what engine and engine frame mounts in a 75-79 clipped 55-57 did you use - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**idbeast** · 11-23-2016, 12:24 AM

What engine and engine frame mounts in a 75-79 Nova/Camaro clipped 55-57 truck did you use for a '78 350/383/400? Also what transmission cross member? I've spent 3 days searching but haven't stumbled across an answer!

59chev · 11-23-2016, 01:29 AM

Depends how the Camaro clip is mounted.

If it is blended into the truck framerails, the engine would sit too low if the stock camaro mounts are used, so most guys buy a set of universal stand type mounts like is offered by Welder Series or Speedway or Summit.

The other method of doing a Camaro clip, where the truck frame is stacked on top of the camaro subframe mounts, gives the frame a bit of a Z of a couple of inches so stock Camaro engine mounts are often used.

For a transmission crossmember, a universal one like is offered from CPP and other vendors is often used.

**idbeast** · 11-23-2016, 03:34 PM

I read somewhere in a post that chevelle motor /frame mounts were 1 inch taller then camaro/nova mounts, is this true?
See what happens when you do a search, it really messes with your mind!

mr48chev · 11-23-2016, 11:16 PM

I'm not sure on that one, here is what one of my buddies did on one he put together.
[URL=http://s173.photobucket.com/user/mr48chev/media/Tri%205%20pu%20subframe/3-14-09003.jpg.html]

[/

It looks like he used some plate steel to raise it up a bit.

On engine swaps I have done I finally figured out that it is a lot simpler to mount the trans where it needs to be and then figure out what to do with the front mounts to get the engine sitting where it should. You usually have some room to play with at the front as far as up and down go but most of the time the output shaft on the trans wants to be real close to the same spot that the original one was in no matter what front suspension you have.

**idbeast** · 11-24-2016, 10:00 PM

Thank you Mr48chev!

Dave0 · 11-25-2016, 03:06 PM

I made half and bought half...See post 35 here http://67-72chevytrucks.com/vboard/s...=702899&page=2

Post 73 for the trans x member that mounts in original spot.... http://67-72chevytrucks.com/vboard/s...=702899&page=3

As well as some useful info from Kim57 on that same page....

11-23-2016, 12:24 AM	#1
idbeast Senior Member Join Date: Oct 2016 Location: Olympia, WA Posts: 520	what engine and engine frame mounts in a 75-79 clipped 55-57 did you use What engine and engine frame mounts in a 75-79 Nova/Camaro clipped 55-57 truck did you use for a '78 350/383/400? Also what transmission cross member? I've spent 3 days searching but haven't stumbled across an answer!

11-23-2016, 01:29 AM	#2
59chev Registered User Join Date: Apr 2007 Location: Calgary, Alberta Posts: 441	Re: what engine and engine frame mounts in a 75-79 clipped 55-57 did you use Depends how the Camaro clip is mounted. If it is blended into the truck framerails, the engine would sit too low if the stock camaro mounts are used, so most guys buy a set of universal stand type mounts like is offered by Welder Series or Speedway or Summit. The other method of doing a Camaro clip, where the truck frame is stacked on top of the camaro subframe mounts, gives the frame a bit of a Z of a couple of inches so stock Camaro engine mounts are often used. For a transmission crossmember, a universal one like is offered from CPP and other vendors is often used. __________________ My Build Thread: 59 Apache - Lifelong obsession http://67-72chevytrucks.com/vboard/showthread.php?t=622133"]59 Apache - Lifelong obsession

11-23-2016, 03:34 PM	#3
idbeast Senior Member Join Date: Oct 2016 Location: Olympia, WA Posts: 520	Re: what engine and engine frame mounts in a 75-79 clipped 55-57 did you use I read somewhere in a post that chevelle motor /frame mounts were 1 inch taller then camaro/nova mounts, is this true? See what happens when you do a search, it really messes with your mind!

11-23-2016, 11:16 PM	#4
mr48chev Registered User Join Date: Jul 2007 Location: Toppenish, WA Posts: 15,286	Re: what engine and engine frame mounts in a 75-79 clipped 55-57 did you use I'm not sure on that one, here is what one of my buddies did on one he put together. [URL=http://s173.photobucket.com/user/mr48chev/media/Tri%205%20pu%20subframe/3-14-09003.jpg.html][/ It looks like he used some plate steel to raise it up a bit. On engine swaps I have done I finally figured out that it is a lot simpler to mount the trans where it needs to be and then figure out what to do with the front mounts to get the engine sitting where it should. You usually have some room to play with at the front as far as up and down go but most of the time the output shaft on the trans wants to be real close to the same spot that the original one was in no matter what front suspension you have. __________________ Founding member of the too many projects, too little time and money club. My ongoing truck projects: 48 Chev 3100 that will run a 292 Six. 71 GMC 2500 that is getting a Cad 500 transplant. 77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.

11-24-2016, 10:00 PM	#5
idbeast Senior Member Join Date: Oct 2016 Location: Olympia, WA Posts: 520	Re: what engine and engine frame mounts in a 75-79 clipped 55-57 did you use Thank you Mr48chev!

11-25-2016, 03:06 PM	#6
Dave0 Registered User Join Date: Apr 2016 Location: Brighton IL Posts: 209	Re: what engine and engine frame mounts in a 75-79 clipped 55-57 did you use I made half and bought half...See post 35 here http://67-72chevytrucks.com/vboard/s...=702899&page=2 Post 73 for the trans x member that mounts in original spot.... http://67-72chevytrucks.com/vboard/s...=702899&page=3 As well as some useful info from Kim57 on that same page....



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.