|
12-28-2014, 10:41 AM
|
#1 |
|
Registered User
Join Date: May 2014
Location: Halifax
Posts: 21
|
how low can you go?
Just wondering how low can you go without bags ? Would like to get as low as possible without bags, but if I have too I will go the bag route.
|
|
|
|
12-28-2014, 11:28 AM
|
#2 |
|
Registered User
Join Date: Dec 2012
Location: Temple City
Posts: 3,560
|
Re: how low can you go?
A 5-7 is the lowest bolt on drop.
With a grinding wheel, a torch, and little to no common sense you can go 1 inch off the ground before pebbles are major obstacles. |
|
|
|
|
12-28-2014, 11:51 AM
|
#3 |
|
Registered User
Join Date: May 2014
Location: Halifax
Posts: 21
|
Re: how low can you go?
Well thats what im after 1inch off the ground .
|
|
|
|
|
12-28-2014, 12:26 PM
|
#4 |
|
Registered User
Join Date: Sep 2007
Location: Wichita Falls, Texas
Posts: 459
|
Re: how low can you go?
The control arms 1" off the ground isn't the best idea. Not really that safe either. If you want ground dragging low build for ground dragging low, you'll be happier in the long run.
|
|
|
|
|
12-28-2014, 06:08 PM
|
#5 | |
|
Registered User
Join Date: Mar 2013
Location: SF
Posts: 345
|
Re: how low can you go?
Quote:
|
|
|
|
|
|
12-28-2014, 06:12 PM
|
#6 |
|
Registered User
Join Date: May 2014
Location: Halifax
Posts: 21
|
Re: how low can you go?
Ok I want it to be safe
|
|
|
|
|
12-28-2014, 06:42 PM
|
#7 |
|
Registered User
Join Date: Jul 2009
Location: San Jose Ca
Posts: 2,871
|
Re: how low can you go?
You could go 6/8 with taller tires but then you will need to modify your inner fenders, notch the frame etc.
You can run an aftermarket crossmember and be lower with coil overs. You could also do a minor Z in the front and go lower on a stock set up. You can do a 5/7 or 6/8 static drop and do a traditional body drop for a few more inches. It all depends on how much work you want to do...
__________________
David Used parts build: http://67-72chevytrucks.com/vboard/s...d.php?t=638991 My brother's Nova: http://www.67-72chevytrucks.com/vboa...d.php?t=727985 Rear suspension rework: http://www.67-72chevytrucks.com/vboa...d.php?t=750557 Instagram: myfabguy |
|
|
|
|
12-28-2014, 06:48 PM
|
#8 |
|
Registered User
Join Date: May 2014
Location: Halifax
Posts: 21
|
Re: how low can you go?
I have been thinking of the 6/8 drop and a body drop
|
|
|
|
|
12-28-2014, 07:12 PM
|
#9 |
|
Truck junkie
 
Join Date: May 2006
Location: Reno NV
Posts: 697
|
Re: how low can you go?
When I was about 19 I had a toyota that was static dropped about 1" off the pavement. I hit a manhole cover going about 30mph that was sticking up at one edge. It stopped the truck and bent the frame. Bags are a way better and safer alternative.
|
|
|
|
|
12-28-2014, 11:37 PM
|
#10 | |
|
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 21,910
|
Re: how low can you go?
Quote:
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. |
|
|
|
|
|
12-29-2014, 08:30 AM
|
#11 |
|
Registered User
Join Date: May 2010
Location: Broken Arrow Okla.
Posts: 510
|
Re: how low can you go?
I have about a 5.5/7 6/8 drop. 2 inch lowered CPP Moudular spindles with 2inch lowered springs with about half a coil cut off and Porterbuilt rear trailing arms with 3inch drop built in and 4inch lowered springs and a c-notch. I know 4 + 3=7 on the rear but after it was all said and done it was 8 inches lower. Rides good no rubbing expect on the front if you hit a big big dip, I have a big block if it were a small block don't think it would ever happen.
__________________
1967 swb 454 cid 700R4 trans SOLD 2006 Chevy Trailblazer SS 2013 Camaro RS convertible the wife's Build thread http://67-72chevytrucks.com/vboard/s...d.php?t=573248 |
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
