The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 03-20-2002, 07:57 AM   #1
70chevy
Registered User
 
70chevy's Avatar
 
Join Date: Aug 2001
Location: Cherryville, NC
Posts: 147
Post Need help....

I am going to install disc brakes up front. Will be using 2" drop spindles for 73 yr. model. Will the lower ball joints need to be for the year model of the spindles or the model of the truck it is going on and 1" or 1 1/4" rotor.
Any suggestions on where to buy parts needed.

Thanks in advance,

Ken
1970 1/2ton SWB
__________________
Ken Smith
99 C5 Torch Red Coupe
85 Chevy Candy Apple

70 Chevy 1/2 in process.Semi-gloss black powdercoated frame & suspension, disc brakes up front, 3" drop spindle(Beltech) 5 lug 3.73 rearend, ZZ4, Sanderson headers, 700R4, Air Ride system, Summitt 16 gal fuel cell, Holly mech. fuel pump,
70chevy is offline   Reply With Quote
Old 03-20-2002, 08:07 AM   #2
71GMCstreet
Registered User
 
Join Date: Dec 2001
Posts: 97
Post

Okay, I did the EXACT setup on my 71. Here goes.....yes the upper and lower joints will fit the 73 drop spindle. You will have to replace both tie rod ends as they are shorter and thicker than the 71/72 stuff. If you don't change to the 1 1/4" rotor, be prepared to put in a pair of wheel spacers to get the tie-rod to inside wheel end clearances. I'm pretty sure if you change to the 1 1/4" rotors, you MAY need oto change to calipers. I've been on spacers and haven't had any problems. Hope this helps.
71GMCstreet is offline   Reply With Quote
Old 03-20-2002, 08:09 AM   #3
71GMCstreet
Registered User
 
Join Date: Dec 2001
Posts: 97
Post

Edit change 2.......you MAY need to change THE calipers......
71GMCstreet is offline   Reply With Quote
Old 03-20-2002, 10:26 AM   #4
69 longhorn
Registered User
 
Join Date: Aug 2001
Location: rock island,il,usa
Posts: 5,382
Post

you need to order the balljoints & tie rods for the year of the spindle.....the upper ball joint is different from 72 to 73,also I think the outer tie rod end is different(on the taper). Also going from a 70,you may need to change center link & tierod assemblies(inner/outer/sleeve).....69 longhorn.

[This message has been edited by 69 longhorn (edited March 20, 2002).]
__________________
http://community.webshots.com/user/hotrodhorn
69 longhorn is offline   Reply With Quote
Old 03-20-2002, 02:43 PM   #5
70chevy
Registered User
 
70chevy's Avatar
 
Join Date: Aug 2001
Location: Cherryville, NC
Posts: 147
Post

So if I understand correctly I will need a
1 1/4" Rotor. The spindles are different according to the rotor thickness, right?
Buy upper and lower ball joints for the yr. spindle.

Ken
__________________
Ken Smith
99 C5 Torch Red Coupe
85 Chevy Candy Apple

70 Chevy 1/2 in process.Semi-gloss black powdercoated frame & suspension, disc brakes up front, 3" drop spindle(Beltech) 5 lug 3.73 rearend, ZZ4, Sanderson headers, 700R4, Air Ride system, Summitt 16 gal fuel cell, Holly mech. fuel pump,
70chevy is offline   Reply With Quote
Old 03-20-2002, 02:53 PM   #6
71GMCstreet
Registered User
 
Join Date: Dec 2001
Posts: 97
Post

My mistake, sorry, I did'nt read the truck is a 70, I am running the 1" rotor on the 73 spindle, the diameter on the spindle is the same for both. The ball joints upper and lower will need 73 and up stuff, don't want to take ya down the wrong path...thanks longhorn..
71GMCstreet is offline   Reply With Quote
Old 03-20-2002, 03:10 PM   #7
69 longhorn
Registered User
 
Join Date: Aug 2001
Location: rock island,il,usa
Posts: 5,382
Post

Im not sure on the cut off date,but i think the 1" rotors were used on some apps 80 & up. Most of the older stuff that i have been into has had the heavy rotors. i have seen that job done several ways,but the easiest....)if you dont have spindles already),may be to pick up a set to bolt in for your app. I converted my 69 several yrs ago,when there werent many parts available. You will find that the lower a arms have a different steering stop,& will shorten the steerin radius(i used 71-72 lower arms),& have 75 spindles(cut coil drop). I set it up to use a bell Tech spindle(73 up was available).......talking with bell tech,they said use the ball joints,& outer tie rod for the 73 -79 spindle. There have also been some differences noted in the center link,so if you go for 71-79, you should be ok there. lenghts are also different on tie rods & sleeves.....so i can see why some guys are swappin a complete crossmember(all the parts are off 1 truck). Here is a link to spindles for your app..... http://www.classicperform.com/discdrop.htm
__________________
http://community.webshots.com/user/hotrodhorn
69 longhorn is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:22 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com