The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Suspension

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 12-29-2008, 01:40 AM   #1
nuke1
Registered User
 
nuke1's Avatar
 
Join Date: Jun 2007
Location: Saskatoon, Saskatchewan,:
Posts: 2,901
Adjustable rear trailing arms how-to

ADJUSTABLE REAR TRAILING ARMS HOW-TO
MODS move if needed

I thought i would give a how-to on this. everyone on here has been very inspirational and helping of others. so here is something from me. I wanted to build adjustable trailing arms for a few reasons. i can alter the wheelbase, alignment is easier, and i added ballistic joints that are teflon lined for uninhibited wheel travel in the rear, there is no compression of a bushing. Well on to the build, if there are questions ask away, i will answer to the best of my knowledge, and please forgive me if i made a mistake.

Anyways, the first thing i did was lay down some white poster board on my bench, i taped it down so it would not move. I then traced out the original trailing arm for the angle and pivot points. once i did this i marked out my tubing i was using (2"x3"x3/16") and found where my new angle will be located.
Name:  IMG_5393 (Small).JPG
Views: 24284
Size:  45.5 KB
Once i marked out what and where my new trailing arms would be i proceeded to find the existing angle of the old trailing arms. i then used this angle to determine the pie cut i would need to kick up the rear of the arms. Sorry i did not show a pic of the angle finder.
Name:  IMG_5394 (Small).JPG
Views: 18884
Size:  45.6 KB
What i did now was to take a rachet tie down and squish the two ends together until my desried anlgle was acheived. Once it was acheived i then tack welded in two spots on the top of the cut so it did not move, do not fully weld up yet. and make sure that the arm is still square.
Name:  IMG_5395 (Small).JPG
Views: 20531
Size:  55.4 KB
i then cut the other arm with the same pie cut. once that is done i used the tie down againg to bring that one together, once it is i used C-clamps to clamp them together to make sure that they were the same angle. once this was done i tack welded the outsides of the arms. Then i removed the clamps and tack welded the inside of the arms, all the while making sure they are straight. once this is done i fully welded them up. at the same time, i made a boxing plate for the end of the arm and welded it in too.
Name:  IMG_5397 (Small).JPG
Views: 18476
Size:  55.7 KB
Name:  IMG_5398 (Small).JPG
Views: 20669
Size:  34.2 KB
__________________
James
1968 GMC "HAVOC"
1986 GMC "Frank"
J.J.R.H. Design & Consulting

My 68`Rebuild "HAVOC": http://67-72chevytrucks.com/vboard/s...d.php?t=316300
A 58' chev build thread: http://www.67-72chevytrucks.com/vboa...d.php?t=311238
1969 Camaro Pro Touring http://67-72chevytrucks.com/vboard/s...61#post3513361
Swiss Cheese: http://67-72chevytrucks.com/vboard/s...d.php?t=384390
Adjustable Trailing Arm How-To: http://67-72chevytrucks.com/vboard/s...d.php?t=321100
1968 Ford Farm Truck: http://67-72chevytrucks.com/vboard/s...=1#post6555587
nuke1 is offline   Reply With Quote
Old 12-29-2008, 01:55 AM   #2
nuke1
Registered User
 
nuke1's Avatar
 
Join Date: Jun 2007
Location: Saskatoon, Saskatchewan,:
Posts: 2,901
Re: Adjustable rear trailing arms how-to

