Emblem Clips - The 1947 - Present Chevrolet & GMC Truck Message Board Network

AHowe88 · 09-26-2013, 11:58 AM

I'm familiar with the speed nuts that attach to the inside of the panel you are mounting your emblem on, like these:
http://www.summitracing.com/parts/oer-11501047

But what I was removing my CST emblem to get the truck painted, it had a sleeve clip, something like this: http://www.ebay.com/itm/Buick-Chevy-...item20ba368b9d

The ebay clips are too small to fit the shafts of my emblems. Does anyone know where I can get a larger set? It would make mounting the fender emblems much easier with a set of these.

jaros44sr · 09-26-2013, 01:43 PM

What size is the pin on the emblem and hole in your fender, i have some retainers laying around

AHowe88 · 09-26-2013, 02:02 PM

Quote:

Originally Posted by jaros44sr

What size is the pin on the emblem and hole in your fender, i have some retainers laying around

Looks like the emblem studs are 3/16". Not sure about the hole, the truck is off getting painted now. If you think you might have those clips, let me know how many you have and what you want for them.

Thanks!

jaros44sr · 09-27-2013, 12:08 PM

Studs on the custom emblem measure 1/8" (.125); and these fastners seem to fit them. Outside OD measure 3/16". I see what you mean by not using the nuts, hard access. Usually this type of fastner, the stud would not have any threads, like our emblems do, but you could file them down

LMK, if these will help you out, they were used on old english sports cars, so i would have to dig deeper if you need more....the only thing i would worry about is scratching your new paint with the push in fastner. If you use the OEM fastner you can use a small o ring in the nut, and then it wont scratch your paint as you tighten it down. Thats were the rust would start, with bare metal

20130927_115847 by jarosaj, on Flickr

AHowe88 · 09-27-2013, 01:34 PM

I ended up buying some on Ebay that I hope will work. I'll give them a try when they get here, if they don't work I might take up up on your generous offer. Thanks!

jaros44sr · 09-27-2013, 02:01 PM

Quote:

Originally Posted by AHowe88

I ended up buying some on Ebay that I hope will work. I'll give them a try when they get here, if they don't work I might take up up on your generous offer. Thanks!

What was the name of the fastner, barrel nuts?

AHowe88 · 09-27-2013, 02:25 PM

Quote:

Originally Posted by jaros44sr

What was the name of the fastner, barrel nuts?

Tubular nuts. These look like what was used to secure my CST emblem to the door.

http://www.ebay.com/itm/400219662640...S:3160&vxp=mtr

**pound41** · 09-28-2013, 12:09 AM

You can find those in most help section at the auto parts store

09-26-2013, 11:58 AM	#1
AHowe88 Registered User Join Date: Jul 2013 Location: Metrowest, MA Posts: 254	Emblem Clips I'm familiar with the speed nuts that attach to the inside of the panel you are mounting your emblem on, like these: http://www.summitracing.com/parts/oer-11501047 But what I was removing my CST emblem to get the truck painted, it had a sleeve clip, something like this: http://www.ebay.com/itm/Buick-Chevy-...item20ba368b9d The ebay clips are too small to fit the shafts of my emblems. Does anyone know where I can get a larger set? It would make mounting the fender emblems much easier with a set of these.

09-26-2013, 01:43 PM	#2
jaros44sr Registered User Join Date: May 2006 Location: Philadelphia, Pa. 19454 Posts: 9,421	Re: Emblem Clips What size is the pin on the emblem and hole in your fender, i have some retainers laying around __________________ Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim

09-27-2013, 12:08 PM	#4
jaros44sr Registered User Join Date: May 2006 Location: Philadelphia, Pa. 19454 Posts: 9,421	Re: Emblem Clips Studs on the custom emblem measure 1/8" (.125); and these fastners seem to fit them. Outside OD measure 3/16". I see what you mean by not using the nuts, hard access. Usually this type of fastner, the stud would not have any threads, like our emblems do, but you could file them down LMK, if these will help you out, they were used on old english sports cars, so i would have to dig deeper if you need more....the only thing i would worry about is scratching your new paint with the push in fastner. If you use the OEM fastner you can use a small o ring in the nut, and then it wont scratch your paint as you tighten it down. Thats were the rust would start, with bare metal 20130927_115847 by jarosaj, on Flickr __________________ Semper Fi...Uncle Sam, you da man All parts offered to help are free, unless otherwise noted Dont try this stuff in my build thread, unless you have 55 years of mechanical OTJ training SAFETY FIRST AS usual, off topic They say your mind goes second, can't remember the first Jim Last edited by jaros44sr; 09-27-2013 at 12:18 PM.

09-27-2013, 01:34 PM	#5
AHowe88 Registered User Join Date: Jul 2013 Location: Metrowest, MA Posts: 254	Re: Emblem Clips I ended up buying some on Ebay that I hope will work. I'll give them a try when they get here, if they don't work I might take up up on your generous offer. Thanks!

09-28-2013, 12:09 AM	#8
pound41 Registered User Join Date: Dec 2002 Location: Northern Virginia Posts: 1,267	Re: Emblem Clips You can find those in most help section at the auto parts store



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.