMG_4210.jpg
Views: 920
Size:  52.1 KB

Also installed the rear shock braces from ORD, well, just mocked them up and drilled the holes since the shocks need to get installed first, and I'm going to have to drop the rear axle again to correct the wheelbase & pinion angle, but need to have the engine back in the truck etc. first before I can do that.

Name:  IMG_4211.jpg
Views: 900
Size:  38.4 KB
__________________
@badgaragebc
chevy3100truck is offline   Reply With Quote
Old 02-05-2018, 02:04 PM   #27
chevy3100truck
Registered User
 
Join Date: Nov 2016
Location: Mission BC
Posts: 117
Re: #minijimmygmc Wifey's 1990 K5 Jimmy rebuild

So after getting the front shocks on (which was pretty much the last piece of the front end to be done for now) I figured I'd strip the trip off the sides of the Jimmy. Not sure what adhesive was used, but was 28 years old and still stuck very good lol.

Name:  IMG_4223.jpg
Views: 903
Size:  80.6 KB

The fun that trim can hide..... I won't be putting trim back on so this dent underneath the trim will have to get fixed. Have a bit of access from the rear, but if I can't straighten it enough I guess I'll just cut and replace the dented area.....

Name:  IMG_4224.jpg
Views: 885
Size:  59.9 KB

Lastly, decided to see how hard it'll be to strip the paint off. Just took a razor to the right side of this pic, couple minutes later and the primer was exposed. For the left side of the pic I used a bit of paint stripper and then scraped it off 10 minutes or so later. Might end up razoring a lot of the paint off and using the stripper for the primer, not sure. The stripped makes a massive mess though....

Name:  IMG_4227.jpg
Views: 887
Size:  36.5 KB
__________________
@badgaragebc
chevy3100truck is offline   Reply With Quote
Old 02-13-2018, 02:42 PM   #28
chevy3100truck
Registered User
 
Join Date: Nov 2016
Location: Mission BC
Posts: 117
Re: #minijimmygmc Wifey's 1990 K5 Jimmy rebuild

Spent a little more time this week on stripping paint. Just used a razor to get the topcoat off, the primer seems to sand off fairly easy with a DA, so not going to bother with paint stripper unless I need to.

About 3 hours total with a razor to get both sides to look about like this -

Name:  IMG_4237.jpg
Views: 770
Size:  55.7 KB

Since the top needed to be off for a while I figured I'd get it done & out of the way first. Started sanding off the old textured paint that GM had used on the fiberglass tops, it actually comes off much easier than I expected it too. The plan is to likely paint the top white both inside & out. Once it's painted I can get it out of the garage and tackle the bodywork on the Jimmy itself.

Name:  IMG_4269.jpg
Views: 805
Size:  41.2 KB
Name:  IMG_4271.jpg
Views: 764
Size:  36.5 KB

Also got around to sanding & painting the rad support. Just using good old Tremclad spray bomb on this like the engine bay so I won't be as pissed off at the inevitable scratches on it when I put everything back together lol. It's mostly re-assembled in this pic, just missing the headlight trim rings which are semi-gloss black.

Name:  IMG_4260.jpg
Views: 764
Size:  53.5 KB
__________________
@badgaragebc
chevy3100truck is offline   Reply With Quote
Old 02-27-2018, 12:28 AM   #29
chevy3100truck
Registered User
 
Join Date: Nov 2016
Location: Mission BC
Posts: 117
Re: #minijimmygmc Wifey's 1990 K5 Jimmy rebuild

well, lots of sanding later an 90% of the tub surface is now bare metal. Unfortunately the last 10% will probably take as much or more time than the first 90% lol.

At least there haven't been any hidden surprises yet, truck has never had a re-paint and hasn't had any real body damage other than what I already knew about (a dent in a crappy spot on the body line beside the fuel filler, a dent under the driver's side taillight, and two dents on the roof). The only other issues so far are a couple of small dings & dents and a broken spot weld on the drivers door.

Name:  IMG_4320.jpg
Views: 694
Size:  47.6 KB

Name:  IMG_4321.jpg
Views: 689
Size:  53.5 KB
__________________
@badgaragebc
chevy3100truck is offline   Reply With Quote
Old 04-05-2018, 05:59 PM   #30
chevy3100truck
Registered User
 
Join Date: Nov 2016
Location: Mission BC
Posts: 117
Re: #minijimmygmc Wifey's 1990 K5 Jimmy rebuild

Well, it's been a while since I've had a chance to post any updates.....