Well, i had that end of the arms done for now so on to the other end, because i was using flex joints, i got some DOM tubing threaded to accept my joints, the threads are 1 1/4". the sleeves are 5 inches long. on the end of the sleeves i attached some square solid stock in a cross fashin, this was then welded up to the DOM tubing. i made a plate for the other end of the tubing as well, i cut a hole in it with a hole saw and my drill press. i proceeded to insert the section now into the arm. i drilled four holes in the arm that equates to where the solid stock will be. i left the end of the DOM tubing sticking out 3/16" for welding. i also welded the backside of it, but make sure that you get it square.
Name:  IMG_5400 (Small).JPG
Views: 19618
Size:  50.2 KB
Here it is welded up.
Name:  IMG_5402 (Small).JPG
Views: 18085
Size:  50.4 KB
Now back to the other end. I now needed some extra strength for where the springs and rearend sit. so i cut 2 pieces 3" by 17" in lenght. i then used C- clamps to hold these in place and bend them as needed. they are centered and fully welded all the way around. now all that is left is to drill the holes for the rear differential and spring. the spring hole i am gonna drill a hole on just the top and insert a bushing with threads in it that will be welded to the arm, for the bolt to attach through the top.
Name:  IMG_5404 (Small).JPG
Views: 18692
Size:  47.3 KB
One of the finished top with the joint
Name:  IMG_5405 (Small).JPG
Views: 19306
Size:  47.6 KB
and the final product
Name:  IMG_5403 (Small).JPG
Views: 21540
Size:  44.0 KB
__________________
James
1968 GMC "HAVOC"
1986 GMC "Frank"
J.J.R.H. Design & Consulting

My 68`Rebuild "HAVOC": http://67-72chevytrucks.com/vboard/s...d.php?t=316300
A 58' chev build thread: http://www.67-72chevytrucks.com/vboa...d.php?t=311238
1969 Camaro Pro Touring http://67-72chevytrucks.com/vboard/s...61#post3513361
Swiss Cheese: http://67-72chevytrucks.com/vboard/s...d.php?t=384390
Adjustable Trailing Arm How-To: http://67-72chevytrucks.com/vboard/s...d.php?t=321100
1968 Ford Farm Truck: http://67-72chevytrucks.com/vboard/s...=1#post6555587
nuke1 is offline   Reply With Quote
Old 12-29-2008, 02:00 AM   #3
nuke1
Registered User
 
nuke1's Avatar
 
Join Date: Jun 2007
Location: Saskatoon, Saskatchewan,:
Posts: 2,901
Re: Adjustable rear trailing arms how-to

Here is a few more pics also, and a list of materials i used.

LIST:
Two 53.5 inch lengths of 2" x 3" x 3/16" tubing
2 Ballistic Joints
11 gauge sheetmetal
2 two 5 " lengths of DOM tubing

that is it, u can use whatever joints you want to, but this is what i did. and make sure you USE A SUFFICIENT WELDER TO DO THIS.

Anyways, thank you and enjoy

JAMES
Attached Images
  
__________________
James
1968 GMC "HAVOC"
1986 GMC "Frank"
J.J.R.H. Design & Consulting

My 68`Rebuild "HAVOC": http://67-72chevytrucks.com/vboard/s...d.php?t=316300
A 58' chev build thread: http://www.67-72chevytrucks.com/vboa...d.php?t=311238
1969 Camaro Pro Touring http://67-72chevytrucks.com/vboard/s...61#post3513361
Swiss Cheese: http://67-72chevytrucks.com/vboard/s...d.php?t=384390
Adjustable Trailing Arm How-To: http://67-72chevytrucks.com/vboard/s...d.php?t=321100
1968 Ford Farm Truck: http://67-72chevytrucks.com/vboard/s...=1#post6555587
nuke1 is offline   Reply With Quote
Old 12-29-2008, 02:43 AM   #4
joe231
Registered User
 
joe231's Avatar
 
Join Date: Dec 2007
Location: Palmer, Alaska
Posts: 13,821
Re: Adjustable rear trailing arms how-to

wow man!
very cool write up!
thanks!
how do you figure they compare to the stock ones, weight wise?
__________________
CHEVY ONLY
joe231 is offline   Reply With Quote
Old 12-29-2008, 03:09 AM   #5
nuke1
Registered User
 
nuke1's Avatar
 
Join Date: Jun 2007
Location: Saskatoon, Saskatchewan,:
Posts: 2,901
Re: Adjustable rear trailing arms how-to

I will weigh them tomorow for you and let yo know.
__________________
James
1968 GMC "HAVOC"
1986 GMC "Frank"
J.J.R.H. Design & Consulting

