Need help wiring ignition switch-photos - The 1947 - Present Chevrolet & GMC Truck Message Board Network

RaceAGMC · 06-17-2012, 06:56 PM

I am just about finished up doing my 6.0 swap in my 1970 C-10. I am in need of help wiring up the ignition switch. I have attached a picture of the back side of the switch an of the wires I am working with along with their labels. Any help to get it going would be great.

Wires
Pink-IGN Empty
Yellow with black stripe-cranking signal
Orange-battery empty
Pink with black stripe-12V switched
Black-ground

If someone could tell me which wires go where on the switch that would help me a lot.

Posted via Mobile Device
Posted via Mobile Device

ls1nova71 · 06-17-2012, 07:37 PM

Do you have the rest of the factory harness? Or are you trying to wire from scratch? Or are you trying to hook the original switch to an aftermarket harness?
Posted via Mobile Device

RaceAGMC · 06-17-2012, 07:53 PM

This is a reworked factory harness. Everything I the engine compartment is hooked up. All that is left is hooking up the battery and ignition switch.
Posted via Mobile Device

ls1nova71 · 06-17-2012, 10:32 PM

So you're just hooking up the 6.0 harness? If that's the case, just hook the ignition relay power to the wire that originally went to the distributor and the battery power to a constant power source.
Posted via Mobile Device

06-17-2012, 06:56 PM	#1
RaceAGMC Registered User Join Date: Jul 2007 Location: Charlotte, NC Posts: 350	Need help wiring ignition switch-photos I am just about finished up doing my 6.0 swap in my 1970 C-10. I am in need of help wiring up the ignition switch. I have attached a picture of the back side of the switch an of the wires I am working with along with their labels. Any help to get it going would be great. Wires Pink-IGN Empty Yellow with black stripe-cranking signal Orange-battery empty Pink with black stripe-12V switched Black-ground If someone could tell me which wires go where on the switch that would help me a lot. Posted via Mobile Device Posted via Mobile Device __________________ 70 CST, 6.0/ 4L80E in the works. Custom harness by 68 Short Step

06-17-2012, 07:37 PM	#2
ls1nova71 Registered User Join Date: Dec 2009 Location: Independence Mo Posts: 4,118	Re: Need help wiring ignition switch-photos Do you have the rest of the factory harness? Or are you trying to wire from scratch? Or are you trying to hook the original switch to an aftermarket harness? Posted via Mobile Device __________________ My '72 short bed build. http://www.ls1tech.com/forums/conver...6-0-4l80e.html 5.3 swap into my RUSTY '71 C10 http://ls1tech.com/forums/conversion...71-c-10-a.html

06-17-2012, 07:53 PM	#3
RaceAGMC Registered User Join Date: Jul 2007 Location: Charlotte, NC Posts: 350	Re: Need help wiring ignition switch-photos This is a reworked factory harness. Everything I the engine compartment is hooked up. All that is left is hooking up the battery and ignition switch. Posted via Mobile Device __________________ 70 CST, 6.0/ 4L80E in the works. Custom harness by 68 Short Step

06-17-2012, 10:32 PM	#4
ls1nova71 Registered User Join Date: Dec 2009 Location: Independence Mo Posts: 4,118	Re: Need help wiring ignition switch-photos So you're just hooking up the 6.0 harness? If that's the case, just hook the ignition relay power to the wire that originally went to the distributor and the battery power to a constant power source. Posted via Mobile Device __________________ My '72 short bed build. http://www.ls1tech.com/forums/conver...6-0-4l80e.html 5.3 swap into my RUSTY '71 C10 http://ls1tech.com/forums/conversion...71-c-10-a.html



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.