This was the dent that worried me the most on the body -
Name:  IMG_4340.jpg
Views: 648
Size:  59.4 KB

ended up with a bit of hammer & dolly work and a bit of heat I could get it 90% out. A bit of body filler and it'll be all good (this is just a daily driver after all). The photo seems to make it look worse than it is after straightening it a bit, the body line is back to being good, just needed a bit of filler below it.
Name:  IMG_4341.jpg
Views: 613
Size:  54.2 KB

broken spot welds on the drivers door - not really sure why this would have happened.
Name:  IMG_4346.jpg
Views: 641
Size:  24.5 KB

bit of welding & grinding and it's good to go
Name:  IMG_4347.jpg
Views: 650
Size:  29.4 KB
__________________
@badgaragebc
chevy3100truck is offline   Reply With Quote
Old 04-05-2018, 06:07 PM   #31
Dads79GMC
Registered User
 
Dads79GMC's Avatar
 
Join Date: Feb 2008
Location: Des Moines, Iowa
Posts: 1,237
Re: #minijimmygmc Wifey's 1990 K5 Jimmy rebuild

Great work on that dent!!
__________________
Instagram @HomeBuiltC10s

Dads 79 GMC Build Thread
http://67-72chevytrucks.com/vboard/s...d.php?t=642929

1978 Silverado Build
http://67-72chevytrucks.com/vboard/s...d.php?t=756016
Dads79GMC is offline   Reply With Quote
Old 04-05-2018, 06:07 PM   #32
chevy3100truck
Registered User
 
Join Date: Nov 2016
Location: Mission BC
Posts: 117
Re: #minijimmygmc Wifey's 1990 K5 Jimmy rebuild

After that it was time to weld up the trim holes around the back of the truck since I'm not putting the plastic body trim back on it. Only 3 holes on each side which was nice lol

Name:  IMG_4365.jpg
Views: 642
Size:  32.7 KB

Then, since the Jimmy isn't going to get the carpeted panels back on the doors, I welded up those holes as well. I might just leave them painted, or maybe will make something to cover them, haven't decided yet, but it's always easy to drill new holes if I put something there.

Name:  IMG_4363.jpg
Views: 641
Size:  38.9 KB
Name:  IMG_4370.jpg
Views: 635
Size:  39.8 KB
__________________
@badgaragebc
chevy3100truck is offline   Reply With Quote
Old 04-05-2018, 06:13 PM   #33
chevy3100truck
Registered User
 
Join Date: Nov 2016
Location: Mission BC
Posts: 117
Re: #minijimmygmc Wifey's 1990 K5 Jimmy rebuild

There was lot's more of little filling stuff in the body, but nothing serious, just little dents, parking lot dings, etc. Just the typical stuff for an old truck, with the exception of the lack of rust on the body.

Figured I'd try to fit the new fenders (the originals had been trimmed by a previous owner, so it gets re-pops)
Name:  IMG_4385.jpg
Views: 650
Size:  84.0 KB

Of course one of the brand new fenders has a dent in it..... And they've been sitting in my trailer for a few months, so it's not going back to the shop.

Name:  IMG_4380.jpg
Views: 643
Size:  30.2 KB

Luckily a bit of hammering got it pretty much straight and a skim coat of body filler got it exactly where it needed to be.
__________________
@badgaragebc
chevy3100truck is offline   Reply With Quote
Old 04-05-2018, 06:25 PM   #34
chevy3100truck
Registered User
 
Join Date: Nov 2016
Location: Mission BC
Posts: 117
Re: #minijimmygmc Wifey's 1990 K5 Jimmy rebuild

got my assistant to help with sanding the hood down to bare metal. The hood was mint (other than horrible paint) prior to getting knocked over when it was leaned against the back of my garage...... only had a couple of dings from the issue, one on the front edge the other on the body line down the center. Luckily both were accessible from the backside of the hood as they were right at cutouts in the bracing.

Name:  IMG_4394.jpg
Views: 622
Size:  62.6 KB
Name:  IMG_4395.jpg
Views: 623
Size:  47.6 KB

Stripped the tailgate down to bare metal, again, just some typical damage near the top of the tailgate. Hammered out & a skim coat of filler ended up fixing it. I couldn't believe the rear window still worked though, the window channels inside the tailgate were basically non existent, they were only being held together by the felt liners lol.