My 68`Rebuild "HAVOC": http://67-72chevytrucks.com/vboard/s...d.php?t=316300
A 58' chev build thread: http://www.67-72chevytrucks.com/vboa...d.php?t=311238
1969 Camaro Pro Touring http://67-72chevytrucks.com/vboard/s...61#post3513361
Swiss Cheese: http://67-72chevytrucks.com/vboard/s...d.php?t=384390
Adjustable Trailing Arm How-To: http://67-72chevytrucks.com/vboard/s...d.php?t=321100
1968 Ford Farm Truck: http://67-72chevytrucks.com/vboard/s...=1#post6555587
nuke1 is offline   Reply With Quote
Old 12-29-2008, 03:18 AM   #6
Frizzle Fry
Registered User
 
Frizzle Fry's Avatar
 
Join Date: Aug 2005
Location: Hillsboro Oregon
Posts: 6,449
Re: Adjustable rear trailing arms how-to

That's sweet man! Great idea!
Frizzle Fry is offline   Reply With Quote
Old 12-29-2008, 03:44 AM   #7
RunninLo
3DrDwn--the 'burb not the band
 
RunninLo's Avatar
 
Join Date: Jan 2007
Location: missoula, mt
Posts: 598
Re: Adjustable rear trailing arms how-to

Very cool and a great way to replace rusted out arms. If you could figure a way to step them and adjust the pinion angle back into spec they would be an awesome alternative to drop block plus arms. The posibilites are really there for this idea. Again.. way cool
__________________
Slo and Lo that is the tempo.
'72 burb build page here:
http://67-72chevytrucks.com/vboard/s...d.php?t=259256

'89 GMC Dually crew build page coming soon.
88 4x4 crew DD

duallys past/present pics here:
http://67-72chevytrucks.com/vboard/s...46#post4001246

89 1 ton Dually rear flip kit install here:
http://67-72chevytrucks.com/vboard/s...d.php?t=354327
RunninLo is offline   Reply With Quote
Old 12-29-2008, 10:42 AM   #8
joe231
Registered User
 
joe231's Avatar
 
Join Date: Dec 2007
Location: Palmer, Alaska
Posts: 13,821
Re: Adjustable rear trailing arms how-to

Quote:
Originally Posted by nuke1 View Post
I will weigh them tomorow for you and let yo know.
cool, thanks!
__________________
CHEVY ONLY
joe231 is offline   Reply With Quote
Old 12-29-2008, 12:12 PM   #9
Shane
Account Suspended
 
Shane's Avatar
 
Join Date: Jun 2000
Location: over yonder
Posts: 14,270
Re: Adjustable rear trailing arms how-to

Very very nice write up. Thanks!
Shane is offline   Reply With Quote
Old 12-29-2008, 12:38 PM   #10
SCOTI
Registered User
 
SCOTI's Avatar
 
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 21,894
Re: Adjustable rear trailing arms how-to

Quote:
Originally Posted by RunninLo View Post
Very cool and a great way to replace rusted out arms. If you could figure a way to step them and adjust the pinion angle back into spec they would be an awesome alternative to drop block plus arms. The posibilites are really there for this idea. Again.. way cool
I was thinking the same thing.
__________________
67SWB-B.B.RetroRod
64SWB-Recycle
89CCDually-Driver/Tow Truck
99CCSWB Driver
All Fleetsides
@rattlecankustoms in IG

Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive.
It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar.....

Cubic inches is like Indiana Jones with a cheap pistol.
SCOTI is offline   Reply With Quote
Old 12-29-2008, 06:56 PM   #11
72hotrodder
THE TOY STORE
 
72hotrodder's Avatar
 
Join Date: Nov 2008
Location: florence al
Posts: 227
Re: Adjustable rear trailing arms how-to

is there anyway i can bookmard this thread of something
72hotrodder is offline   Reply With Quote
Old 12-29-2008, 11:13 PM   #12
N2TRUX
Happy to be here
 
N2TRUX's Avatar
 
Join Date: Mar 2000
Location: Cypress, TX
Posts: 39,023
Re: Adjustable rear trailing arms how-to

Quote:
Originally Posted by 72hotrodder View Post
is there anyway i can bookmard this thread of something
You can subscribe to it through the forum, or you can bookmark it through your browser.
__________________
Follow me on Facebook and Instagram @N2trux.com

