Jeep Coil Spring Drop - The 1947 - Present Chevrolet & GMC Truck Message Board Network

danzka4u · 11-29-2007, 10:21 PM

Hey guys Im new to yor site and I had been looking through the pages and saw a discution on lowering by using jeep coils in the rear and cutting the coils in the front. So I said what the heck lets do it. Here are a couple of photos of my 65. I cut one full coil plus 3 inches in the front I figured I can allways cut more buts its hard to add.

before and after attached I hope

toomanytoyz · 11-29-2007, 10:30 PM

Congrats & Welcome to The Board from Indiana..........

Truck Looks Real Good, What Coils did you use in the Rear??

Rick

danzka4u · 11-30-2007, 10:38 AM

I used 98 wrangler springs. Now that I look at the pictures they don’t really do the drop justice it must be the different angle but the lowered the back about 4 inches.

**slepysal** · 11-30-2007, 11:15 AM

Quote:

Originally Posted by danzka4u

I used 98 wrangler springs. Now that I look at the pictures they don’t really do the drop justice it must be the different angle but the lowered the back about 4 inches.

Thats funny I felt the same when I snaped a few before after pics of my 60.
The jeep springs are a cheep easy swap, but don expect to haul a huge load.
Nice truck and Welcome from Nor Cal !

danzka4u · 11-30-2007, 12:42 PM

Thanks for the welcome.
I dont realy put much in the bed. But I do pull a small trailer with my lawn equipment on it. I just have to take it a little easy over the bumps

ExpeditionXJ · 02-12-2008, 04:20 AM

Quote:

Originally Posted by danzka4u

I used 98 wrangler springs. Now that I look at the pictures they don’t really do the drop justice it must be the different angle but the lowered the back about 4 inches.

Were they front or rear Wrangler coil springs?

This thread just helped me out quite a bit with the fact that you say the Jeep coils are the same diameter and bolt in. I can play with the other tech i know and figure a 3" lift for a trailer project i'm working on that started as a mid 60's stepside.

**ChiefRocka** · 02-12-2008, 04:27 AM

Not so much that are the same diameter...they pigtail on both ends

ExpeditionXJ · 02-12-2008, 04:37 AM

Quote:

Originally Posted by ChiefRocka

Not so much that are the same diameter...they pigtail on both ends

But they should have similar dia to seat in the perch?

I see your sig and dont doubt your input. Guess i gotta get outside and look closely at this.

Thank You Sir.

danzka4u · 02-12-2008, 11:49 PM

Quote:

Originally Posted by ExpeditionXJ

Were they front or rear Wrangler coil springs?

This thread just helped me out quite a bit with the fact that you say the Jeep coils are the same diameter and bolt in. I can play with the other tech i know and figure a 3" lift for a trailer project i'm working on that started as a mid 60's stepside.

The coils were rear and they are not exactly the sane diameter but they do have pig tails at both ends so they fit in the retaining plates. good luck on your trailer.

Steve

Jblackie47803 · 07-21-2009, 04:56 PM

Here is a pic of Heavy Duty rear coils off of my '67 compared to a new set of Jeep TJ springs. The coils are noticeably thinner. Haven't had them completely bolted in yet but they seem to drop the truck about 3 inches during test fitting. Still waiting on a new set of retainers and hardware for final installation. got the springs at a jeep shop for ten bucks apiece.

mtburg71 · 11-30-2007, 12:09 PM

What did you pay for the rear springs?

danzka4u · 11-30-2007, 12:45 PM

I gave $20 for them but Im sure I could have got set for free if I would have put a little effort into it.

toomanytoyz · 11-30-2007, 12:20 PM

If you look a`t the 1st Pic you can see all the tire from top of Rim up & in the 2nd Pic it is just Top of Rim, Anyhow it Looks Great................

Rick

65 on 24's · 11-30-2007, 12:21 PM

did it bolt in or did you have to mod them any

danzka4u · 11-30-2007, 12:47 PM

they bolt right in but the spring it self is bit thiner so the hold downs may need a little motification.

