The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1960 - 1966 Chevrolet & GMC Pickups Message Board > projects and builds

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 07-11-2019, 11:44 PM   #51
Captainfab
60-66 Nut

 
Join Date: Mar 2007
Location: Coeur d'Alene, Idaho
Posts: 22,083
Re: SkinnyG's '61 Apache

Do you realize that most people that have used the '88-'98 spindles have had issues with getting the correct camber?
__________________
Power Steering Box Adapter Plates For Sale HERE
Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE
Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE
Hydroboost Mounting Plates HERE
Captainfab is offline   Reply With Quote
Old 07-11-2019, 11:53 PM   #52
SkinnyG
Registered User
 
SkinnyG's Avatar
 
Join Date: Feb 2012
Location: Beautiful BC, Canada, eh?!
Posts: 793
Re: SkinnyG's '61 Apache

I do realize there will be issues with getting the correct camber. It's sitting at +1 right now. I do not realize others have done this.

I do, however, have a sawzall and a welder and I'm not afraid to use them.

What I AM especially excited about, is that the front track appears to be 66" wheel-mount-to-wheel-mount, which is a very nice fit to my 65" Ford 9" axle I want to run. I'll be using a more modern offset 18" wheel with more back spacing. I think.
__________________
Nostrildamus - 1961 Apache, now under the knife
The Crusty Chevy - 1977 Silverado, shortboxed & dropped, potato-potato.
The Fiendish Firefly - The ultimate engine swap: 5.7lbs in a 1lb bag
The Lethal Locost - Street legal rollerskate
SkinnyG is online now   Reply With Quote
Old 07-12-2019, 01:04 AM   #53
SkinnyG
Registered User
 
SkinnyG's Avatar
 
Join Date: Feb 2012
Location: Beautiful BC, Canada, eh?!
Posts: 793
Re: SkinnyG's '61 Apache

I just went out and took all the shims out (I had 3 per mount), which put me at -0.5 camber. I don't like the level of zero potential adjustment, but -0.5 is actually my goal for a street setup, so I'm good.

I intend to pie-cut the upper ball joint part of the control arm for better movement if I should pull the trigger and air ride this truck. That should give me a bit more negative camber.

With the shims out, the wms-wms width is still a decent 65.75" wide.
__________________
Nostrildamus - 1961 Apache, now under the knife
The Crusty Chevy - 1977 Silverado, shortboxed & dropped, potato-potato.
The Fiendish Firefly - The ultimate engine swap: 5.7lbs in a 1lb bag
The Lethal Locost - Street legal rollerskate
SkinnyG is online now   Reply With Quote
Old 07-16-2019, 12:40 AM   #54
SkinnyG
Registered User
 
SkinnyG's Avatar
 
Join Date: Feb 2012
Location: Beautiful BC, Canada, eh?!
Posts: 793
Re: SkinnyG's '61 Apache

I fabricated some height-adjustable "legs" which I welded to the frame, so I could set the frame absolutely level. Or, at least as level as a 1961 stick-welded truck chassis is going to let me.

I removed the four forward bed mounts because the 12" chop doesn't coincide with any of the bed frame placements (I'll be drilling a couple new holes), and I cut 12" out of the frame sides (vertical cut because that's all the room I have), measured from 7" behind the cab mount.



The trailing arm crossmember pieces were cut free, as were the forward legs of the X (I mis-measured though, and had to add some metal back. By my new measurements it looks like you'd need to cut out 11.25" here, but I might be wrong); Pythagorus failed me.



I tried to heat the X to bend it to where the stubs needed to line up, but it was taking forever and in the end I just sliced them with a cutting disc and welded them back up as needed.

8" was cut off the end of the frame.

Clamped it securely, checked for square, and tacked it thoroughly. I'll weld it up when my arms and shoulders are cooperating with me again.

__________________
Nostrildamus - 1961 Apache, now under the knife
The Crusty Chevy - 1977 Silverado, shortboxed & dropped, potato-potato.
The Fiendish Firefly - The ultimate engine swap: 5.7lbs in a 1lb bag
The Lethal Locost - Street legal rollerskate
SkinnyG is online now   Reply With Quote
Old 07-16-2019, 01:05 AM   #55
SkinnyG
Registered User
 
SkinnyG's Avatar
 
Join Date: Feb 2012
Location: Beautiful BC, Canada, eh?!
Posts: 793
Re: SkinnyG's '61 Apache

__________________
Nostrildamus - 1961 Apache, now under the knife
The Crusty Chevy - 1977 Silverado, shortboxed & dropped, potato-potato.
The Fiendish Firefly - The ultimate engine swap: 5.7lbs in a 1lb bag
The Lethal Locost - Street legal rollerskate
SkinnyG is online now   Reply With Quote
Old 07-16-2019, 09:56 PM   #56
SkinnyG
Registered User
 
SkinnyG's Avatar
 
Join Date: Feb 2012
Location: Beautiful BC, Canada, eh?!
Posts: 793
Re: SkinnyG's '61 Apache

