Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
11-13-2024, 05:57 PM | #1 |
Registered User
Join Date: Dec 2012
Location: Fort Thomas, KY
Posts: 300
|
76 C10 Brake Bleeding Issues
Helping a young man bleed the brakes on his 76 C10.
He has replaced the following: Master Cylinder - bench bled Proportioning Valve - w/ centering tool inserted Front Calipers Rear Cylinders and pads brakes lines to rear, new T-Hose, and rear axle lines Brakes lines to Prop valve When trying to bleed the brakes, the pedal is soft for the first half of the stroke and then gets firm. Opening the rear bleeders does not allow the pedal to go to the floor. Opening the front bleeders does. We are getting good flow through all bleeders. The rear brakes are not building pressure no matter what and the pedal never gets hard once you pump it a few times. The rear wheels are not braking but the fronts are. One thing to note is that the E-brake is not working. Does this have any affect on bleeding? Any recommendations on how to bleed or what might be causing the soft pedal would be appreciated.
__________________
1972 GMC 1500 Super Custom, 383 Stoker, TH350 Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=592157 Engine Thread http://67-72chevytrucks.com/vboard/s...d.php?t=592233 |
11-13-2024, 06:58 PM | #2 |
Registered User
Join Date: Oct 2013
Location: Maine
Posts: 2,371
|
Re: 76 C10 Brake Bleeding Issues
Prop valve has an issue but I have no idea why. My truck just blew a line so I pinched it until I can replace it. My pedal sounds like it's working like yours. My brake light isn't on so I was hoping my prop valve is still centered/ I still have fluid flowing to the rear brakes also. So you have fluid going to the rear brakes but no actual braking?
__________________
76 Chevy K20 76 GMC K15 77 Chevy C10 77 Chevy K10 |
11-13-2024, 07:54 PM | #3 |
Registered User
Join Date: Dec 2012
Location: Fort Thomas, KY
Posts: 300
|
Re: 76 C10 Brake Bleeding Issues
Yes, fluid is flowing to the rears but the cylinders are not braking. They are expanding, but no pressure.
The prop valve is centered with centering tool. Does the e-brake cable not working have any impact?
__________________
1972 GMC 1500 Super Custom, 383 Stoker, TH350 Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=592157 Engine Thread http://67-72chevytrucks.com/vboard/s...d.php?t=592233 |
11-13-2024, 07:56 PM | #4 |
Registered User
Join Date: Dec 2012
Location: Fort Thomas, KY
Posts: 300
|
Re: 76 C10 Brake Bleeding Issues
The other noticeable thing is that the hose from the rear brake line makes a bend/loop upwards till it reaches the axle. Can air get trapped in there while bleeding?
__________________
1972 GMC 1500 Super Custom, 383 Stoker, TH350 Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=592157 Engine Thread http://67-72chevytrucks.com/vboard/s...d.php?t=592233 |
11-13-2024, 08:06 PM | #5 |
Registered User
Join Date: Aug 2009
Location: Bowser
Posts: 13,727
|
Re: 76 C10 Brake Bleeding Issues
What’s the masters bore?
Did you check they are the same old to new? |
11-14-2024, 10:17 AM | #6 |
Registered User
Join Date: Aug 2012
Location: Oklahoma City, OK
Posts: 2,599
|
Re: 76 C10 Brake Bleeding Issues
e-brake not working should have no impact on the hydraulic brake system. Not saying impossible but unlikely.
If you installed new rear drums, you will need to do an initial adjust on the rear shoes. Possible they are so far from the drums that there isn't enough movement from the cylinders to get braking action. Once you get the rears close, the traditional way to do the final adjust is to go in reverse about 10mph and stomp on the brakes and let the auto-adjust do its thing. Repeat several times. Make sure the rear shoes are installed correctly. IIRC - short shoe goes to the front. Last edited by Dead Parrot; 11-14-2024 at 10:22 AM. |
11-14-2024, 11:27 AM | #7 |
Registered User
Join Date: Dec 2012
Location: Fort Thomas, KY
Posts: 300
|
Re: 76 C10 Brake Bleeding Issues
Thanks for the replies.
