The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Engine & Drivetrain > LSx Swaps

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 12-05-2018, 09:40 AM   #1
bb400ho
Active Member
 
Join Date: Jun 2017
Location: erie pa
Posts: 150
stock cooling fan

does anyone run the stock cooling fan on a 5.3 swap? if so does the small block fan shroud work with it?.
thanks Bryan
bb400ho is offline   Reply With Quote
Old 12-05-2018, 12:24 PM   #2
ls1nova71
Registered User
 
ls1nova71's Avatar
 
Join Date: Dec 2009
Location: Independence Mo
Posts: 4,117
Re: stock cooling fan

I usually run the stock fan. Fits the fan shroud and never had any cooling problems, even with the A/C on.
__________________
My '72 short bed build. http://www.ls1tech.com/forums/conver...6-0-4l80e.html

5.3 swap into my RUSTY '71 C10
http://ls1tech.com/forums/conversion...71-c-10-a.html
ls1nova71 is offline   Reply With Quote
Old 12-05-2018, 02:43 PM   #3
bb400ho
Active Member
 
Join Date: Jun 2017
Location: erie pa
Posts: 150
Re: stock cooling fan

Thanks I was hoping I could use a stock shroud. I was worried that the fan was a little too low.Is yours from a 6cyl or a small block? I have a champion aluminum rad but I think a shroud will work
thanks Bryan
bb400ho is offline   Reply With Quote
Old 12-05-2018, 05:41 PM   #4
Wgesnerjr
Senior Member
 
Wgesnerjr's Avatar
 
Join Date: Jun 2015
Location: Atlanta, GA.
Posts: 737
Re: stock cooling fan

Used the factory Fan from the 5.3 with the 1985 SBC fan shroud. Mine fit perfectly but it might depend on the mounting plates you use. I lucked out and got a no-name set off eBay that worked but do not remember the vendor.
__________________
Jay Gesner
Atlanta, GA
1985 C10 Long Bed 4X2
LS 5.3, 4L60E
Father/Daughter Project
Wgesnerjr is offline   Reply With Quote
Old 12-05-2018, 05:54 PM   #5
72MARIO
Registered User
 
72MARIO's Avatar
 
Join Date: Nov 2000
Location: Huntsville Ontario Canada
Posts: 4,052
Re: stock cooling fan

I used the 6.0 clutch fan in my 1968 suburban
I would replace the thermostat clutch as I did have mine go bad. It wouldnt engage and pull air.
__________________
1968 Suburban numbers matching all original truck now equipped with 6.0/4L80 on Accuair
http://67-72chevytrucks.com/vboard/s...d.php?t=625017
1967 C/20 6.0/4L80 Roofing Truck
1990 V2500 Suburban "Plow Truck"
2005 TAHOE DD
72MARIO is offline   Reply With Quote
Old 12-06-2018, 10:11 AM   #6
bb400ho
Active Member
 
Join Date: Jun 2017
Location: erie pa
Posts: 150
Re: stock cooling fan

Thanks for the info. glad to know it should work. i have the wires for the electric fans but i would just rather go this way if it works
thanks Bryan
bb400ho is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:53 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com