__________________
Nostrildamus - 1961 Apache, now under the knife
The Crusty Chevy - 1977 Silverado, shortboxed & dropped, potato-potato.
The Fiendish Firefly - The ultimate engine swap: 5.7lbs in a 1lb bag
The Lethal Locost - Street legal rollerskate
SkinnyG is online now   Reply With Quote
Old 07-16-2019, 10:21 PM   #57
SkinnyG
Registered User
 
SkinnyG's Avatar
 
Join Date: Feb 2012
Location: Beautiful BC, Canada, eh?!
Posts: 793
Re: SkinnyG's '61 Apache

I inquired at two different machine shops about getting the 9" axles re-drilled to Chevy 5x5 bolt pattern and hub diameter.

One shop (in business for 75 years) had no idea if it could be done.

The other shop (45 years) said worst case (having to weld the old holes closed), it would be $300 per axle. That's $600CDN, or about $450US. I can get Moser to MAKE me new axles for that.....
__________________
Nostrildamus - 1961 Apache, now under the knife
The Crusty Chevy - 1977 Silverado, shortboxed & dropped, potato-potato.
The Fiendish Firefly - The ultimate engine swap: 5.7lbs in a 1lb bag
The Lethal Locost - Street legal rollerskate
SkinnyG is online now   Reply With Quote
Old 07-17-2019, 12:48 AM   #58
SkinnyG
Registered User
 
SkinnyG's Avatar
 
Join Date: Feb 2012
Location: Beautiful BC, Canada, eh?!
Posts: 793
Re: SkinnyG's '61 Apache

Prepped for fishplates this evening. Lots of grinding.

And I have a full box of 5" discs. I only have 4-1/2" grinders.....
__________________
Nostrildamus - 1961 Apache, now under the knife
The Crusty Chevy - 1977 Silverado, shortboxed & dropped, potato-potato.
The Fiendish Firefly - The ultimate engine swap: 5.7lbs in a 1lb bag
The Lethal Locost - Street legal rollerskate
SkinnyG is online now   Reply With Quote
Old 07-17-2019, 02:51 PM   #59
Notch1988
Registered User
 
Notch1988's Avatar
 
Join Date: Aug 2009
Location: Lacombe, Alberta
Posts: 321
Re: SkinnyG's '61 Apache

Quote:
Originally Posted by SkinnyG View Post
I inquired at two different machine shops about getting the 9" axles re-drilled to Chevy 5x5 bolt pattern and hub diameter.

One shop (in business for 75 years) had no idea if it could be done.

The other shop (45 years) said worst case (having to weld the old holes closed), it would be $300 per axle. That's $600CDN, or about $450US. I can get Moser to MAKE me new axles for that.....
If you've got the access hole in the axle or they're 6 bolt you will be SOL for not having to weld. And like you said, cheaper to buy new.
__________________
66 GMC swb dropmember accuair

Link to my build:
My GMC Project
Notch1988 is offline   Reply With Quote
Old 07-17-2019, 09:28 PM   #60
SkinnyG
Registered User
 
SkinnyG's Avatar
 
Join Date: Feb 2012
Location: Beautiful BC, Canada, eh?!
Posts: 793
Re: SkinnyG's '61 Apache

Okay. It's shortened. That was a LOT of work.















Also, my CPP 5" drop coils arrived, along with Summit Brand polyurethane bushings (re-labeled Energy Suspension? They have ES part numbers cast in the bushing....). Stock coil for comparison:



And I'm not sure what to do with this bed mount. If I attach it with the rear hole (right) and drill a new front hole (left), the bed might be too close to the cab. If I attach it with the front hole (left), the bed cross pieces might not line up. Having never done this before, I'm not sure.....

__________________
Nostrildamus - 1961 Apache, now under the knife
The Crusty Chevy - 1977 Silverado, shortboxed & dropped, potato-potato.
The Fiendish Firefly - The ultimate engine swap: 5.7lbs in a 1lb bag
The Lethal Locost - Street legal rollerskate
SkinnyG is online now   Reply With Quote
Old Yesterday, 08:16 PM   #61
SkinnyG
Registered User
 
SkinnyG's Avatar
 
Join Date: Feb 2012
Location: Beautiful BC, Canada, eh?!
Posts: 793
Re: SkinnyG's '61 Apache

I temporarily mounted the 9" on the trailing arms. The top of the diff at full bump is no higher than the top of the frame rails, so that's good. I also ordered new axles with 5 on 5" pattern.....

There does not seem to be a dimension for where the mounts are to go on the axle; consensus seems to be "place them where they work best."







I picked up some 3/16" plate after all. After a fair bit of sitting and staring, I think I've come up with a notch I'm pleased with, though I may mock it up in cardboard entirely to see what I think.

Sharp corners are potential stress risers, so this is intended to reduce stresses. It also maintains a 4" tall frame through the notch as well. The front and back of the axle <em>cut</em> will use part of the original frame. It makes sense in my head.







