1967 GMC speed minder 351 V6 PS 354 gears - The 1947 - Present Chevrolet & GMC Truck Message Board Network

*sharpie1972* · 11-17-2009, 12:10 AM

Just picked up a 1967 GMC 1/2 ton with quite the option package 351 V6, TH400, Speedminder dash, Power steering (ram set-up), 3.54 axle, Panoramic cab, etc. Looking for some help in coming up with fair prices for parts. The speedminder dash and power steering parts in particular. Thanks, Sharpie

**special-K** · 11-23-2009, 09:31 AM

What color is it?I see it says Special Paint.It looks Palamino Tan.What are the door panels like?

That`s a leaf rear,right?Is it a Dana44 or 60?
The speedminder dash would be $250-300 w/o tach.
The 351 complete should bring $300-$500.
The ram steering is worth a couple hundred or more.Car guys buy them,too.

*sharpie1972* · 11-24-2009, 12:41 AM

Palamino tan sounds right. The original door panels are gone. The one arm rest and the buddy bucket strap are usual silver/tan 67 color. VIN starts with CM. Canadian truck maybe? Sharpie

**special-K** · 11-24-2009, 09:24 AM

Here`s a little tidbit,the "M" is for V6.You know only a few V8s found their way into GMCs at the end of`67?So,that 351 was the big motor through`67.It was even bigger than the big V8 in Chevys (327).
Is the paint kinda pinkish/flesh colored?The`67 front clip that got my project was a Palamino Tan Super Custom from just into Nebraska.The guy I bought it from was from Wyoming.Not that unusual,I guess.But,I get a kick out of the smallest things.

*sharpie1972* · 11-24-2009, 06:39 PM

Yep, that's the color. We already nicknamed her "Pinkie". Funny I had a 67 Chevy with a 327. 46,000 original miles/ I didn't believe the miles until I saw that it came with a 5:13 Locker. Could barely tell if that motor was running or not, it was so smooth. Thanks for the "M" tidbit. Most of my books concentrate on Chevy's.. Little tougher to track down info. on the GMC's. This on has some rather interesting firewall markings, including misspelled "suport" Later, Sharpie

100%Chevy · 11-24-2009, 09:12 PM

The power steering pump and it's mount are getting hard to find.Fit all GMC v/6 engines I believe.So is the alternator mount.
I'd like to see where the 400 trans mounts to the engine if you get it out.
Also keep the auto column and pedals.
Mike.

*sharpie1972* · 11-25-2009, 08:42 AM

I'm also curious about the bellhousing. Does anyone know if the V6 is the standard GM pattern? I'm assuming it is. Also is the flex plate special for the V6? I'm guessing it's an internal balance motor. I've never seen much literature on these. Thanks, Sharpie

*sharpie1972* · 11-25-2009, 09:51 AM

Found lots of info. on the V6's at the 6066GMC guy site. Now I want one of the GMC V12's. They are beastly!

100%Chevy · 11-25-2009, 02:49 PM

The bellhousing pattern is specific to the GMC engines.
I haven't looked at my flywheel though.
I'm wanting to go with an auto in my 64,GMC,but keep the 351.
Mike.

*sharpie1972* · 11-25-2009, 06:16 PM

Looked like there might be an adapter involved according to the 60-66 site. Sharpie

*sharpie1972* · 06-19-2010, 09:18 AM

Gonna part this one guys. Any value input? The speedminder and PS set-up in particular. Thanks, Sharpie

**71blksuper4x4** · 06-20-2010, 02:35 AM

Hey Dennis, I have seen them sale for anywhere from $250-325 w/o tach. I am in desperate need of one of those cables, there weren't very many speed warning setups it seems in Kansas. Hope this helps ya. Tim is on the right track though. Trevor

duallyjams · 06-24-2010, 08:41 AM

Are going to post for sale on this site or ebay-craigslist. I might have interest in some of the V6 equipment.

*sharpie1972* · 06-24-2010, 09:02 AM

Most likely right here, but would like a fair price range on V6 parts. Thanks, Sharpie

PT'S 70 CST · 06-27-2010, 11:28 PM

Speed warning with the cable, buzzer and harness. You are looking at 200-300 depending on the color cond. of the gauge faces.

PT

Rightone1974 · 05-25-2011, 07:05 PM

I just bought a 1968 gmc3/4 ton with the same moter in it. I have power brakes, power steering, and it is also a factory ac truck. I need a carb for it. would anyoneknow how where to get a adapter for a eldbrock or a holley.

