|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
04-08-2017, 10:29 AM
|
#1 |
|
Senior Member
 
Join Date: Dec 2009
Location: Chester,California
Posts: 5,618
|
Need ID help Chry/Autolite distributor
Does anyone know what this fits? Where can I get info? I have searched Internet!
__________________
1977 Chevrolet K10 SWB Project 350/4spd/np205 1977 Chevrolet K20 LWB 350/350/203 1991 4Runner 22RE 5 SPD Yanmar Tractor 3 Cyl Diesel |
|
|
|
04-08-2017, 10:31 AM
|
#2 |
|
Senior Member
Join Date: Dec 2009
Location: Chester,California
Posts: 5,618
|
Re: Need ID help Chry/Autolite distributor
Chrysler 1664956
Autolite 1BM-4001-B 1OU IBP1
__________________
1977 Chevrolet K10 SWB Project 350/4spd/np205 1977 Chevrolet K20 LWB 350/350/203 1991 4Runner 22RE 5 SPD Yanmar Tractor 3 Cyl Diesel |
|
|
|
|
04-08-2017, 10:32 AM
|
#3 |
|
Senior Member
Join Date: Dec 2009
Location: Chester,California
Posts: 5,618
|
Re: Need ID help Chry/Autolite distributor
Dual point?
__________________
1977 Chevrolet K10 SWB Project 350/4spd/np205 1977 Chevrolet K20 LWB 350/350/203 1991 4Runner 22RE 5 SPD Yanmar Tractor 3 Cyl Diesel |
|
|
|
|
04-10-2017, 03:31 PM
|
#4 |
|
Registered User
Join Date: May 2010
Location: Lawrenceville, Ga
Posts: 2,640
|
Re: Need ID help Chry/Autolite distributor
I don't see any way to drive it. Does the bottom of the shaft have a hex shaped hole in it? Old Ford distributors were driven by a hex shaped shaft so that's possibly what it is.
|
|
|
|
|
04-10-2017, 10:28 PM
|
#5 |
|
Registered User
Join Date: Apr 2009
Location: Carrying Place, Ontario
Posts: 48
|
Re: Need ID help Chry/Autolite distributor
looks very similar to the one that is my sons 54 Dodge with a flathead 6
__________________
Dave 
|
|
|
|
|
04-11-2017, 01:34 AM
|
#6 |
|
Registered User
Join Date: Nov 2010
Location: cape may nj
Posts: 94
|
Re: Need ID help Chry/Autolite distributor
big block mopar
|
|
|
|
|
04-11-2017, 09:45 PM
|
#7 |
|
Registered User
Join Date: May 2010
Location: Lawrenceville, Ga
Posts: 2,640
|
Re: Need ID help Chry/Autolite distributor
Mopar distributors for V8 engines have a flat tab on the bottom of the shaft that engages a slot in the drive gear. Slant six engines have a plastic gear on the shaft so there would be a hole for the roll pin if this was a slant six distributor. I don't remember what the old mopar flat head sixes used. I don't see any way for a gear to attach to the shaft on the distributor pictured so I thought it might be from an old Ford six cylinder engine. They were driven by a hex shaped shaft that that stuck into the distributor shaft.
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