Articles-

"Jake" the 84 to 74 crewcab

"Elwood" the77_Remix

85 GMC Sierra "Scarlett"

"Refining Sierra"
N2TRUX is offline   Reply With Quote
Old 12-29-2008, 11:43 PM   #13
protrash64
Resistance is Futile
 
protrash64's Avatar
 
Join Date: Dec 2006
Location: Mesa,Arizona
Posts: 3,519
Re: Adjustable rear trailing arms how-to

What are you doing for the mounts at the front? I noticed that they were cut from the X-member. Nice work, time to go into production!!!
__________________
64 CHEVY PICK-UP > http://67-72chevytrucks.com/vboard/s...otrash+re-hash
64 CARRYALL >http://67-72chevytrucks.com/vboard/s...=1964+suburban
66 LB >http://67-72chevytrucks.com/vboard/s...d.php?t=427852
STRENGTH/DETERMINATION/MERCILESS/FOREVER
.......posted via stationary device
protrash64 is offline   Reply With Quote
Old 12-30-2008, 12:36 AM   #14
nuke1
Registered User
 
nuke1's Avatar
 
Join Date: Jun 2007
Location: Saskatoon, Saskatchewan,:
Posts: 2,901
Re: Adjustable rear trailing arms how-to

Quote:
Originally Posted by joe231 View Post
wow man!
very cool write up!
thanks!
how do you figure they compare to the stock ones, weight wise?


Weight wise, i weighed them tonite and they weighed 4 lbs less than the originals, so a savings of 8lbs, although i do not think that is gonna help me much with what i am doing, but every bit counts.

James
__________________
James
1968 GMC "HAVOC"
1986 GMC "Frank"
J.J.R.H. Design & Consulting

My 68`Rebuild "HAVOC": http://67-72chevytrucks.com/vboard/s...d.php?t=316300
A 58' chev build thread: http://www.67-72chevytrucks.com/vboa...d.php?t=311238
1969 Camaro Pro Touring http://67-72chevytrucks.com/vboard/s...61#post3513361
Swiss Cheese: http://67-72chevytrucks.com/vboard/s...d.php?t=384390
Adjustable Trailing Arm How-To: http://67-72chevytrucks.com/vboard/s...d.php?t=321100
1968 Ford Farm Truck: http://67-72chevytrucks.com/vboard/s...=1#post6555587
nuke1 is offline   Reply With Quote
Old 12-30-2008, 12:38 AM   #15
nuke1
Registered User
 
nuke1's Avatar
 
Join Date: Jun 2007
Location: Saskatoon, Saskatchewan,:
Posts: 2,901
Re: Adjustable rear trailing arms how-to

Quote:
Originally Posted by protrash64 View Post
What are you doing for the mounts at the front? I noticed that they were cut from the X-member. Nice work, time to go into production!!!


The mounts on the front are being made from 3/16th steel plate, check my build up of HAVOC and this will explain more, the frame is no where near original any more, as for production, , there is always a possibility,
__________________
James
1968 GMC "HAVOC"
1986 GMC "Frank"
J.J.R.H. Design & Consulting

My 68`Rebuild "HAVOC": http://67-72chevytrucks.com/vboard/s...d.php?t=316300
A 58' chev build thread: http://www.67-72chevytrucks.com/vboa...d.php?t=311238
1969 Camaro Pro Touring http://67-72chevytrucks.com/vboard/s...61#post3513361
Swiss Cheese: http://67-72chevytrucks.com/vboard/s...d.php?t=384390
Adjustable Trailing Arm How-To: http://67-72chevytrucks.com/vboard/s...d.php?t=321100
1968 Ford Farm Truck: http://67-72chevytrucks.com/vboard/s...=1#post6555587
nuke1 is offline   Reply With Quote
Old 12-30-2008, 12:41 AM   #16
nuke1
Registered User
 
nuke1's Avatar
 
Join Date: Jun 2007
Location: Saskatoon, Saskatchewan,:
Posts: 2,901
Re: Adjustable rear trailing arms how-to

Quote:
Originally Posted by RunninLo View Post
Very cool and a great way to replace rusted out arms. If you could figure a way to step them and adjust the pinion angle back into spec they would be an awesome alternative to drop block plus arms. The posibilites are really there for this idea. Again.. way cool
the stepping of the arms would be easy, as for the pinion angle, well that is a different matter, where the arms are connected to the crossmember, is where my adjustability will be, but things can always change, if you had a set ride height in mind, you can set you pinion angle and weld them to match that, just a little more time, but not bad.
__________________
James
1968 GMC "HAVOC"
1986 GMC "Frank"
J.J.R.H. Design & Consulting

