The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board > The 1973 - 1991 Blazers, Jimmys, and Suburbans Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 01-08-2019, 06:39 PM   #1
kwmech
Senior Member
 
Join Date: Mar 2003
Location: Colfax-California
Posts: 5,742
Radiator Beef Up

My 91 suburban engine (350 tbi) tries to overheat when I tow in the hills around here, occasionally climbing into the 240 range. I'm thinking about converting/changing over to a 2wd 454 radiator which is wider by 5'' and a 4 core. Anybody done this conversion? I know I'll need a big block shroud and a new/wider pads, anything else?
kwmech is offline   Reply With Quote
Old 01-08-2019, 07:39 PM   #2
Ziegelsteinfaust
Registered User
 
Join Date: Dec 2012
Location: Chino Hills
Posts: 1,661
Re: Radiator Beef Up

You have to move some stuff around to make it work too.

I have been told the core support is different too, but I never compared.
Ziegelsteinfaust is offline   Reply With Quote
Old 01-08-2019, 10:03 PM   #3
kwmech
Senior Member
 
Join Date: Mar 2003
Location: Colfax-California
Posts: 5,742
Re: Radiator Beef Up

Looks like core support may be the same, there is another spot to the right for the diesel radiator
kwmech is offline   Reply With Quote
Old 01-12-2019, 01:04 AM   #4
Zoomad75
K5Camper
 
Zoomad75's Avatar
 
Join Date: Mar 2004
Location: Pueblo, CO
Posts: 1,374
Re: Radiator Beef Up

The big block or 6.2 radiator will fit, but depending on which one you use you need the right brackets to hold it off of the core support. Obviously, you'll need the correct shroud depending on the radiator you intend on using.

I went from the stock 350 radiator to a 6.2 radiator with my 5.3 swap. It ran hot in really high ambient temps at low speeds. On the road or off road. Now with 6.2 radiator installed the highest I've seen the gauge was 200 in 113 degree heat on the Mojave road. The rest of the time it runs at 160 to 170.

The 6.2 stuff is harder to find for the top plate, brackets and shroud. One thing to keep in mind if you move to the bigger size is your evap canister *might* be in the way. I've got dual batteries in my K5 and that 6.2 radiator is really close to the driver's side battery.
__________________
Rob Z.
1975 K5 350/465/205/D44/12b 4" lift on 35's- RIP
1991 K5 5.3L/700r4/241/D44/14b FWC Camper
Zoomad75 is offline   Reply With Quote
Old 01-12-2019, 02:53 AM   #5
kwmech
Senior Member
 
Join Date: Mar 2003
Location: Colfax-California
Posts: 5,742
Re: Radiator Beef Up

I've actually got an 85 truck here at the house with a 6.2 in it. Customer left it here 2 years ago with a bad engine... Hmmmm.
kwmech is offline   Reply With Quote
Old 01-12-2019, 12:52 PM   #6
sweetk30
selective wrench turner guy
 
sweetk30's Avatar
 
Join Date: May 2012
Location: horseheads,ny rust belt
Posts: 2,147
Re: Radiator Beef Up

need more info on current setup .

185* or 195* t-stat ?

2-3 core ?

short or tall version ?

fan shroud or not ?

straight or clutch fan ?

std duty or hd towing / plowing clutch fan ?

how many blades on fan ?

jumping to the biggest rad possible is NOT always the best option from the start .

and a wimpy tbi 350 should not be overheating the system this much .
__________________
77-k30lb BIG truck build .
87-k30lb budget beater build .
85-k30lb the plow machine build .
85-c10sb summer fun toy .
-----------------------------
HOLLEY SNIPER efi = worst case of p.i.t.a i ever had .

EDELBROCK pro flo 4 = best deal going so far . love my setup works great.
sweetk30 is offline   Reply With Quote
Old 01-12-2019, 02:18 PM   #7
kwmech
Senior Member
 
Join Date: Mar 2003
Location: Colfax-California
Posts: 5,742
Re: Radiator Beef Up

Quote:
Originally Posted by sweetk30 View Post
need more info on current setup .

185* or 195* t-stat ?



and a wimpy tbi 350 should not be overheating the system this much .
Did not say it was over heating per se, but when towing it climbs into the 230-240 range on the grades---- 195 stat. All stock but starting to show wear and a little green around the seam of the tank. Hopefully will be starting a 400 sb build this year with the Dart block. Don't want to do the cooling system twice
kwmech is offline   Reply With Quote
Old 01-12-2019, 03:42 PM   #8
sweetk30
selective wrench turner guy
 
sweetk30's Avatar
 
Join Date: May 2012
Location: horseheads,ny rust belt
Posts: 2,147
Re: Radiator Beef Up

i have run a gm 400sbc that was built to the hill . blue printed / balanced / knife edged crank and good cam and heads . use to be in a k10 with 1ton axles / 4.10 gear and 38" tires with th350 trans .

i tryed all combos of 3 core tall rad with and with out shroud and flex fan / clutch fan . she always did 210 98% the time .

most guys going in to the 4 core world tend to find its to much i have read .

might be a easy test and fix with a pusher fan infront of the rad on a temp switch in the intake by the t-stat .

but i understand were your coming from .
__________________
77-k30lb BIG truck build .
87-k30lb budget beater build .
85-k30lb the plow machine build .
85-c10sb summer fun toy .
-----------------------------
HOLLEY SNIPER efi = worst case of p.i.t.a i ever had .

EDELBROCK pro flo 4 = best deal going so far . love my setup works great.
sweetk30 is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 05:25 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.
Copyright 1997-2013 67-72chevytrucks.com