Billet Aluminum Dash Panels and Glove Box Doors - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Ryan Hubbard · 12-14-2009, 05:18 PM

Quote:

Originally Posted by Thealien

Any chance of gettin one with only the light/wiper holes or none at all?

NO! Too hard to hold down and machine the outside. I use the gauge holes to clamp the piece down to the table.

Thealien · 12-15-2009, 08:57 AM

Quote:

Originally Posted by Ryan Hubbard

NO! Too hard to hold down and machine the outside. I use the gauge holes to clamp the piece down to the table.

How about if you made a hole in the center to clamp it down? I will eventually be cutting out a lot of the center. I want to install a 2005 cluster in my Jimmy someday to go with the 2005 engine I am installing. I will want to cut out the center to frame that cluster? I am in no rush either I could wait until you do another batch?

Thealien · 12-20-2009, 12:15 PM

No?

Ryan Hubbard · 12-21-2009, 03:07 PM

I cannot justify doing one or two solid panels with all the mods I have to make to the program and the tooling without making the price significantly higher. And from past experience, most people won't pay the extra money.

2 Many Toys · 01-01-2010, 08:16 PM

When is this deal over? I am in Cali so what is the total?

Thealien · 01-01-2010, 08:30 PM

Quote:

Originally Posted by Ryan Hubbard

I cannot justify doing one or two solid panels with all the mods I have to make to the program and the tooling without making the price significantly higher. And from past experience, most people won't pay the extra money.

I thought it would be less work? I would have waited until you did another run? Oh well thanks anyway

**rob32472** · 01-02-2010, 09:30 AM

are these still avail? and can you do 3 3/8 for tach and speedo?

Dusty71blazer · 01-02-2010, 03:55 PM

Looks sweet- adding to my wishlist

*Shane* · 01-02-2010, 04:58 PM

Quote:

Originally Posted by Ryan Hubbard

NO! Too hard to hold down and machine the outside. I use the gauge holes to clamp the piece down to the table.

use toe clamps & double sided tape on it ... stop the machine as you approach the clamps using an optional stop or a feed hold ... remove clamp ... cut ... replace clamp

Ryan Hubbard · 01-02-2010, 10:59 PM

Quote:

Originally Posted by 2 Many Toys

When is this deal over? I am in Cali so what is the total?

The deal is over when they are gone. I have eight sets left.

*mickeymouse* · 04-11-2010, 03:43 PM

Payment sent.

Last posted was eight left?

Ryan Hubbard · 04-12-2010, 02:05 PM

I will have it sent out today. Thanks for the business.

*mickeymouse* · 04-21-2010, 09:43 AM

Bump for a SCHWEET deal.

Just got mine last week!

bcdeutsch731 · 04-28-2010, 10:26 AM

Can I get one made with no head light and wiper hole in it? Also would it be possable to get it made with two 5" holes and five 2 5/8", one 2 5/8" hole being in the center and the other four at the bottom? If you can do it like that what would the price be just for the Dash? Thanks

Ryan Hubbard · 05-01-2010, 12:36 AM

Quote:

Originally Posted by bcdeutsch731

Can I get one made with no head light and wiper hole in it? Also would it be possable to get it made with two 5" holes and five 2 5/8", one 2 5/8" hole being in the center and the other four at the bottom? If you can do it like that what would the price be just for the Dash? Thanks

I looked into it and they won't fit on the dash panel. Not enough room.

Ryan Hubbard · 05-01-2010, 12:38 AM

Quote:

Originally Posted by rob32472

are these still avail? and can you do 3 3/8 for tach and speedo?

I have them set up for that but I would need to get a run of at least ten to make it worth while to run on the machine. I am just trying to clear out my inventory.

bcdeutsch731 · 05-01-2010, 08:46 AM

Thanks for looking into it. If you can't do the 2 5/8 than can I get one made with two 5" holes and five 2 1/16 holes with out the wiper and light holes? If you can do it how much will it cost?
Thanks

mbhabsfan · 05-05-2010, 01:45 PM

any left? email me at kenmc@mts.net with payment info and I will reply with shipping adress etc. Thanks

snj8198 · 05-06-2010, 10:50 AM

im interested if you let me know what you have left.