My 68`Rebuild "HAVOC": http://67-72chevytrucks.com/vboard/s...d.php?t=316300
A 58' chev build thread: http://www.67-72chevytrucks.com/vboa...d.php?t=311238
1969 Camaro Pro Touring http://67-72chevytrucks.com/vboard/s...61#post3513361
Swiss Cheese: http://67-72chevytrucks.com/vboard/s...d.php?t=384390
Adjustable Trailing Arm How-To: http://67-72chevytrucks.com/vboard/s...d.php?t=321100
1968 Ford Farm Truck: http://67-72chevytrucks.com/vboard/s...=1#post6555587
nuke1 is offline   Reply With Quote
Old 12-30-2008, 10:45 AM   #17
joe231
Registered User
 
joe231's Avatar
 
Join Date: Dec 2007
Location: Palmer, Alaska
Posts: 13,821
Re: Adjustable rear trailing arms how-to

thanks for the info
__________________
CHEVY ONLY
joe231 is offline   Reply With Quote
Old 01-16-2009, 02:03 PM   #18
NPilot1975
Senior Member
 
NPilot1975's Avatar
 
Join Date: Aug 2002
Location: Plymouth, MA
Posts: 891
Re: Adjustable rear trailing arms how-to

Great thread! I may have missed it but what was the actual angle that you used for your pie cut? I would love to build a set of these, although I don't think I would worry about the adjustable end.
__________________
1972 Blazer body...need to get a thread started for the rest of the story
NPilot1975 is offline   Reply With Quote
Old 01-16-2009, 04:13 PM   #19
aggie91
I'm just glad to be here!
 
aggie91's Avatar
 
Join Date: Jan 2008
Location: Longview, TX
Posts: 4,788
Re: Adjustable rear trailing arms how-to

Looks good! I have to follow this one..
__________________
Karl



1965 Chevy Stepside(Grandpa's Old Blue) and (July 2015 Shop Build!)(2020, the Saga Continues)
http://67-72chevytrucks.com/vboard/s...d.php?t=372424

The LST Challenge:
http://67-72chevytrucks.com/vboard/s...=1#post7812257

Korbin's 1st Square: "Sunburn"
http://67-72chevytrucks.com/vboard/s...d.php?t=418618

1985 GMC Sierra: "White Trash", Korbin's 2nd now...
http://67-72chevytrucks.com/vboard/s...d.php?t=632305

Henry - 1984 Chevrolet, Owen's 1st Square
aggie91 is offline   Reply With Quote
Old 01-19-2009, 02:27 PM   #20
C20-67_N_MO
Champagne Taste on Beer Budget
 
C20-67_N_MO's Avatar
 
Join Date: Dec 2008
Location: High Ridge, Missouri
Posts: 2,190
Re: Adjustable rear trailing arms how-to

Iffin I had the equipment and know-how would be making a set for my '67 as well.

How much time & money do you have invested in this? I know the new trailing arms are quite expensive. As far as the adjustable ends where do you find those?

Great write up, thanks for sharing with everyone.
__________________
Coming Soon: Project 1970 Country Truck
C20-67_N_MO is offline   Reply With Quote
Old 01-20-2009, 01:27 AM   #21
nuke1
Registered User
 
nuke1's Avatar
 
Join Date: Jun 2007
Location: Saskatoon, Saskatchewan,:
Posts: 2,901
Re: Adjustable rear trailing arms how-to

hey guys, total investment for the control arems with the end links is about 140 dollars as for time about 6 hours, the adjustable ends are from ballistic fabrication and as for the pie cut, i figured out my angle with an angle finder, what you could do is bend a wire the original bend of the arms and now use it for you bend, but you have to use the other side of it, i am not sure that makes sense, i will try to get a pic of what i mean for tomorow night for you , is that ok.