Going to sleep on it before I bring out the plasma cutter.
__________________
Nostrildamus - 1961 Apache, now under the knife
The Crusty Chevy - 1977 Silverado, shortboxed & dropped, potato-potato.
The Fiendish Firefly - The ultimate engine swap: 5.7lbs in a 1lb bag
The Lethal Locost - Street legal rollerskate
SkinnyG is online now   Reply With Quote
Old Today, 12:08 AM   #62
Captainfab
60-66 Nut

 
Join Date: Mar 2007
Location: Coeur d'Alene, Idaho
Posts: 22,083
Re: SkinnyG's '61 Apache

Are you going to run the 9" at that width? The pinion is a bit offset as it sits now. The trailing arm mounts need to be the same distance from the backing plate on both sides. Then of course you will need to determine the pinion angle. I do make trailing arm mounts sized specifically for the 9" axle tubes.
__________________
Power Steering Box Adapter Plates For Sale HERE
Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE
Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE
Hydroboost Mounting Plates HERE
Captainfab is offline   Reply With Quote
Old Today, 12:15 AM   #63
SkinnyG
Registered User
 
SkinnyG's Avatar
 
Join Date: Feb 2012
Location: Beautiful BC, Canada, eh?!
Posts: 793
Re: SkinnyG's '61 Apache

I -think- am going to run the 9" at full 65" width. With the 18" Grand Cherokee steelies I have, it should fit fine. I -think-. This is also why I'm fine using the 88-98 spindes, and offsetting the balljoint outboard a tick - the front hub to hub is 65-3/4" right now (un-widened). I -think- it will all work out.

The trailing arms are merely placed to hold the axle to know where the tubes are to cut the notch. I will space them exactly once I know there exactly I want the trailing arms to sit with respect to the frame.

I made my own axle saddles at the same 12 of the HO32, but with the arm placement where I think I want the axle, the angle is wrong. Nothing a touch of grinding can't fix.

I will determine pinion angle once I have the engine and trans in and placed, so I can optimize and match the operating angles at the trans and diff. Then wait to finalize it when the whole thing is pretty much at ride weight, sitting on tires, and in need to a driveshaft (I've screwed up in the past ordering driveshafts when vehicles weren't fully complete).

As an aside, I really really appreciate your input on this build, and I really like all the brackets and adapters and things you make for the C10s. Thank you!
__________________
Nostrildamus - 1961 Apache, now under the knife
The Crusty Chevy - 1977 Silverado, shortboxed & dropped, potato-potato.
The Fiendish Firefly - The ultimate engine swap: 5.7lbs in a 1lb bag
The Lethal Locost - Street legal rollerskate
SkinnyG is online now   Reply With Quote
Old Today, 01:37 AM   #64
SkinnyG
Registered User
 
SkinnyG's Avatar
 
Join Date: Feb 2012
Location: Beautiful BC, Canada, eh?!
Posts: 793
Re: SkinnyG's '61 Apache

Though, my math might be suspect. Let's see....

I plunked the Jeep wheels under the box, and under the front clip, and separated the rear wheels 65" hub-to-hub, and the front wheels 65-3/4" hub-to-hub.

The front rim is tucked in 4" from the outer fender edge, the rear 3-1/4" from the fender.

The rear rim inside-to-inside with the Jeep wheels and the 9" is 53", outside-to-outside is 70", a track width of 61.5". The factory HO32 and wheels are 54.5" inside, 67.5 outside, track width of 61". Cool.

The front rim inside-to-inside with the Jeep wheels is 53-3/4", outside-to-outside is 70-3/4", a track width of 62-1/4". Apparently (The original front is stored elsewhere right now), the factory front wheels are 56.6 inside, 69.6 outside, track width of 63.1".

So it looks like I do need to widen the front .425" on either side to match the factory track with these wheels, which I was kind of planning to do (though out-of-my-bum I was winging it with 3/8")

Or leave them; people pay money to have a narrower front for riding low.
__________________
Nostrildamus - 1961 Apache, now under the knife
The Crusty Chevy - 1977 Silverado, shortboxed & dropped, potato-potato.
The Fiendish Firefly - The ultimate engine swap: 5.7lbs in a 1lb bag
The Lethal Locost - Street legal rollerskate
SkinnyG is online now   Reply With Quote
Old Today, 01:38 AM   #65
SkinnyG
Registered User
 
SkinnyG's Avatar
 
Join Date: Feb 2012
Location: Beautiful BC, Canada, eh?!
Posts: 793
Re: SkinnyG's '61 Apache

If they really offend me, I could band the wheels another 1.5" or 2" on the outside....
__________________
Nostrildamus - 1961 Apache, now under the knife
The Crusty Chevy - 1977 Silverado, shortboxed & dropped, potato-potato.
The Fiendish Firefly - The ultimate engine swap: 5.7lbs in a 1lb bag
The Lethal Locost - Street legal rollerskate
SkinnyG is online now   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 12:42 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.
Copyright 1997-2013 67-72chevytrucks.com