11-17-2009, 12:10 AM	#1
sharpie1972 Account Suspended Join Date: Apr 2007 Location: Powell, Wyoming Posts: 4,973	1967 GMC speed minder 351 V6 PS 354 gears Just picked up a 1967 GMC 1/2 ton with quite the option package 351 V6, TH400, Speedminder dash, Power steering (ram set-up), 3.54 axle, Panoramic cab, etc. Looking for some help in coming up with fair prices for parts. The speedminder dash and power steering parts in particular. Thanks, Sharpie Attached Images

11-23-2009, 09:31 AM	#2
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,862	Re: 1967 GMC speed minder 351 V6 PS 354 gears What color is it?I see it says Special Paint.It looks Palamino Tan.What are the door panels like? That`s a leaf rear,right?Is it a Dana44 or 60? The speedminder dash would be $250-300 w/o tach. The 351 complete should bring $300-$500. The ram steering is worth a couple hundred or more.Car guys buy them,too. __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~

11-24-2009, 12:41 AM	#3
sharpie1972 Account Suspended Join Date: Apr 2007 Location: Powell, Wyoming Posts: 4,973	Re: 1967 GMC speed minder 351 V6 PS 354 gears Palamino tan sounds right. The original door panels are gone. The one arm rest and the buddy bucket strap are usual silver/tan 67 color. VIN starts with CM. Canadian truck maybe? Sharpie

11-24-2009, 09:24 AM	#4
special-K Special Order Join Date: Nov 2004 Location: Mt Airy, MD Posts: 85,862	Re: 1967 GMC speed minder 351 V6 PS 354 gears Here`s a little tidbit,the "M" is for V6.You know only a few V8s found their way into GMCs at the end of`67?So,that 351 was the big motor through`67.It was even bigger than the big V8 in Chevys (327). Is the paint kinda pinkish/flesh colored?The`67 front clip that got my project was a Palamino Tan Super Custom from just into Nebraska.The guy I bought it from was from Wyoming.Not that unusual,I guess.But,I get a kick out of the smallest things. __________________ "BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ Last edited by special-K; 11-24-2009 at 09:26 AM.

11-24-2009, 06:39 PM	#5
sharpie1972 Account Suspended Join Date: Apr 2007 Location: Powell, Wyoming Posts: 4,973	Re: 1967 GMC speed minder 351 V6 PS 354 gears Yep, that's the color. We already nicknamed her "Pinkie". Funny I had a 67 Chevy with a 327. 46,000 original miles/ I didn't believe the miles until I saw that it came with a 5:13 Locker. Could barely tell if that motor was running or not, it was so smooth. Thanks for the "M" tidbit. Most of my books concentrate on Chevy's.. Little tougher to track down info. on the GMC's. This on has some rather interesting firewall markings, including misspelled "suport" Later, Sharpie

11-24-2009, 09:12 PM	#6
100%Chevy Registered User Join Date: Jun 2008 Location: Moss Point,Ms. Posts: 1,439	Re: 1967 GMC speed minder 351 V6 PS 354 gears The power steering pump and it's mount are getting hard to find.Fit all GMC v/6 engines I believe.So is the alternator mount. I'd like to see where the 400 trans mounts to the engine if you get it out. Also keep the auto column and pedals. Mike.

11-25-2009, 08:42 AM	#7
sharpie1972 Account Suspended Join Date: Apr 2007 Location: Powell, Wyoming Posts: 4,973	Re: 1967 GMC speed minder 351 V6 PS 354 gears I'm also curious about the bellhousing. Does anyone know if the V6 is the standard GM pattern? I'm assuming it is. Also is the flex plate special for the V6? I'm guessing it's an internal balance motor. I've never seen much literature on these. Thanks, Sharpie

11-25-2009, 09:51 AM	#8
sharpie1972 Account Suspended Join Date: Apr 2007 Location: Powell, Wyoming Posts: 4,973	Re: 1967 GMC speed minder 351 V6 PS 354 gears Found lots of info. on the V6's at the 6066GMC guy site. Now I want one of the GMC V12's. They are beastly! Last edited by sharpie1972; 11-25-2009 at 09:51 AM.

11-25-2009, 02:49 PM	#9
100%Chevy Registered User Join Date: Jun 2008 Location: Moss Point,Ms. Posts: 1,439	Re: 1967 GMC speed minder 351 V6 PS 354 gears The bellhousing pattern is specific to the GMC engines. I haven't looked at my flywheel though. I'm wanting to go with an auto in my 64,GMC,but keep the 351. Mike.