JAMES
__________________
James
1968 GMC "HAVOC"
1986 GMC "Frank"
J.J.R.H. Design & Consulting

My 68`Rebuild "HAVOC": http://67-72chevytrucks.com/vboard/s...d.php?t=316300
A 58' chev build thread: http://www.67-72chevytrucks.com/vboa...d.php?t=311238
1969 Camaro Pro Touring http://67-72chevytrucks.com/vboard/s...61#post3513361
Swiss Cheese: http://67-72chevytrucks.com/vboard/s...d.php?t=384390
Adjustable Trailing Arm How-To: http://67-72chevytrucks.com/vboard/s...d.php?t=321100
1968 Ford Farm Truck: http://67-72chevytrucks.com/vboard/s...=1#post6555587

Last edited by N2TRUX; 02-18-2010 at 10:40 AM.
nuke1 is offline   Reply With Quote
Old 03-04-2009, 11:26 AM   #22
joe231
Registered User
 
joe231's Avatar
 
Join Date: Dec 2007
Location: Palmer, Alaska
Posts: 13,821
Re: Adjustable rear trailing arms how-to

Any update on the wire guide?
__________________
CHEVY ONLY
joe231 is offline   Reply With Quote
Old 03-04-2009, 12:03 PM   #23
nuke1
Registered User
 
nuke1's Avatar
 
Join Date: Jun 2007
Location: Saskatoon, Saskatchewan,:
Posts: 2,901
Re: Adjustable rear trailing arms how-to

i will do it today, sorry for the delay
__________________
James
1968 GMC "HAVOC"
1986 GMC "Frank"
J.J.R.H. Design & Consulting

My 68`Rebuild "HAVOC": http://67-72chevytrucks.com/vboard/s...d.php?t=316300
A 58' chev build thread: http://www.67-72chevytrucks.com/vboa...d.php?t=311238
1969 Camaro Pro Touring http://67-72chevytrucks.com/vboard/s...61#post3513361
Swiss Cheese: http://67-72chevytrucks.com/vboard/s...d.php?t=384390
Adjustable Trailing Arm How-To: http://67-72chevytrucks.com/vboard/s...d.php?t=321100
1968 Ford Farm Truck: http://67-72chevytrucks.com/vboard/s...=1#post6555587
nuke1 is offline   Reply With Quote
Old 03-04-2009, 12:06 PM   #24
MickMc
Registered User
 
MickMc's Avatar
 
Join Date: Feb 2008
Location: Albuquerque
Posts: 359
Re: Adjustable rear trailing arms how-to

Quote:
Originally Posted by nuke1 View Post
Well, i had that end of the arms done for now so on to the other end, because i was using flex joints, i got some DOM tubing threaded to accept my joints, the threads are 1 1/4". the sleeves are 5 inches long. on the end of the sleeves i attached some square solid stock in a cross fashin, this was then welded up to the DOM tubing. i made a plate for the other end of the tubing as well, i cut a hole in it with a hole saw and my drill press. i proceeded to insert the section now into the arm. i drilled four holes in the arm that equates to where the solid stock will be. i left the end of the DOM tubing sticking out 3/16" for welding. i also welded the backside of it, but make sure that you get it square.
Attachment 415993
]


Do you have any other pictures of the "on the end of the sleeves i attached some square solid stock in a cross fashin,"?
Maybe a couple of pictures will clear it up for me.


Mick
MickMc is offline   Reply With Quote
Old 03-04-2009, 01:14 PM   #25
SCOTI
Registered User
 
SCOTI's Avatar
 
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 21,894
Re: Adjustable rear trailing arms how-to

Quote:
Originally Posted by MickMc View Post
Do you have any other pictures of the "on the end of the sleeves i attached some square solid stock in a cross fashin,"?
Maybe a couple of pictures will clear it up for me.


Mick
Looking @ the pics, it seems that he inseted square solid steel into the end of the sq tubing & plug welded it from each side of the tubing to hold it in place.
__________________
67SWB-B.B.RetroRod
64SWB-Recycle
89CCDually-Driver/Tow Truck
99CCSWB Driver
All Fleetsides
@rattlecankustoms in IG

Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive.
It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar.....

Cubic inches is like Indiana Jones with a cheap pistol.
SCOTI is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 02:23 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com