The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1960 - 1966 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 10-11-2017, 09:08 PM   #1
67pete300
Registered User
 
Join Date: Mar 2008
Location: Burke, VA
Posts: 114
Need help with lower ball joint

Trying to get started with my disc brake upgrade and for the life of me can't get the lower ball joint broken loose. I've been pounding on it mercilessly and the two pickle forks I have can't seem to get any purchase on anything solid.

Everything is being replaced (except the control arm.) Can I just remove the whole lower control arm and destructively remove the ball joint from the bottom?

Suggestions welcome. Never done this before. And yes I've searched hi and low for answers. I haven't tried renting or buying a special ball joint separating tool yet. But beating on the spindle and pickle fork seem to be common solutions that work for others...
Attached Images
  
67pete300 is offline   Reply With Quote
Old 10-11-2017, 09:31 PM   #2
ezz16
Registered User
 
Join Date: Oct 2015
Location: Landis NC
Posts: 44
Re: Need help with lower ball joint

Went through the same thing even made a spreader bolt to apply more pressure. but every one I know said get a bigger hammer I did and about 8 solid hits later it dropped. are you hitting it directly with that big hammer?
ezz16 is offline   Reply With Quote
Old 10-11-2017, 11:52 PM   #3
grubsster
Registered User
 
grubsster's Avatar
 
Join Date: Sep 2011
Location: N.C.
Posts: 133
Re: Need help with lower ball joint

I also had a hard time breaking my lower ball joint loose. The fork was going all the way in. What I did was take a 1 inch open end wrench and wedge the pickle fork in between it and the control arm. A few good wacks with the 3 pound sledge and it popped loose. Hope this helps.
grubsster is offline   Reply With Quote
Old 10-16-2017, 06:23 AM   #4
luvbowties
Registered User
 
luvbowties's Avatar
 
Join Date: Feb 2009
Location: southeasternfoothillsofusa
Posts: 1,557
Cool Re: Need help with lower ball joint

In top picture, is weight of lower a-frame supported by jack? If so, remove jack(jack up elsewhere to let a-frame hang loosely in the air) and wham w/big hammer, at 90-degrees directly beside where b-jnt goes thru the hole. This way, spring tension will "be on your side" & help you more as you hit.
HTH,
sam

Last edited by luvbowties; 10-16-2017 at 06:28 AM. Reason: sp
luvbowties is offline   Reply With Quote
Old 10-16-2017, 10:00 PM   #5
rvrfoot
Registered User
 
Join Date: Oct 2016
Location: san bernardino ca
Posts: 1,611
Re: Need help with lower ball joint

Lower the jack put a load on it. Then hit it with a hammer.
rvrfoot is offline   Reply With Quote
Old 10-16-2017, 10:29 PM   #6
67pete300
Registered User
 
Join Date: Mar 2008
Location: Burke, VA
Posts: 114
Re: Need help with lower ball joint

Thanks for the feedback. I finally managed to pop it loose with. New 4 lb hammer that I could swing better than the big sledge and the perfect angle on the pickle fork.

Got the control arm shafts out thanks to my buddy who had the right sockets.

Next challenge is upper ball joint rivets...
Attached Images
 
67pete300 is offline   Reply With Quote
Old 10-16-2017, 11:04 PM   #7
rvrfoot
Registered User
 
Join Date: Oct 2016
Location: san bernardino ca
Posts: 1,611
Re: Need help with lower ball joint

Grind them off.
rvrfoot is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:48 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com