What did you do to your truck today? Chapter II - Page 12 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

*Fitz* · 02-28-2014, 01:37 PM

Fabricated and installed a polished stainless steel radiator cover.

67Slider · 02-28-2014, 02:08 PM

Looks good Fitz! How long did it take you?

*Fitz* · 02-28-2014, 04:47 PM

Quote:

Originally Posted by 67Slider

Looks good Fitz! How long did it take you?

About four hours, starting with a 12 X 36 sheet of 18 ga stainless. Use Aluminum if you don't have a set of carbide sheet metal cutters for the holes, though. Stainless is TOUGH on drill bits and sheet metal cutters.

**Mike_The_Grad** · 03-01-2014, 08:29 AM

Ready to be put back into service...but, I had a smidgen of forethought as far as spark plug wiring is concerned. Im looking for a "clean" appearance. Considering i just painted the engine and frame. I have hedman long tube headers, already piped to fit, and it seems I have a routing issue with #5 & #6 plugs. the primary tubes from #1 & #2 run so close to the plugs that the wire looms I have won't allow the boot (taylor cut to fit red wires with 90° boot) any clearance at all, were talking 1/8" max. I can only imagine doing this if it was in the truck! So I'm faced with a dilemma. I have a lot of "bling" on top, and I just picked up the wires. I would really like to show off both. Different headers are not out of the question, nor is different wiring, considering I haven't cut any wires yet. Any input is well received!...

*Fitz* · 03-01-2014, 09:56 AM

I avoided that problem with my headers by using 45 degree plug boots and the GM wire looms. Should work on yours too.

**Mike_The_Grad** · 03-01-2014, 01:44 PM

Thanx Fitz. I thought of 45° boots also.But I think I have a solution.I'm gonna try header wrap and just go a little beyond the boots. Plus side is I won't have to wire wheel and paint the headers.

texjake · 03-02-2014, 01:36 AM

I repainted my dash bezel today. I used Rust-Oleum black hammered paint & I used silver metallic enamel for the outside trim. I used a silver metallic Sharpie to outline the letters with.

BugzC10 · 03-02-2014, 08:35 AM

Quote:

Originally Posted by Mike_The_Grad

Ready to be put back into service...but, I had a smidgen of forethought as far as spark plug wiring is concerned. Im looking for a "clean" appearance. Considering i just painted the engine and frame. I have hedman long tube headers, already piped to fit, and it seems I have a routing issue with #5 & #6 plugs. the primary tubes from #1 & #2 run so close to the plugs that the wire looms I have won't allow the boot (taylor cut to fit red wires with 90° boot) any clearance at all, were talking 1/8" max. I can only imagine doing this if it was in the truck! So I'm faced with a dilemma. I have a lot of "bling" on top, and I just picked up the wires. I would really like to show off both. Different headers are not out of the question, nor is different wiring, considering I haven't cut any wires yet. Any input is well received!...

Looks like you need to switch to the "shortie" spark plugs, then take a look if you need to have some of the boots be 45 deg or straight. In addition maybe add some of the boot insulators. They protect the boots, but may not show off the wires like you want. Or change your headers.

stepsider · 03-02-2014, 11:29 AM

What is a shortie spark plug ?

**Boog** · 03-02-2014, 12:12 PM

They are spark plugs that are shorter in overal length to give more room between the header tube and the spark plug for the wires.
I searched Summit and found these right away.
http://www.summitracing.com/parts/acc-0576s-4/overview/

Lou Boffa · 03-02-2014, 12:15 PM

the straight boots let you control the "curve" some. I was surprised that once set up, the wires stayed where I formed them over time. Mine is w manifolds as opposed to headers but the principal is the same.

**Mike_The_Grad** · 03-02-2014, 01:23 PM

TeX Jake that dash bezel looks awesome. Just gave me an idea for a project during the week...

texjake · 03-02-2014, 03:03 PM

Quote:

Originally Posted by Mike_The_Grad

TeX Jake that dash bezel looks awesome. Just gave me an idea for a project during the week...