**slepysal** · 11-30-2007, 02:03 PM

I got them for 5.00 +10.00 shiping off of e bay. look around for a 4wd shop that works on jeeps, chances are they will give them to you.
Oh and mine went in with no mods!

04Xrider · 11-30-2007, 06:09 PM

It looks great. I would like to do this to mine, but I would like a bit more drop in the front. How much did the front drop? Also what do you mean by 1 full coil plus 3 inches? I understand the one full coil, it is the plus 3 inches that is throwing me. Never mind, I figured it out.

danzka4u · 11-30-2007, 08:15 PM

You know I didn’t measure the drop in the front but I would say about 2 inches. I put the rear coils in first and the truck sat lower in the back. After I cut fronts it now sits with a slight rake. I did have to cut some off the stops in the front.

04Xrider · 11-30-2007, 09:18 PM

Quote:

Originally Posted by danzka4u

You know I didn’t measure the drop in the front but I would say about 2 inches. I put the rear coils in first and the truck sat lower in the back. After I cut fronts it now sits with a slight rake. I did have to cut some off the stops in the front.

OK thanks, and welcome to the board from Cookson OK.

Stepside65 · 11-30-2007, 08:58 PM

Nice truck. Looks good with the new drop.

Super73 · 11-30-2007, 10:48 PM

Are you using Jeep springs in the front? Wrangler, Cherokee, grand Cherokee??

I bought a set of front 6cyl cherokee springs and mine goes to the bumps (front). If I put 100lbs of lift it sits at the ride height I want so I think I'll build a spacer. I'm running a LS1/4L80E combo so I would think my front weight should be lighter than a SBC/TH350 combo.

Shaun

danzka4u · 12-01-2007, 11:59 AM

Not in the front just the back I cut the ones in the front.

fchava · 12-01-2007, 12:11 PM

Quote:

Originally Posted by danzka4u

Not in the front just the back I cut the ones in the front.

drop springs are so cheap and allow you to carry the same load as stock, why use jeep springs?

greenmtnboy · 12-02-2007, 12:18 PM

Quote:

Originally Posted by fchava

drop springs are so cheap and allow you to carry the same load as stock, why use jeep springs?

FREE vs cheap

We all know drop springs are relatively cheap, but free is better

.
As a WARNING FYI Here is mine with front springs cut TOO MUCH

I cut 2 full coils, then ended up with rubber spacers under the springs and some 1" bumpstops in place of the stock ones. In hindsite 1.5 coils would probably be ok.It rides like crap and bottoms out, but it was FREEEEE and allowed me to save my $ for '32 ford parts

I got a set of wrangler springs for the rear for free but have not gotten around to installing them yet.

AllenKarber · 02-18-2011, 12:06 PM

Quote:

Originally Posted by greenmtnboy

FREE vs cheap

We all know drop springs are relatively cheap, but free is better

.
As a WARNING FYI Here is mine with front springs cut TOO MUCH

I cut 2 full coils, then ended up with rubber spacers under the springs and some 1" bumpstops in place of the stock ones. In hindsite 1.5 coils would probably be ok.It rides like crap and bottoms out, but it was FREEEEE and allowed me to save my $ for '32 ford parts

I got a set of wrangler springs for the rear for free but have not gotten around to installing them yet.

I cut 2 coils off my stock springs,and boy was it low. It looked awesome,but the ride was pretty stiff,and I was always smashing my headers!