We have installed the pads correctly and adjusted them out as far as we could and still be able to get the new drums on. These new drums don't have the adjuster windows in them! The vehicle is not driveable right now so we can't do the backup adjusting. The master cylinder appears to be the same as what was removed. Hard to tell without disassembly. Still wondering if there is an air pocket in the hose that goes from the rear line to the axle T-fitting. The hose actually makes a loop up from the frame line and then back down to the axle. Gonna disconnect the hose from the T-fitting and point it up and see if we bleed air out of it. It shouldn't be this difficult to bleed brakes!!!
__________________
1972 GMC 1500 Super Custom, 383 Stoker, TH350 Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=592157 Engine Thread http://67-72chevytrucks.com/vboard/s...d.php?t=592233 |
11-14-2024, 12:39 PM | #8 |
Registered User
Join Date: Aug 2009
Location: Bowser
Posts: 13,727
|
Re: 76 C10 Brake Bleeding Issues
Are we to assume he has a factory booster and pedal assembly?
|
11-14-2024, 02:27 PM | #9 |
Registered User
Join Date: Aug 2012
Location: Oklahoma City, OK
Posts: 2,599
|
Re: 76 C10 Brake Bleeding Issues
It shouldn't be but sometimes can be difficult. Frustration avoidance tip - make sure you keep the MC mostly full of fluid.
Even a new MC can be bad. If you eliminate everything else, try a different new MC. The adjuster window should be in the backing plate. Not all have one. Sometimes it will have one but it isn't knocked out. 2nd the checking for flow and air from the rear hose. |
11-14-2024, 03:10 PM | #10 |
Registered User
Join Date: Dec 2012
Location: Fort Thomas, KY
Posts: 300
|
Re: 76 C10 Brake Bleeding Issues
Yes, as far as well can tell if is original.
When we originally started bleeding the system after replacing lines, prop valve and wheel cylinders, we had the soft pedal issue. Figured it was the master cylinder and then decided to replace it. Still getting the same soft pedal issue with the new master cylinder. We'll try bleeding the T-fitting tomorrow once it stops raining.
__________________
1972 GMC 1500 Super Custom, 383 Stoker, TH350 Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=592157 Engine Thread http://67-72chevytrucks.com/vboard/s...d.php?t=592233 |
11-14-2024, 05:26 PM | #11 |
Registered User
Join Date: Aug 2009
Location: Bowser
Posts: 13,727
|
Re: 76 C10 Brake Bleeding Issues
I’d be inclined to suspect the prop valve.
Are the lines to it from the master the same as original? |
11-14-2024, 06:44 PM | #12 |
Registered User
Join Date: Dec 2012
Location: Fort Thomas, KY
Posts: 300
|
Re: 76 C10 Brake Bleeding Issues
Yeah, we replaced the lines to the prop valve with like original. All lines came from Inline Tube.
We are on our second prop valve. Inserted the centering pin in the valve before installing on the cross member. Had to modify the pin to insure it seated all the way down. The plastic centering pin should have thread relief at the start to allow it to thread all the way down.
__________________
1972 GMC 1500 Super Custom, 383 Stoker, TH350 Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=592157 Engine Thread http://67-72chevytrucks.com/vboard/s...d.php?t=592233 |
11-14-2024, 06:55 PM | #13 |
Registered User
Join Date: Aug 2009
Location: Bowser
Posts: 13,727
|
Re: 76 C10 Brake Bleeding Issues
Maybe you shouldn’t modify the pin.
|
11-14-2024, 07:17 PM | #14 |
Registered User
Join Date: Dec 2012
Location: Fort Thomas, KY
Posts: 300
|
Re: 76 C10 Brake Bleeding Issues
The pin in the tool was not going all the way down into the bore. We modified the threads (not the pin) so that it would screw all the way down and prevent the piston from moving.