Ryan Hubbard · 05-06-2010, 11:12 AM

Quote:

Originally Posted by snj8198

im interested if you let me know what you have left.

PM sent and Yes I still have some left.

DYNAMiTE · 05-20-2010, 03:53 AM

I need one with 2- 5" and 5 2 1/16" are these still available?

bcdeutsch731 · 05-20-2010, 08:06 AM

I need the same thing as above but with no wiper and head light holes can you do this?

SWB4x4 · 08-11-2010, 04:47 PM

how much for a glove box door shipped to 95991 (CA btw)

Jparks · 08-22-2010, 02:31 PM

Do you have any available with just the 2 - 5" holes, and of course the wiper and headlight holes too?

NorCalTank · 11-22-2010, 06:21 PM

Just need a glove box door. price shipped to 96007?

12-20-2009, 12:15 PM	#28
Thealien Senior Member Join Date: Jun 2007 Location: Pine Ridge Florida Posts: 4,126	Re: Billet Aluminum Dash Panels and Glove Box Doors No?

12-21-2009, 03:07 PM	#29
Ryan Hubbard Registered User Join Date: Aug 2007 Location: Mission Viejo, CA Posts: 288	Re: Billet Aluminum Dash Panels and Glove Box Doors I cannot justify doing one or two solid panels with all the mods I have to make to the program and the tooling without making the price significantly higher. And from past experience, most people won't pay the extra money.

01-01-2010, 08:16 PM	#30
2 Many Toys Registered User Join Date: Dec 2007 Location: Stockton Ca Posts: 18	Re: Billet Aluminum Dash Panels and Glove Box Doors When is this deal over? I am in Cali so what is the total?

01-02-2010, 09:30 AM	#32
rob32472 Registered User Join Date: May 2007 Location: dallas ga Posts: 1,503	Re: Billet Aluminum Dash Panels and Glove Box Doors are these still avail? and can you do 3 3/8 for tach and speedo? Last edited by rob32472; 01-02-2010 at 09:53 AM.

01-02-2010, 03:55 PM	#33
Dusty71blazer Registered User Join Date: Nov 2009 Location: Sioux City, IA Posts: 158	Re: Billet Aluminum Dash Panels and Glove Box Doors Looks sweet- adding to my wishlist __________________ Dustin '97 Dodge Ram (daily driver) '71 Blazer (supposed to be a toy... insists on being a project) '85 Monte Carlo SS (project)

04-11-2010, 03:43 PM	#36
mickeymouse Account Suspended Join Date: Nov 2005 Location: Where ever the Navy sends me. Posts: 116	Re: Billet Aluminum Dash Panels and Glove Box Doors Payment sent. Last posted was eight left?

04-12-2010, 02:05 PM	#37
Ryan Hubbard Registered User Join Date: Aug 2007 Location: Mission Viejo, CA Posts: 288	Re: Billet Aluminum Dash Panels and Glove Box Doors I will have it sent out today. Thanks for the business.

04-21-2010, 09:43 AM	#38
mickeymouse Account Suspended Join Date: Nov 2005 Location: Where ever the Navy sends me. Posts: 116	Re: Billet Aluminum Dash Panels and Glove Box Doors Bump for a SCHWEET deal. Just got mine last week!

