|
10-22-2016, 12:28 AM
|
#1 |
|
Registered User
Join Date: Oct 2016
Location: Daly city california
Posts: 4
|
Will this setup work
Hello im looking to put a 350 sbc with a t56 tranny in a 68 lb c10
What problems would i run into if i went with this setup? Im still new to this so dont be mean if the question sounds stupid. Thanks. Right now it has a 307 and powerglide in it. I just wanna know if the setup i want will work and if it does what parts should i look out for when buying the tranny Posted via Mobile Device |
|
|
|
10-22-2016, 02:51 AM
|
#2 |
|
Post Whore
  
Join Date: May 2015
Location: Alabama
Posts: 14,579
|
Re: Will this setup work
Try posting this in the 67-72 board section
|
|
|
|
10-22-2016, 07:25 AM
|
#3 |
|
State of Confusion!
 
Join Date: Jul 2002
Location: Gulfport, MS USA
Posts: 46,611
|
Re: Will this setup work
Moved your post for you. I keep thinking about the same idea, but for my 64. It will be interesting to see the responses.
__________________
Bill 1970 Chevy Custom/10 LWB Fleetside 2010 Toyota Tacoma PreRunner SR5 Double Cab - DD Member of Louisiana Classic Truck Club (LCTC) Bill's Gallery Life isn't tied with a bow, but it's still a gift. Live simply. Love generously. Care deeply. Speak kindly. Leave the rest to God! |
|
|
|
|
10-22-2016, 08:02 AM
|
#4 |
|
Registered User
Join Date: Jun 2010
Location: Orlando, Florida
Posts: 2,506
|
Re: Will this setup work
I think the T56 uses a hydraulic clutch system. That might take some figuring.
__________________
71 Chevy C10 Shortbed Stepside. LT1 with 4l60E. Just got back from painter, in assembly now. |
|
|
|
|
10-22-2016, 08:10 AM
|
#5 |
|
Senior Member
Join Date: Dec 2013
Location: Gods country East,Tn
Posts: 8,545
|
Re: Will this setup work
Yes , Guys have already done it , Get out your wallet .
Just to start ... bell housing clutch,pressure plate ,throw out bearing ,pilot bearing shifter clutch pedal and complete linkage trans mount drive shaft and yoke floor shift steering column manual flywheel correct starter speedometer correction I'm not sure if you need the high hump for clearance ,This short list will get you started . search the forum for instructions and do your homework before ripping into it . with all the parts sitting on the floor its a weekend job .  https://shiftsst.com/
__________________
 1967 Factory short bed - Old school '71 - 350 / 4bolt / 487 heads / Edelbrock C3BX Muncie M-22 4 speed / Hurst Comp plus Factory 12 bolt posi 3.73 / 255-70-15 Smoothed firewall / Factory cowl induction Power disc brakes / power steering / 3.5-5" drop |
|
|
|
|
10-22-2016, 10:19 AM
|
#6 |
|
Registered User
Join Date: Sep 2016
Location: Vancouver BC
Posts: 784
|
Re: Will this setup work
Personally, I'd be looking for a parts donor vehicle, one that was a manual trans, floor shift truck to begin with. That way, you might luck into a lot of the parts, and possibly be able to sell what you don't need to help pay for the project.
__________________
Rick -69 GMC 910 Long Box, 350 -98 Chev Silverado 1500, 350 Vortec 4L60e -08 Mustang GT Convertible |
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