Thanks man! Just a warning, when I went to use the Dupli-color prep-spray before painting it, it removed all the existing factory black from the bezel. That was ok because I was going to re-paint it anyways. I was just not expecting it to remove the factory black paint that fast or that easy. I used 400 grit sandpaper on the edges to remove the old silver paint and of course the prep cleaner removed the black paint for me. I also used the Dupli-Color® Adhesion Promoter before painting it. That Rust-Oleum black hammered paint was great for the bezel because it adds to that textured look that the bezel has on it. And a good prep job is most important for a long lasting paint job. I painted the edges first & let them dry good before masking them off before painting on the black. And the silver metallic Sharpie really was impressive to use to outline the letters, IMO they almost look like the factory did em'.

**Mike_The_Grad** · 03-02-2014, 05:31 PM

Thanx for the heads up. TeX Jake. I'll keep that in mind.

C10Calvin · 03-02-2014, 06:00 PM

Boom! Took my steering column apart today. Going to rebuild it hopefully it goes back together ok. This was in the bed of the truck when I bought it. It was all rusted and froze up. I'm not sure what year the steering column is, they guy I bought the truck from just threw it in because the truck has a trans am tilt column in it and I didn't like it. Is there any way to tell what year the column is?

72CampSpecial · 03-02-2014, 07:40 PM

Finally installed shoulder belts in the truck... after multiple attempts I'm finally satisfied with how they are installed. Also installed a new winder regulator..can finally roll down the window again!

ChrisWhewell · 03-02-2014, 07:58 PM

MSD 8653 distributor on my 350 !!

colgad · 03-02-2014, 08:01 PM

Finally on the last leg of painting the 67. Got the bed assembled this week and Painted today!!!

Only the hood is left.

colgad · 03-05-2014, 12:01 AM

Wood installed today
Chrome wheel housing - Purchased from Southern Kentucky Classics
http://sokyclassics.com/product.php?skcid=1002476

magwakeenercew2jh · 03-05-2014, 12:12 AM

Quote:

Originally Posted by colgad

Wood installed today

Where'd ya get the tubs?

Willys47 · 03-05-2014, 02:03 AM

took a 2 tailgates dented smashed up tail gates and made one just for me

Aussie Ol' Blue · 03-05-2014, 03:56 AM

Found some repro mirror heads for a 69 Holden. Took the crappy sports mirror off the arms and installed the new bits. Not super flash and eventually want to get the squarish mirrors on the longer 66 style arms. The original mirrors were useless inasmuch as I couldn't get enough angle on the right hand side and when your driving on the wrong side of the truck on the right side of the road (being the left) you wanna know who you're about to cut off!

BugzC10 · 03-05-2014, 07:24 AM

Quote:

Originally Posted by colgad

Wood installed today

Bed looks terrific..inside and out!

**DaHos** · 03-05-2014, 07:52 AM

Checked a few more items off the list.

Picked up some goodies from being powder coated. Also got the ft and rear bumpers done !

74baggedbug · 03-05-2014, 09:03 AM

[/URL]
Full comp cam valve train installed..

02-28-2014, 01:37 PM	#276
Fitz Account Suspended Join Date: Jan 2007 Location: Tucson Posts: 2,183	Re: What did you do to your truck today? Chapter II Fabricated and installed a polished stainless steel radiator cover. Attached Images

02-28-2014, 02:08 PM	#277
67Slider Registered User Join Date: Mar 2010 Location: Pueblo West, CO Posts: 944	Re: What did you do to your truck today? Chapter II Looks good Fitz! How long did it take you? __________________ 67 C10 Stepside 66 Mustang Coupe 99 Burb 2500

03-01-2014, 08:29 AM	#279
Mike_The_Grad Senior Member Join Date: Oct 2013 Location: Santa Paula, CA Posts: 580	Re: What did you do to your truck today? Chapter II Ready to be put back into service...but, I had a smidgen of forethought as far as spark plug wiring is concerned. Im looking for a "clean" appearance. Considering i just painted the engine and frame. I have hedman long tube headers, already piped to fit, and it seems I have a routing issue with #5 & #6 plugs. the primary tubes from #1 & #2 run so close to the plugs that the wire looms I have won't allow the boot (taylor cut to fit red wires with 90° boot) any clearance at all, were talking 1/8" max. I can only imagine doing this if it was in the truck! So I'm faced with a dilemma. I have a lot of "bling" on top, and I just picked up the wires. I would really like to show off both. Different headers are not out of the question, nor is different wiring, considering I haven't cut any wires yet. Any input is well received!... Attached Images __________________ 1972 C/10 LWB - Mine 1964 C/10 LWB - My Dad's Instagram: Mike_The_Grad Last edited by Mike_The_Grad; 03-01-2014 at 08:32 AM. Reason: amendment

