The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Paint & Bodywork

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 03-13-2017, 08:23 PM   #1
Dave0
Registered User
 
Join Date: Apr 2016
Location: Brighton IL
Posts: 142
Faux paint step by step

A couple people asked me to show them how I was reproducing the patina on my truck... I figured this was the better forum to put it in... There are some examples on this page of my build thread http://67-72chevytrucks.com/vboard/s...=702899&page=7

Keep in mind, so far I am only doing small areas. But will do a couple new doors and a hood later on... I will start off with a epoxy primed part for "actual" rust protection...

Pic 1, the colors I am using. All Krylon.

Pic 2, a primed card, using the same color primmer on the truck.

Pic 3, template and color for a rust spot, say a body line.

Pic 4, the rust spot

Pic 5, another color and a smaller slit to add some depth to the rust spot.
Attached Images
    
Dave0 is offline   Reply With Quote
Old 03-13-2017, 08:24 PM   #2
Dave0
Registered User
 
Join Date: Apr 2016
Location: Brighton IL
Posts: 142
Re: Faux paint step by step

Pic 6, rust spot

Pic 7, gold texture paint drizzled on

Pic 8, rust colored primer

Pic 9, red paint

Pic 10, sanding thru some layers, exposing the multiple colors under the red
Attached Images
     

Last edited by Dave0; 03-13-2017 at 08:30 PM.
Dave0 is offline   Reply With Quote
Old 03-13-2017, 08:24 PM   #3
Dave0
Registered User
 
Join Date: Apr 2016
Location: Brighton IL
Posts: 142
Re: Faux paint step by step

Pic 11, laying on the step

Pic, 12 behind the cab

Pic 13, some cutouts in cardboard I use. For different effects....Gives you a better idea of the colors used too
Attached Images
   

Last edited by Dave0; 03-13-2017 at 08:47 PM.
Dave0 is offline   Reply With Quote
Old 03-13-2017, 08:25 PM   #4
Dave0
Registered User
 
Join Date: Apr 2016
Location: Brighton IL
Posts: 142
Re: Faux paint step by step

I ended up spraying some more dark gray primer on the card (to "hide" some of the red) to match other areas of the truck. Every panel is different.

I already used some of these techniques in the first pic. I patched in the fuel filler location and spray bombed it... That rusty looking spot is the body line of the cab corner... Cheers!
Attached Images
     

Last edited by Dave0; 03-13-2017 at 08:46 PM.
Dave0 is offline   Reply With Quote
Old 03-13-2017, 08:48 PM   #5
Dave0
Registered User
 
Join Date: Apr 2016
Location: Brighton IL
Posts: 142
Re: Faux paint step by step

Here is a spot in the roof where I welded a hole shut. I intentionally sanded a line in it and left a slight low spot in it. I used the dark gray primer and a another color that matched the rust... Is it spotless? No but it will blend in once its cleared...
Attached Images
  

Last edited by Dave0; 03-13-2017 at 08:59 PM.
Dave0 is offline   Reply With Quote
Old 03-13-2017, 09:00 PM   #6
Dave0
Registered User
 
Join Date: Apr 2016
Location: Brighton IL
Posts: 142
Re: Faux paint step by step

RT Bed corner and fuel filler patches
Attached Images
    

Last edited by Dave0; 03-13-2017 at 09:07 PM.
Dave0 is offline   Reply With Quote
Old 03-14-2017, 04:07 PM   #7
bs46488
Registered User
 
Join Date: May 2014
Location: San Diego, CA
Posts: 333
Re: Faux paint step by step

That's pretty cool to see the before and after shots of the repairs.

Just curious, how exactly do you "drizzle" rattle can paints?
__________________
Project Engine Stand 1972 SWB conversion: http://67-72chevytrucks.com/vboard/s...d.php?t=673914

1970 Nova: http://67-72chevytrucks.com/vboard/s...d.php?t=708161
bs46488 is offline   Reply With Quote
Old 03-14-2017, 04:10 PM   #8
Dave0
Registered User
 
Join Date: Apr 2016
Location: Brighton IL
Posts: 142
Re: Faux paint step by step

Stuck the right size piece of copper wire in the end of the nozzle...Play with different sizes
Dave0 is offline   Reply With Quote
Old 03-24-2017, 02:00 AM   #9
Az. Hank
Registered User
 
Az. Hank's Avatar
 
Join Date: Feb 2009
Location: Fort Mohave, Arizona
Posts: 186
Re: Faux paint step by step

That is one of the better "Patina" jobs I've seen. Thanks for the how to..
__________________
My 55 Build 55 C-4
Az. Hank is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:23 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Copyright 1997-2013 67-72chevytrucks.com