__________________
1972 GMC 1500 Super Custom, 383 Stoker, TH350 Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=592157 Engine Thread http://67-72chevytrucks.com/vboard/s...d.php?t=592233 |
11-15-2024, 03:20 AM | #15 |
Senior Member
Join Date: Dec 2018
Location: yamhill OR
Posts: 905
|
Re: 76 C10 Brake Bleeding Issues
Like Dead Parrot said, the adjuster window is in the backing plate not in the the drum on these.
What bleeding method are you using?
__________________
1965 chevy c20 292 4speed http://67-72chevytrucks.com/vboard/s...d.php?t=777601 1976 chevy c10 250 4speed http://www.67-72chevytrucks.com/vboa...d.php?t=787037 1978 chevy c20 350 4speed 1998 chevy c1500 4.3L 5speed 2002 Chevy s10 4.3L auto 4x4 Plus a Mercury & some Fords... To many projects! |
11-15-2024, 02:12 PM | #16 |
Registered User
Join Date: Dec 2012
Location: Fort Thomas, KY
Posts: 300
|
Re: 76 C10 Brake Bleeding Issues
Doing the two person bleed: press pedal and open bleeder fitting. Start in rear and then do the fronts.
While doing this, we noticed that the for the front, the pedal goes to the floor while bleeding, but the rears do not. And the pedal never gets hard at the top. Stays soft until about half way down.
__________________
1972 GMC 1500 Super Custom, 383 Stoker, TH350 Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=592157 Engine Thread http://67-72chevytrucks.com/vboard/s...d.php?t=592233 |
11-16-2024, 08:26 PM | #17 |
Registered User
Join Date: Oct 2013
Location: Maine
Posts: 2,371
|
Re: 76 C10 Brake Bleeding Issues
Well, the prop valve still has an issue but I'm not sure what to do with it. I have never had a centering tool or used a centering tool. When I have a prop valve blocking pressure to the rear I first take it for a short easy slow ride and stomp on the brake pedal mercilessly. I do it in drive and reverse. After a while it will usually come out of it. One time it wouldn't come out of it and I used a trick I learned on the net. I just opened a bleeder on the front brakes and give it a few pumps and the prop piston will move the other way. You have to be kinda careful not to go all the way to the floor because you can damage an internal seal in the master cylinder.
If I wouldn't have blown a brake line in my GF's Jeep I would be fixing my truck rear brake line this weekend and have a better feel for what you are going through. The very squeaky wheel gets the grease this weekend. My truck pedal has no resistance for the first half of travel then it is very firm. Once I fix the brake line or maybe two on that Jeep I won't be in the mood to fix my truck this weekend. That's the only food for thought that I can add at this time.
__________________
76 Chevy K20 76 GMC K15 77 Chevy C10 77 Chevy K10 |
11-17-2024, 04:45 PM | #18 |
Registered User
Join Date: Dec 2012
Location: Fort Thomas, KY
Posts: 300
|
Re: 76 C10 Brake Bleeding Issues
So, we finally got the brakes bled with a hard pedal.
The new hose assembly from the rear line to the axle lines was slipping on the crimped fitting at the tee. We could turn the hose, even though the end fitting was tight on the tee fitting. We replaced the hose and made sure that the air would purge out of it by holding level to allow all the air to pass through and then bled the system. Thanks for all the suggestions but it turned out a faulty replacement part was the culprit.
__________________
1972 GMC 1500 Super Custom, 383 Stoker, TH350 Build Thread http://67-72chevytrucks.com/vboard/s...d.php?t=592157 Engine Thread http://67-72chevytrucks.com/vboard/s...d.php?t=592233 |
Bookmarks |
Thread Tools | |
Display Modes | |
|
|