11-29-2007, 10:21 PM	#1
danzka4u Registered User Join Date: Oct 2007 Location: lompoc ca Posts: 17	Jeep Coil Spring Drop Hey guys Im new to yor site and I had been looking through the pages and saw a discution on lowering by using jeep coils in the rear and cutting the coils in the front. So I said what the heck lets do it. Here are a couple of photos of my 65. I cut one full coil plus 3 inches in the front I figured I can allways cut more buts its hard to add. before and after attached I hope Attached Images

11-29-2007, 10:30 PM	#2
toomanytoyz Luv the Crewcabs Join Date: Aug 2006 Location: Andrews, In. 46702 Posts: 4,097	Re: Jeep Coil Spring Drop Congrats & Welcome to The Board from Indiana.......... Truck Looks Real Good, What Coils did you use in the Rear?? Rick __________________ 55 Nomad 52 Willys Truck 67 Stepper 67 Fleet 68 Wrecker 68 Suburban 76 Crewcab 79 Gmc Dumptruck 84 Blazer 86 Crewcab Stepside 87 Iroc 89 GMC Plow Truck 91 Camaro Vert 96 Z71 Stepsde

11-30-2007, 10:38 AM	#3
danzka4u Registered User Join Date: Oct 2007 Location: lompoc ca Posts: 17	Re: Jeep Coil Spring Drop I used 98 wrangler springs. Now that I look at the pictures they don’t really do the drop justice it must be the different angle but the lowered the back about 4 inches.

11-30-2007, 12:42 PM	#5
danzka4u Registered User Join Date: Oct 2007 Location: lompoc ca Posts: 17	Re: Jeep Coil Spring Drop Thanks for the welcome. I dont realy put much in the bed. But I do pull a small trailer with my lawn equipment on it. I just have to take it a little easy over the bumps

02-12-2008, 04:27 AM	#7
ChiefRocka Hollister, CA. Join Date: Sep 2006 Location: Hollister, Ca. Posts: 6,147	Re: Jeep Coil Spring Drop Not so much that are the same diameter...they pigtail on both ends __________________ John What the Heck is that ?? CURRENT BUILDS: 62 BurbMaster Other Builds: My '63 C-10,LWB,CC,BBW '06 HD StrAight Axle Swap Father/Son '67 C-20, LQ9,4L80,Bagged,8-Lugger !!Good Friend Richard's Build AMERICAN CUSTOMS & CLASSICS (831) 630-1965 www.ACCHOLLISTER.com ACC on FACEBOOK "Rest in Peace, Mom & Dad ... I will see you again someday!"

07-21-2009, 04:56 PM	#10
Jblackie47803 Registered User Join Date: Apr 2009 Location: Terre Haute, IN Posts: 56	Re: Jeep Coil Spring Drop Here is a pic of Heavy Duty rear coils off of my '67 compared to a new set of Jeep TJ springs. The coils are noticeably thinner. Haven't had them completely bolted in yet but they seem to drop the truck about 3 inches during test fitting. Still waiting on a new set of retainers and hardware for final installation. got the springs at a jeep shop for ten bucks apiece.

11-30-2007, 12:09 PM	#11
mtburg71 Registered User Join Date: Nov 2007 Location: Temple, Texas Posts: 75	Re: Jeep Coil Spring Drop What did you pay for the rear springs? __________________ 1964 GMC SWBFS 2005 Dodge Magnum RT

11-30-2007, 12:45 PM	#12
danzka4u Registered User Join Date: Oct 2007 Location: lompoc ca Posts: 17	Re: Jeep Coil Spring Drop I gave $20 for them but Im sure I could have got set for free if I would have put a little effort into it.

11-30-2007, 12:20 PM	#13
toomanytoyz Luv the Crewcabs Join Date: Aug 2006 Location: Andrews, In. 46702 Posts: 4,097	Re: Jeep Coil Spring Drop If you look a`t the 1st Pic you can see all the tire from top of Rim up & in the 2nd Pic it is just Top of Rim, Anyhow it Looks Great................ Rick __________________ 55 Nomad 52 Willys Truck 67 Stepper 67 Fleet 68 Wrecker 68 Suburban 76 Crewcab 79 Gmc Dumptruck 84 Blazer 86 Crewcab Stepside 87 Iroc 89 GMC Plow Truck 91 Camaro Vert 96 Z71 Stepsde