03-01-2014, 09:56 AM	#280
Fitz Account Suspended Join Date: Jan 2007 Location: Tucson Posts: 2,183	Re: What did you do to your truck today? Chapter II I avoided that problem with my headers by using 45 degree plug boots and the GM wire looms. Should work on yours too. Attached Images

03-01-2014, 01:44 PM	#281
Mike_The_Grad Senior Member Join Date: Oct 2013 Location: Santa Paula, CA Posts: 580	Re: What did you do to your truck today? Chapter II Thanx Fitz. I thought of 45° boots also.But I think I have a solution.I'm gonna try header wrap and just go a little beyond the boots. Plus side is I won't have to wire wheel and paint the headers. __________________ 1972 C/10 LWB - Mine 1964 C/10 LWB - My Dad's Instagram: Mike_The_Grad

03-02-2014, 01:36 AM	#282
texjake Registered User Join Date: Nov 2013 Location: Lubbock, TX Posts: 283	Re: What did you do to your truck today? Chapter II I repainted my dash bezel today. I used Rust-Oleum black hammered paint & I used silver metallic enamel for the outside trim. I used a silver metallic Sharpie to outline the letters with. Attached Images __________________ "Now all I need is a shop to go with my shop vac!"

03-02-2014, 11:29 AM	#284
stepsider Registered User Join Date: Nov 2013 Location: Roseville, CA Posts: 207	Re: What did you do to your truck today? Chapter II What is a shortie spark plug ?

03-02-2014, 12:12 PM	#285
Boog laying low Join Date: Mar 2001 Location: Searcy, Ark. USA Posts: 12,946	Re: What did you do to your truck today? Chapter II They are spark plugs that are shorter in overal length to give more room between the header tube and the spark plug for the wires. I searched Summit and found these right away. http://www.summitracing.com/parts/acc-0576s-4/overview/ __________________ Boog 69 Chevy stepside, 358/T350, 4.11 posi, 4.5/4 drop, rallys, poboy driver primer is finer 91 Chevy sportside, Tahoe, Yukon & GMC Crewcab All GM..'nuff said. I stand for the flag and kneel at the cross

03-02-2014, 12:15 PM	#286
Lou Boffa Registered User Join Date: Jan 2013 Location: San Antonio, TX Posts: 733	Re: What did you do to your truck today? Chapter II the straight boots let you control the "curve" some. I was surprised that once set up, the wires stayed where I formed them over time. Mine is w manifolds as opposed to headers but the principal is the same. Attached Images __________________ Figure out what you want--then figure out what you are willing to give up to get it.

03-02-2014, 01:23 PM	#287
Mike_The_Grad Senior Member Join Date: Oct 2013 Location: Santa Paula, CA Posts: 580	Re: What did you do to your truck today? Chapter II TeX Jake that dash bezel looks awesome. Just gave me an idea for a project during the week... __________________ 1972 C/10 LWB - Mine 1964 C/10 LWB - My Dad's Instagram: Mike_The_Grad

03-02-2014, 05:31 PM	#289
Mike_The_Grad Senior Member Join Date: Oct 2013 Location: Santa Paula, CA Posts: 580	Re: What did you do to your truck today? Chapter II Thanx for the heads up. TeX Jake. I'll keep that in mind. __________________ 1972 C/10 LWB - Mine 1964 C/10 LWB - My Dad's Instagram: Mike_The_Grad

03-02-2014, 06:00 PM	#290
C10Calvin Registered User Join Date: Dec 2013 Location: Cape Girardeau, Mo. Posts: 27	Re: What did you do to your truck today? Chapter II Boom! Took my steering column apart today. Going to rebuild it hopefully it goes back together ok. This was in the bed of the truck when I bought it. It was all rusted and froze up. I'm not sure what year the steering column is, they guy I bought the truck from just threw it in because the truck has a trans am tilt column in it and I didn't like it. Is there any way to tell what year the column is? Attached Images

03-02-2014, 07:40 PM	#291
72CampSpecial Registered User Join Date: Nov 2012 Location: Tacoma, WA Posts: 133	Re: What did you do to your truck today? Chapter II Finally installed shoulder belts in the truck... after multiple attempts I'm finally satisfied with how they are installed. Also installed a new winder regulator..can finally roll down the window again!

