The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Engine & Drivetrain

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 11-07-2017, 01:54 AM   #1
Ryan Hubbard
Senior Member
 
Join Date: Aug 2007
Location: Mission Viejo, CA
Posts: 204
Holley Terminator EFI Install

I installed the Holley Terminator TBI EFI system in my 71 C20 pickup a couple weeks ago. I also have it controlling my 4L80E transmission. Here is the spec for my truck:

Engine
350 4 bolt main bored .030 over
Edelbrock Performer RPM Heads
8.5:1 CR
Manguson Eaton Rotor Supercharger (12 PSI Pulleys)

Transmission:
4L80E

Rear Axle:
Dana 60 with 3.55 gears and Detroit Locker

The install went pretty well, I had a TCI transmission controller installed in the truck so I just reused the hole in the fire wall for the Terminator wiring and mounted the computer on the glove box door. ( I have a billet aluminum glove box door) I also used the Holley Fuel pump kit with the filters, fuel line and fittings.

I also installed a small cap HEI electronic distributor so that the Terminator system could control the timing for the engine. I am still using my MSD 6AL ignition box too.

Since I am running a roots blower, I had to change out the MAP sensor to one that referenced the manifold vacuum/pressure after the blower. I just cut the plug of the wiring harness and connected a new plug and some longer wires and told the ecu that I had a 3 bar Map sensor.

Once I got the system installed, I followed the instructions and was able to set the initial timing and got the engine started and running. Once I got the engine running it took a little "tweeking" to get everything dialed in.

After the initial starts and tweeking, I started driving the truck and noticed a big improvement in drivability. I have now put over 1000 miles on the truck with this system on it and towed my other 71 K20 pickup over 600 miles and was able to get 9 mpg towing while still maintaining 75-80 mph on the interstate. (Before anyone says anything, my truck has 4 wheel disk brakes and trailer brakes and I was following the posted speed limits). I had done a lot of work on the carb for this truck and it was a well tuned carb but still not as nice as this system. I am driving another 700 miles tomorrow without the trailer or truck and I will see how that drive goes. But I was getting around 13.5 mpg with out the trailer. I am going to tweek the tune a little on the trip tomorrow and see if I can get a little better mpg. Not bad for a truck that has 550 Hp and over 500 LbFt of torque.
Ryan Hubbard is offline   Reply With Quote
Old 11-08-2017, 08:26 PM   #2
Husker
Senior Member
 
Husker's Avatar
 
Join Date: Dec 1999
Location: Mid NE USA
Posts: 1,785
Re: Holley Terminator EFI Install

I want to Try one of these Kits on my Jeep CJ5 304 v8
Ron
__________________
Member #111
68 C-10 Daily Driver
70 4x4 Project
76 Jeep CJ-5

Help Support the Board:

http://67-72chevytrucks.com/vboard/payments.php


He who knows nothing is closer to the truth than he whose mind is filled with falsehoods and errors.
Thomas Jefferson
Husker is offline   Reply With Quote
Old 11-10-2017, 11:02 PM   #3
YoungPup1977
Registered User
 
Join Date: Jun 2015
Location: ()
Posts: 143
Re: Holley Terminator EFI Install

so I was wondering, the cost of this unit worth it ? if cost was a factor....
__________________
()
YoungPup1977 is offline   Reply With Quote
Old 11-11-2017, 12:48 PM   #4
B. W.
Senior Member
 
B. W.'s Avatar
 
Join Date: Nov 2014
Location: Bigfork, Montana
Posts: 599
Re: Holley Terminator EFI Install

Hey, would you mind posting some pics? I am thinking about a similar setup.
B. W. is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:17 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Copyright 1997-2013 67-72chevytrucks.com