Name:  IMG_4414.jpg
Views: 627
Size:  43.3 KB

Cowl panel - what a pain in the ass...... I wasn't going to sand this down to bare metal since the louvers are such a pain, but I couldn't leave it, so bare metal it goes...... I'm not sure how many hours it took, but it was way too many!
Name:  IMG_4413.jpg
Views: 622
Size:  46.7 KB

And the canopy - it'd been a while since I sanded the majority of it down to get rid of the factory textured paint. I had chipped out everything from the seams on it since it was loose anyhow, I figured I'd try just filling the seams completely with Everglas, hopefully that doesn't come back to bite me, but I've got another canopy and I was thinking of cleaning it up and painting it too (a different colour that this one will be). If the Everglas cracks at least I'll be able to get something else done and just swap them. Lots of little pinholes in the factory fiberglass, and lousy alignment between the two halves, I can see why GM went to using textured paint, hides it all so the quality can be crappy. What I am not doing is getting the top totally flat. It's now smooth, but the fiberglass top has waves to it where the bracing is inside and for something you can't see (it'll be about 7'3" or so off the ground), I'm not going to fix it.

Name:  IMG_4399.jpg
Views: 618
Size:  55.1 KB
__________________
@badgaragebc
chevy3100truck is offline   Reply With Quote
Old 04-05-2018, 06:28 PM   #35
chevy3100truck
Registered User
 
Join Date: Nov 2016
Location: Mission BC
Posts: 117
Re: #minijimmygmc Wifey's 1990 K5 Jimmy rebuild

so since it is getting closer to paint, I decided to make a list of things that still needed completing......
Name:  IMG_4420.jpg
Views: 619
Size:  43.1 KB

I shouldn't have done that lol
__________________
@badgaragebc
chevy3100truck is offline   Reply With Quote
Old 04-05-2018, 06:37 PM   #36
chevy3100truck
Registered User
 
Join Date: Nov 2016
Location: Mission BC
Posts: 117
Re: #minijimmygmc Wifey's 1990 K5 Jimmy rebuild

I decided to paint a few parts separately since a. I don't have a paint booth and b. it'll make it easier as I'm kind of space limited (and for obvious reasons I can't put any of this stuff outside in the pacific northwest this time of year). Good excuse to try out my new 3M Accuspray gun. Have to say I'm happy with it so far - the disposable liners & the changeable tips that take just a couple seconds to clean are awesome.

Hood, tailgate and some dash pieces I decided to paint separate from the truck.
Name:  IMG_4422.jpg
Views: 626
Size:  47.9 KB

2 coats of epoxy primer, then 2 coats of primer surfacer.
Unfortunately I had a fubar with the cowl panel during this (stupid mistake lol), so it got to get sanded down again later.....
Name:  IMG_4426.jpg
Views: 624
Size:  39.1 KB

After the two coats of primer surfacer, it was time to wetsand the primer with 400 grit...... whenever you think you're done, wipe it down and start again lol

Name:  IMG_4427.jpg
Views: 619
Size:  18.5 KB

Hood after sanding -
Name:  IMG_4429.jpg
Views: 619
Size:  33.5 KB
__________________
@badgaragebc
chevy3100truck is offline   Reply With Quote
Old 04-05-2018, 06:45 PM   #37
chevy3100truck
Registered User
 
Join Date: Nov 2016
Location: Mission BC
Posts: 117
Re: #minijimmygmc Wifey's 1990 K5 Jimmy rebuild

So for paint, my wife had decided on a gunmetal grey metallic colour. Nice and easy for a novice to paint lol. I'm obviously more than a bit worried about tiger striping etc, but hopefully the combination of laying down 3 coats (one across, one 45 degrees to that, and one 45 degrees to the original + a drop coat) will keep it all nice and even.

Name:  IMG_4436.jpg
Views: 620
Size:  31.5 KB

glovebox door
Name:  IMG_4438.jpg
Views: 622
Size:  36.5 KB

hood under lights -
Name:  IMG_4439.jpg
Views: 625
Size:  36.5 KB

and lastly - the day after painting it, taking the hood out in the sunshine to make sure that it doesn't have any tiger stripes (after staring at it for about an hour and a half thinking it did lol). Came out pretty decent, there are a few little flaws with dust, but I think sanding and polishing the clearcoat will get rid of everything that was there.

Name:  IMG_4441.jpg
Views: 614
Size:  39.7 KB
__________________
@badgaragebc
chevy3100truck is offline   Reply With Quote
Old 04-05-2018, 06:51 PM   #38
chevy3100truck
Registered User
 
Join Date: Nov 2016
Location: Mission BC
Posts: 117
Re: #minijimmygmc Wifey's 1990 K5 Jimmy rebuild

and to get up to date, the latest would be painting a couple of more pieces last night. The re-painted cowl panel, and the outside of the tailgate. I know the tailgate should be painted while vertical to keep the metallics in the same orientation, but I'm going to take my chances that it won't be too obvious when installed as it will be beside the tail lights and only the top part of the tailgate posts. Hope that doesn't bite me in the ass later.