11-30-2007, 12:21 PM	#14
65 on 24's Registered User Join Date: Sep 2006 Location: memphis tn, (nutbush) Posts: 160	Re: Jeep Coil Spring Drop did it bolt in or did you have to mod them any __________________ ridin big yo 5in cpp lowerin springs in back lowered 3in in front with cut springs for now 5 lug swap and disk in front 5 lug and disk in the rear with 3.23 gears mild 350/400heads 7547weiand intake 600 Edelbrock chrome block hugger headers 2 1/2 pipes in to a x pipes super 40 flows and turn downs turbo 350 with shift kit

11-30-2007, 12:47 PM	#15
danzka4u Registered User Join Date: Oct 2007 Location: lompoc ca Posts: 17	Re: Jeep Coil Spring Drop they bolt right in but the spring it self is bit thiner so the hold downs may need a little motification.

11-30-2007, 02:03 PM	#16
slepysal Registered User Join Date: Oct 2006 Location: San Jose NOR*CAL Posts: 3,079	Re: Jeep Coil Spring Drop I got them for 5.00 +10.00 shiping off of e bay. look around for a 4wd shop that works on jeeps, chances are they will give them to you. Oh and mine went in with no mods! __________________ 1960 Apache long bed fleet L6 250 Clifford intake 2 bbl carb. Langdon cast headers with dual exhaust and bellflower tips. T-5 5 speed, power steering and power disc brakes. "Over, Around or through it... "

11-30-2007, 06:09 PM	#17
04Xrider Registered thread killer Join Date: Nov 2006 Location: Cookson, OK. Posts: 349	Re: Jeep Coil Spring Drop It looks great. I would like to do this to mine, but I would like a bit more drop in the front. How much did the front drop? Also what do you mean by 1 full coil plus 3 inches? I understand the one full coil, it is the plus 3 inches that is throwing me. Never mind, I figured it out. __________________ !966 stepside, 350 SB, ZZ-4 roller, Crane roller rockers, 0.030 flat tops, airgap intake, 750 Holley, stainless steel headers, edelbrock SDT mufflers, Mark 8 elec fan, 700R-4, column shift Last edited by 04Xrider; 11-30-2007 at 06:40 PM.

11-30-2007, 08:15 PM	#18
danzka4u Registered User Join Date: Oct 2007 Location: lompoc ca Posts: 17	Re: Jeep Coil Spring Drop You know I didn’t measure the drop in the front but I would say about 2 inches. I put the rear coils in first and the truck sat lower in the back. After I cut fronts it now sits with a slight rake. I did have to cut some off the stops in the front.

11-30-2007, 08:58 PM	#20
Stepside65 Still Truckless! Join Date: Jul 2007 Location: Valrico, Florida Posts: 3,166	Re: Jeep Coil Spring Drop Nice truck. Looks good with the new drop. __________________ ~James Truckless 2009 Hyundai Sonata<~~Wife's sedanomatic 1997 Nissan Pickup Father-in-law's tonka toy I am forced to drive Founder of The 60-66 Club Tutor Et Ultor



Register or Log In To remove these advertisements.

11-30-2007, 10:48 PM	#21
Super73 Registered User Join Date: Nov 2007 Location: Bay Area, Ca Posts: 2,841	Re: Jeep Coil Spring Drop Are you using Jeep springs in the front? Wrangler, Cherokee, grand Cherokee?? I bought a set of front 6cyl cherokee springs and mine goes to the bumps (front). If I put 100lbs of lift it sits at the ride height I want so I think I'll build a spacer. I'm running a LS1/4L80E combo so I would think my front weight should be lighter than a SBC/TH350 combo. Shaun

12-01-2007, 11:59 AM	#22
danzka4u Registered User Join Date: Oct 2007 Location: lompoc ca Posts: 17	Re: Jeep Coil Spring Drop Not in the front just the back I cut the ones in the front.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

Register or Log In To remove these advertisements.