dana 44 parts interchangeable? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

cheyenne10 · 01-27-2004, 01:46 AM

Can we use ring and pinions or carriers out of ford dana 44's in our housings?
(i.e. 3.50 gears)

**JIMs70GMC** · 01-27-2004, 08:01 AM

I don't think so the dana 44's in fords are high pinion axles. Assuming you mean the front axle as most fords had the 8 or 9" rear end.

cheyenne10 · 01-27-2004, 03:06 PM

Jeeps, dodges, fords, chevys, etc used dana 44 fronts during same time period.

I assume there are different widths but are many parts interchangeable?

**kwmech** · 01-29-2004, 11:59 AM

All 44 parts are interchangable except ford front gears as they are reverse cut, and the early jeeps that were coarse spline spiders. I think there are 3.54 standard cut gears available-- wagoneer if I remember right

leadfoot067 · 01-31-2004, 11:47 PM

ya many waggoneers have the 3.54s...and a standard pinion..

01-27-2004, 01:46 AM	#1
cheyenne10 Senior Member Join Date: Apr 2000 Location: Oregon Posts: 2,511	dana 44 parts interchangeable? Can we use ring and pinions or carriers out of ford dana 44's in our housings? (i.e. 3.50 gears) __________________ Bob

01-27-2004, 08:01 AM	#2
JIMs70GMC user # 2756 Join Date: Jun 2001 Location: Chesapeake, Virginia Posts: 4,612	I don't think so the dana 44's in fords are high pinion axles. Assuming you mean the front axle as most fords had the 8 or 9" rear end. __________________ 1970 K25, 8' stepside bed 350/465/205 44 up front, 60 in the rear 4.10s rolling on 33" Dunlop MTs 1986 K5, 350/465/208 Dana 60/14 bolt from a cucv 36" Super Swampers TSL/SX 1983 K20 w/ CUCV axles, 350/700R4/208 sitting on 37" Goodyears 1986 M1031 6.2 diesel, TH400/NP205 locker in the rear and a LS in the front, all stock for now..... 1986 K30, 350/400/205 dana 60 and 14 bolt. I kept the drivetrain. Body/bad and chassis are gone. 1981 K30, 350/465/205 dana 60 and dually 14 bolt. Has a G80, and a flat bed. Going to replace the flat bed. 1985 K20, 350/400/208 10 bolt and SF 14 bolt. I wonder where I can find some 1 tons. Hmmmmm

01-27-2004, 03:06 PM	#3
cheyenne10 Senior Member Join Date: Apr 2000 Location: Oregon Posts: 2,511	yes talking front ends Jeeps, dodges, fords, chevys, etc used dana 44 fronts during same time period. I assume there are different widths but are many parts interchangeable? __________________ Bob

01-31-2004, 11:47 PM	#5
leadfoot067 horsepower junkie Join Date: Aug 2003 Location: graham, washington Posts: 326	ya many waggoneers have the 3.54s...and a standard pinion.. __________________ 67 short wide box,350/700r4/3.73posi 71 olds cutlass "S" mom bought new..12.30s@113MPH

01-29-2004, 11:59 AM	#4
kwmech Senior Member Join Date: Mar 2003 Location: Colfax-California Posts: 8,393	All 44 parts are interchangable except ford front gears as they are reverse cut, and the early jeeps that were coarse spline spiders. I think there are 3.54 standard cut gears available-- wagoneer if I remember right



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.