Name:  IMG_4453.jpg
Views: 617
Size:  43.5 KB
Name:  IMG_4454.jpg
Views: 615
Size:  45.7 KB
Name:  IMG_4455.jpg
Views: 614
Size:  50.7 KB

I'm hoping to get the canopy painted this weekend if all goes well. That isn't going to be body colour and needs both the inside & outside painted, so hopefully I can wrangle a neighbour over to help lift it around lol. I still can't believe how heavy that thing is compared to canopies I've had on various trucks over the years.
__________________
@badgaragebc
chevy3100truck is offline   Reply With Quote
Old 04-07-2018, 02:00 AM   #39
Jaysonb
Registered User
 
Jaysonb's Avatar
 
Join Date: May 2009
Location: Good Thunder Mn.
Posts: 955
Re: #minijimmygmc Wifey's 1990 K5 Jimmy rebuild

Looks great!
Jaysonb is offline   Reply With Quote
Old 04-07-2018, 11:57 AM   #40
SBTork
Garage wrench
 
SBTork's Avatar
 
Join Date: Feb 2008
Location: LaCrosse, WI
Posts: 1,856
Re: #minijimmygmc Wifey's 1990 K5 Jimmy rebuild

Quote:
Originally Posted by Jaysonb View Post
Looks great!
Ditto! Looking very good, nice project!
__________________
-Adam


90 V1500 GMC Suburban 350/700R4/NP241.....
01 Saturn SL1 stock DD.....
SBTork is offline   Reply With Quote
Old 04-08-2018, 02:51 AM   #41
chevy3100truck
Registered User
 
Join Date: Nov 2016
Location: Mission BC
Posts: 117
Re: #minijimmygmc Wifey's 1990 K5 Jimmy rebuild

Thanks. I've never tackled a project with this sort of scope before. Just trying not to screw too much up lol
Posted via Mobile Device
chevy3100truck is offline   Reply With Quote
Old 04-08-2018, 06:45 PM   #42
Whamo
Registered User
 
Whamo's Avatar
 
Join Date: Mar 2014
Location: Nap Town, Indianapolis
Posts: 233
Re: #minijimmygmc Wifey's 1990 K5 Jimmy rebuild

You are rockin this build!
__________________
Just a Hillbilly in the Hood

http://67-72chevytrucks.com/vboard/s...d.php?t=622194
Whamo is offline   Reply With Quote
Old 04-15-2018, 08:34 PM   #43
LT7A
Registered User
 
Join Date: Oct 2015
Location: PNW
Posts: 3,472
Re: #minijimmygmc Wifey's 1990 K5 Jimmy rebuild

A lot of work done in a short amount of time. And it looks great. You keep saying it's a driver, and I realize that you're not building it for show, but I wonder if your wife realizes just how high of a quality level you're building to. Obvious to us though, so keep on. Thanks for sharing.
LT7A is offline   Reply With Quote
Old 05-08-2018, 10:02 PM   #44
chevy3100truck
Registered User
 
Join Date: Nov 2016
Location: Mission BC
Posts: 117
Re: #minijimmygmc Wifey's 1990 K5 Jimmy rebuild

Thanks for the compliments!

I've been working on it as much as I can since I last posted, the top is now painted inside & out

Inside before -

Name:  IMG_4466.jpg
Views: 435
Size:  39.7 KB

Scuff & Spray - I left the texture on the inside, which unfortunately meant leaving some of the cracks along the edges since I couldn't figure out a good way to fix them and keep the texture (they're just cracks in the original coating where the parts are joined together)

after - well - it's still white, but it's clean looking and coated with a satin clear coat
Name:  IMG_4467.jpg
Views: 440
Size:  32.1 KB

For the outside I smoothed the factory seams with fiberglass and sprayed a black with a satin clear coat. Not perfect - I'd never sprayed satin before, so I'll probably end up redoing it at some point, but unless you're 7' tall you can't see the top of the roof anyhow.

Name:  IMG_4482.jpg
Views: 429
Size:  38.9 KB
Name:  IMG_4481.jpg
Views: 430
Size:  45.9 KB

Basically the problem was because I had it supported too high and couldn't easily reach the middle section of the roof to get a consistent pass on the clear coat. The satin clear needs to be applied very consistently to get an even finish, so in the very center of the roof there are a couple of stipes where the gloss doesn't exactly match.
__________________
@badgaragebc
chevy3100truck is offline   Reply With Quote
Old 05-08-2018, 10:14 PM   #45
Palf70Step
State of Confusion!