11-25-2009, 06:16 PM	#10
sharpie1972 Account Suspended Join Date: Apr 2007 Location: Powell, Wyoming Posts: 4,973	Re: 1967 GMC speed minder 351 V6 PS 354 gears Looked like there might be an adapter involved according to the 60-66 site. Sharpie

06-19-2010, 09:18 AM	#11
sharpie1972 Account Suspended Join Date: Apr 2007 Location: Powell, Wyoming Posts: 4,973	Re: 1967 GMC speed minder 351 V6 PS 354 gears Gonna part this one guys. Any value input? The speedminder and PS set-up in particular. Thanks, Sharpie Attached Images

06-20-2010, 02:35 AM	#12
71blksuper4x4 SWB 4x4 Collector Join Date: Jun 2001 Location: Osage City, KS Posts: 5,149	Re: 1967 GMC speed minder 351 V6 PS 354 gears Hey Dennis, I have seen them sale for anywhere from $250-325 w/o tach. I am in desperate need of one of those cables, there weren't very many speed warning setups it seems in Kansas. Hope this helps ya. Tim is on the right track though. Trevor __________________ TREVOR 1970 CST swb 4x4 (speedwarning,cruise,tilt,tach,8track, original red shoulder belts,tow hooks) 1972 Jimmy (soon to be Hickey cloned) 1971 Cheyenne Super 4x4 swb (tilt,tach,buckets, original blue shoulder belts,am/fm,cruise,tow hooks, dealer 8 track) 1972 Cheyenne Super K20 4x4 Custom Camper (tilt, tach, am/fm, tow hooks, bed toolbox, aux gas tank 1972 Cheyenne Super Crew Cab K30 4x4 Duramax, Allison, np205, buckets, tow hooks (CURRENT PROJECT) http://67-72chevytrucks.com/vboard/s...d.php?t=624819 1989 V3500 Crew Cab (454tbi, NV4500, np205) 1970 Chevelle SS (LS5 454,th400,8track,buckets,tach) :2004 Jeep Wrangler Rubicon (daily driver) WTB: 1968-70 Cruise Control Lever

06-24-2010, 08:41 AM	#13
duallyjams Registered User Join Date: May 2007 Location: Deale Md Posts: 4,663	Re: 1967 GMC speed minder 351 V6 PS 354 gears Are going to post for sale on this site or ebay-craigslist. I might have interest in some of the V6 equipment. __________________ James 63 GMC V6 4speed carryall 65 chevy swb bbw V8 auto 68 K20 327/4 speed, buddy buckets 2002 GMC CC Dually Duramax 64 GMC lwb 3/4 V6 4speed SOLD 66 GMC swb bbw buddy buckets SOLD IG duallyjams The only thing that stays the same is constant change!

06-24-2010, 09:02 AM	#14
sharpie1972 Account Suspended Join Date: Apr 2007 Location: Powell, Wyoming Posts: 4,973	Re: 1967 GMC speed minder 351 V6 PS 354 gears Most likely right here, but would like a fair price range on V6 parts. Thanks, Sharpie

06-27-2010, 11:28 PM	#15
PT'S 70 CST "GO DAWGS" Join Date: Oct 2003 Location: Batesburg, SC. 29006 Posts: 5,410	Re: 1967 GMC speed minder 351 V6 PS 354 gears Speed warning with the cable, buzzer and harness. You are looking at 200-300 depending on the color cond. of the gauge faces. PT __________________ 70 CST SWB 70 NOVA 93 Indy 500 Pace Truck (SOLD) 94 SILVERADO SWB 5/7 drop 2000 Silverado swb 2005 Nissan Altima 3.5 (Surprisingly very fast) 2004 GMC Yukon XL Denali BATESBURG, SC. 29006 29006 Some of my restorations http://www.snapfish.com/snapfish/thu...NAME=snapfish/ Restored Tach tins 8 cyl - 6 cyl http://67-72chevytrucks.com/vboard/s...d.php?t=518185 Contact info(Not my paypal address) DAWGSFAN227@YAHOO.COM God Bless Our Troops



Register or Log In To remove these advertisements.

05-25-2011, 07:05 PM	#16
Rightone1974 Registered User Join Date: May 2011 Location: Saint Maries Idaho Posts: 24	Re: 1967 GMC speed minder 351 V6 PS 354 gears I just bought a 1968 gmc3/4 ton with the same moter in it. I have power brakes, power steering, and it is also a factory ac truck. I need a carb for it. would anyoneknow how where to get a adapter for a eldbrock or a holley.

Register or Log In To remove these advertisements.