04-28-2010, 10:26 AM	#39
bcdeutsch731 Registered User Join Date: Mar 2010 Location: West Chicago, IL Posts: 140	Re: Billet Aluminum Dash Panels and Glove Box Doors Can I get one made with no head light and wiper hole in it? Also would it be possable to get it made with two 5" holes and five 2 5/8", one 2 5/8" hole being in the center and the other four at the bottom? If you can do it like that what would the price be just for the Dash? Thanks __________________ 1969 C10, 2005 LLY Duramax, Wagler Competition built motor, Bullseye Power triple Turbo's, Rossler th400, Neal Chance Racing Converter, Danville Performance tunning. 8.3@168mph 1700+ HP

05-01-2010, 08:46 AM	#42
bcdeutsch731 Registered User Join Date: Mar 2010 Location: West Chicago, IL Posts: 140	Re: Billet Aluminum Dash Panels and Glove Box Doors Thanks for looking into it. If you can't do the 2 5/8 than can I get one made with two 5" holes and five 2 1/16 holes with out the wiper and light holes? If you can do it how much will it cost? Thanks __________________ 1969 C10, 2005 LLY Duramax, Wagler Competition built motor, Bullseye Power triple Turbo's, Rossler th400, Neal Chance Racing Converter, Danville Performance tunning. 8.3@168mph 1700+ HP

05-05-2010, 01:45 PM	#43
mbhabsfan Registered User Join Date: Jan 2008 Location: Manitoba Posts: 24	Re: Billet Aluminum Dash Panels and Glove Box Doors any left? email me at kenmc@mts.net with payment info and I will reply with shipping adress etc. Thanks

05-06-2010, 10:50 AM	#44
snj8198 Registered User Join Date: Feb 2007 Location: Star Valley, WY Posts: 2,038	Re: Billet Aluminum Dash Panels and Glove Box Doors im interested if you let me know what you have left. __________________ Steve 1971 GMC Longbox. Full Roller Stroker 489 w/ FiTech EFI, Chris Straub Cam/NV4500/205/D60/14B w. Grizzly Locker and 4.11's. 2" Lift on 33's

05-20-2010, 03:53 AM	#46
DYNAMiTE Registered User Join Date: Jan 2010 Location: Forney, TX Posts: 35	Re: Billet Aluminum Dash Panels and Glove Box Doors I need one with 2- 5" and 5 2 1/16" are these still available?

05-20-2010, 08:06 AM	#47
bcdeutsch731 Registered User Join Date: Mar 2010 Location: West Chicago, IL Posts: 140	Re: Billet Aluminum Dash Panels and Glove Box Doors I need the same thing as above but with no wiper and head light holes can you do this? __________________ 1969 C10, 2005 LLY Duramax, Wagler Competition built motor, Bullseye Power triple Turbo's, Rossler th400, Neal Chance Racing Converter, Danville Performance tunning. 8.3@168mph 1700+ HP

08-11-2010, 04:47 PM	#48
SWB4x4 Registered User Join Date: Jan 2010 Location: Nor*Cal CALIFORNIA Posts: 157	Re: Billet Aluminum Dash Panels and Glove Box Doors how much for a glove box door shipped to 95991 (CA btw) __________________ J.T. 1972 SWB 4X4 on 35"s with 6" lift all around 3/4 ton running gear with high steer and 4.88s 350/th350. SOON TO BE DONE:2" higher in front 37"s,LSX Swap,Hugger Orange & White Paint Scheme,Air Conditioning,Power Windows & Locks,Complete Gauge Kit,Tank Relocation,Double Din Nav with full Audio System. My Build Thread http://67-72chevytrucks.com/vboard/s...=1#post4169140



Register or Log In To remove these advertisements.

08-22-2010, 02:31 PM	#49
Jparks Registered User Join Date: Aug 2010 Location: Nederland, TX Posts: 429	Re: Billet Aluminum Dash Panels and Glove Box Doors Do you have any available with just the 2 - 5" holes, and of course the wiper and headlight holes too? __________________ 72 SWB - Porterbuilt Front/Rear, 22's, 496bbc - "Outkast" 68 Stepside - Porterbuilt Coilover Chassis, 22's, LS3 - "Badfinger"

11-22-2010, 06:21 PM	#50
NorCalTank Registered User Join Date: Aug 2007 Location: South GA Posts: 72	Re: Billet Aluminum Dash Panels and Glove Box Doors Just need a glove box door. price shipped to 96007?

Register or Log In To remove these advertisements.