 
Palf70Step's Avatar
 
Join Date: Jul 2002
Location: Gulfport, MS USA
Posts: 46,575
Re: #minijimmygmc Wifey's 1990 K5 Jimmy rebuild

That top is really nice!
__________________
Bill
1970 Chevy Custom/10 LWB Fleetside
2010 Toyota Tacoma PreRunner SR5 Double Cab - DD

Member of Louisiana Classic Truck Club (LCTC)

Bill's Gallery
Life isn't tied with a bow, but it's still a gift.
Live simply. Love generously. Care deeply. Speak kindly. Leave the rest to God!
Palf70Step is offline   Reply With Quote
Old 05-08-2018, 10:42 PM   #46
chevy3100truck
Registered User
 
Join Date: Nov 2016
Location: Mission BC
Posts: 117
Re: #minijimmygmc Wifey's 1990 K5 Jimmy rebuild

Next up was the dash -
I didn't sand the dash down to bare metal as the original paint was all still sticking well. Basically sanded it with 180 grit, shot 2 coats of epoxy, 2 coats of primer surfacer, quick sand, then the colour & clear

Name:  IMG_4497.jpg
Views: 431
Size:  48.5 KB

and after the colour and clear - all the other parts were painted separately previously (glove box, ashtray, filler below column) Not the best way to do it, but easier to get it done this way and get all the edges etc.

Name:  IMG_4499.jpg
Views: 421
Size:  42.9 KB
__________________
@badgaragebc
chevy3100truck is offline   Reply With Quote
Old 05-08-2018, 10:45 PM   #47
chevy3100truck
Registered User
 
Join Date: Nov 2016
Location: Mission BC
Posts: 117
Re: #minijimmygmc Wifey's 1990 K5 Jimmy rebuild

primering the door sills & inside of the doors was next, these areas were mostly sanded down to bare metal, just the inner parts of the door that will be covered with the door panels weren't taken to bare metal. I filled all of the holes for the lower carpet panel as the plan right now is to leave them painted, not covered (I can always put a cover on them later if we want too, but it'd be hard to fill the screw holes and paint them if we wanted to ditch the panels later on)

Name:  IMG_4508.jpg
Views: 430
Size:  43.5 KB
__________________
@badgaragebc
chevy3100truck is offline   Reply With Quote
Old 05-08-2018, 10:53 PM   #48
chevy3100truck
Registered User
 
Join Date: Nov 2016
Location: Mission BC
Posts: 117
Re: #minijimmygmc Wifey's 1990 K5 Jimmy rebuild

After some final sanding to clean up the bare metal tub as well as remove the overspray from spraying the door sills it was finally primer time.

Name:  IMG_4517.jpg
Views: 427
Size:  50.4 KB

A couple coats of epoxy primer, then a bit more body work, then 3 coats of primer surfacer -

Name:  IMG_4532.jpg
Views: 423
Size:  46.6 KB
Name:  IMG_4534.jpg
Views: 422
Size:  52.1 KB

Also got around to spraying primer down on the new front fenders -

Name:  IMG_4547.jpg
Views: 424
Size:  60.9 KB
__________________
@badgaragebc
chevy3100truck is offline   Reply With Quote
Old 05-08-2018, 10:57 PM   #49
chevy3100truck
Registered User
 
Join Date: Nov 2016
Location: Mission BC
Posts: 117
Re: #minijimmygmc Wifey's 1990 K5 Jimmy rebuild

and to get up to date, I sprayed the colour and clear on the door jambs and inside of the doors.

Name:  IMG_4558.jpg
Views: 427
Size:  46.8 KB
Name:  IMG_4559.jpg
Views: 420
Size:  40.3 KB
Name:  IMG_4560.jpg
Views: 415
Size:  34.3 KB

I'm hoping to get the body completely painted by the end of May so I can start reassembly, but there is a lot of sanding left to do on the primer before it'll be ready for colour and clear. It's just a driver, so it doesn't have to be perfect, but trying to get it as good as I can.
__________________
@badgaragebc
chevy3100truck is offline   Reply With Quote
Old 05-09-2018, 08:30 AM   #50
Greenlee
Registered User
 
Greenlee's Avatar
 
Join Date: Jun 2004
Location: El Lago, TX
Posts: 1,668
Re: #minijimmygmc Wifey's 1990 K5 Jimmy rebuild

Nice build! You have done a great job on this thing. It’s going to turn out nice!
Greenlee is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:30 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com