How many leaves should I run in 56" springs? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

fun in dirt · 02-14-2011, 01:25 PM

This set of 56" I was planning on using for rear of my Blazer has 9 leaves - 8 regular & 1 overload I think. They're out from under a single wheel 1ton CUCV. So I'm sure they're pretty stiff as is. I'm gonna take them apart & clean/paint them anyway, so which leaves & how many should I take out for a better ride?

fun in dirt · 02-15-2011, 02:56 PM

Okay I'll try saying it another way...
Let me see some pics of other folk's 56" springs; how many leaves are in them?

drunkbus · 02-15-2011, 03:06 PM

Here's what I have. It looks like there are 8 in mine. These are out of a 3/4 ton.

fun in dirt · 02-17-2011, 11:27 AM

Quote:

Originally Posted by drunkbus

Here's what I have. It looks like there are 8 in mine. These are out of a 3/4 ton.

How rough is the ride? I don't mind & do like it a little stiff but not too rough.

drunkbus · 02-17-2011, 01:43 PM

Quote:

Originally Posted by fun in dirt

How rough is the ride? I don't mind & do like it a little stiff but not too rough.

Compared to what? The only thing I have to compare it to was the 40 year old stock warn out suspension that was pretty rough as it was. Any lifted vehicle is going to be a little stiff but I don't think this setup is bad at all. I would think it would have to be a better ride than using 6" lift springs in the rear and personally I would never use blocks so this was my choice.

WHITE-NOISE · 02-26-2011, 12:06 PM

i went with 56 inch springs off a cucv truck for my 68. the spring center pin isnt the same as the factory spring so i had to run the springs backwards and use an 1.5 zerorate block from diy4x4 to move the axle forward, but its still a half an inch back from factory spec, but i doubt anyone will even notice it. i used the rear hangers and shackles from the same truck. over all it ended up giving me a little more than 4inches of lift in the rear. as for the ride of it, i have no idea yet as im not done building the truck :waah

cucv springs (top) and stock 68 spring (bottom)

after i finished up getting everything measured out and bolted up.

i took the top overload spring and spacer block out and left everything else on, theres 9 leafs left in the pack.

gave it some army green accents to set it off

02-14-2011, 01:25 PM	#1
fun in dirt Registered User Join Date: Jan 2007 Location: Mississippi Posts: 2,118	How many leaves should I run in 56" springs? This set of 56" I was planning on using for rear of my Blazer has 9 leaves - 8 regular & 1 overload I think. They're out from under a single wheel 1ton CUCV. So I'm sure they're pretty stiff as is. I'm gonna take them apart & clean/paint them anyway, so which leaves & how many should I take out for a better ride? Attached Images __________________ '72 C to K20 "Cannibalizer" http://67-72chevytrucks.com/vboard/s...32#post8653432 '85 K30 "Big Nassy" '06 3500 Duramax ...tow truck '06 Silverado SS...DD '06 C1500 WT...DD '07 Classic C1500 WT...DD Built & sold cause can't keep 'em all: '72 Blazer "The Bucket" http://67-72chevytrucks.com/vboard/s...d.php?t=433190 '55 Chevy straight axle gasser https://www.trifive.com/forums/showthread.php?t=173938 '69 Pro Street Chevelle http://www.chevelles.com/forums/showthread.php?t=332541 '86 M1031 CUCV http://67-72chevytrucks.com/vboard/s...d.php?t=553619

02-15-2011, 02:56 PM	#2
fun in dirt Registered User Join Date: Jan 2007 Location: Mississippi Posts: 2,118	Re: How many leaves should I run in 56" springs? Okay I'll try saying it another way... Let me see some pics of other folk's 56" springs; how many leaves are in them? __________________ '72 C to K20 "Cannibalizer" http://67-72chevytrucks.com/vboard/s...32#post8653432 '85 K30 "Big Nassy" '06 3500 Duramax ...tow truck '06 Silverado SS...DD '06 C1500 WT...DD '07 Classic C1500 WT...DD Built & sold cause can't keep 'em all: '72 Blazer "The Bucket" http://67-72chevytrucks.com/vboard/s...d.php?t=433190 '55 Chevy straight axle gasser https://www.trifive.com/forums/showthread.php?t=173938 '69 Pro Street Chevelle http://www.chevelles.com/forums/showthread.php?t=332541 '86 M1031 CUCV http://67-72chevytrucks.com/vboard/s...d.php?t=553619

02-15-2011, 03:06 PM	#3
drunkbus New Member Join Date: Jun 2007 Location: Coos Bay, OR Posts: 1,077	Re: How many leaves should I run in 56" springs? Here's what I have. It looks like there are 8 in mine. These are out of a 3/4 ton. Attached Images

02-26-2011, 12:06 PM	#6
WHITE-NOISE Registered User Join Date: Jul 2010 Location: waynesville, ohio Posts: 67	Re: How many leaves should I run in 56" springs? i went with 56 inch springs off a cucv truck for my 68. the spring center pin isnt the same as the factory spring so i had to run the springs backwards and use an 1.5 zerorate block from diy4x4 to move the axle forward, but its still a half an inch back from factory spec, but i doubt anyone will even notice it. i used the rear hangers and shackles from the same truck. over all it ended up giving me a little more than 4inches of lift in the rear. as for the ride of it, i have no idea yet as im not done building the truck :waah cucv springs (top) and stock 68 spring (bottom) after i finished up getting everything measured out and bolted up. i took the top overload spring and spacer block out and left everything else on, theres 9 leafs left in the pack. gave it some army green accents to set it off



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.