03-02-2014, 07:58 PM	#292
ChrisWhewell Registered User Join Date: Mar 2012 Location: Georgetown, Texas Posts: 73	Re: What did you do to your truck today? Chapter II MSD 8653 distributor on my 350 !! __________________ '67 K-20 longbed 4X4, 350, SM-420, Vortec heads, flat top 4-brow pistons, Eaton 4.55's, Qjet, MSD 8365, Comp XE250H, Dynomax duals

03-02-2014, 08:01 PM	#293
colgad Registered User Join Date: Jun 2006 Location: Lutz, Florida Posts: 838	Re: What did you do to your truck today? Chapter II Finally on the last leg of painting the 67. Got the bed assembled this week and Painted today!!! Only the hood is left. Attached Images __________________ 1967 Red, C10 Short Bed 6.0L T5 5 speed 1967 Orange and Black C50 6.2 Detroit Diesel NV4500, 2 Ton Pickup 1972 White, Chevy Blazer 2WD 67 Dog house 5.3 4L65 2016 Power Tour LH 1955 Red-Cream, Chevrolet Nomad, restoration on hold 2004 Black, Corvette Z06 LS6 convertible (Rock solid Fun) 2011/2018 Power Tour



Register or Log In To remove these advertisements.

03-05-2014, 12:01 AM	#294
colgad Registered User Join Date: Jun 2006 Location: Lutz, Florida Posts: 838	Re: What did you do to your truck today? Chapter II Wood installed today Chrome wheel housing - Purchased from Southern Kentucky Classics http://sokyclassics.com/product.php?skcid=1002476 Attached Images __________________ 1967 Red, C10 Short Bed 6.0L T5 5 speed 1967 Orange and Black C50 6.2 Detroit Diesel NV4500, 2 Ton Pickup 1972 White, Chevy Blazer 2WD 67 Dog house 5.3 4L65 2016 Power Tour LH 1955 Red-Cream, Chevrolet Nomad, restoration on hold 2004 Black, Corvette Z06 LS6 convertible (Rock solid Fun) 2011/2018 Power Tour Last edited by colgad; 03-08-2014 at 12:56 AM. Reason: Added link to Chrome Wheel Housing

03-05-2014, 02:03 AM	#296
Willys47 Registered User Join Date: Dec 2007 Location: Nanaimo B.C. Posts: 604	Re: What did you do to your truck today? Chapter II took a 2 tailgates dented smashed up tail gates and made one just for me Attached Images __________________ I was hooked on these trucks since 1982 when I drove my budys fathers 1968 Custum GMC 396 automatic dana 60 rear with a power lock diff what a ride more fun then we will we can ever tell!!

03-05-2014, 03:56 AM	#297
Aussie Ol' Blue Registered User Join Date: Sep 2013 Location: Sassafras. Victoria. The beautiful Mount Dandenong Ranges Posts: 234	Re: What did you do to your truck today? Chapter II Found some repro mirror heads for a 69 Holden. Took the crappy sports mirror off the arms and installed the new bits. Not super flash and eventually want to get the squarish mirrors on the longer 66 style arms. The original mirrors were useless inasmuch as I couldn't get enough angle on the right hand side and when your driving on the wrong side of the truck on the right side of the road (being the left) you wanna know who you're about to cut off! Attached Images __________________ CLASSIC 1970 C20 WITH A RUMBLIN' V8. IT'S MY MID-LIFE CRISIS ONLY IT AIN'T A LITTLE RED SPORTS CAR OR A HARLEY! IF YOU'RE GUNNA SKATE ON THIN ICE, YOU MAY AS WELL TAP DANCE!

03-05-2014, 07:52 AM	#299
DaHos Senior Member Join Date: Sep 2011 Location: Owosso, Michigan Posts: 2,853	Re: What did you do to your truck today? Chapter II Checked a few more items off the list. Picked up some goodies from being powder coated. Also got the ft and rear bumpers done ! Attached Images __________________ 1967 C10 SWB Owner - Rustbelt Restorations

03-05-2014, 09:03 AM	#300
74baggedbug Registered User Join Date: Oct 2011 Location: Houston tx Posts: 699	Re: What did you do to your truck today? Chapter II [/URL] Full comp cam valve train installed..

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register or Log In To remove these advertisements.