|
06-12-2018, 06:27 PM
|
#1 |
|
Registered User
 
Join Date: Apr 2010
Location: Louisiana
Posts: 970
|
Is this a Dana 44?
Wasn’t sure where to ask this question but the rear end is suppose to be out of a 1988 one time chevy. I thought it should’ve been a 14 bolt but nope. Thanks for any info anyone can provide.
Wade |
|
|
|
06-12-2018, 06:47 PM
|
#2 |
|
Registered User
Join Date: Jan 2016
Location: Barber City, CA
Posts: 4,728
|
Re: Is this a Dana 44?
I posted some measurements and an ID chart in this thread..
http://www.67-72chevytrucks.com/vboa...60#post8262848 good luck!
__________________
I started out with nothing - and I still have most of it |
|
|
|
|
06-12-2018, 09:15 PM
|
#3 |
|
Registered User
Join Date: Apr 2010
Location: Louisiana
Posts: 970
|
Re: Is this a Dana 44?
Thank you for the info. It looks like this one is stamped “70 HD” on the front top passenger side. Measurements are in keeping with the chart of roughly 12” high and 11” wide on the differential cover.
Wade |
|
|
|
|
06-12-2018, 09:42 PM
|
#4 |
|
Registered User
Join Date: Apr 2010
Location: Louisiana
Posts: 970
|
Re: Is this a Dana 44?
It does have 9/16” wheel studs
Wade |
|
|
|
|
06-13-2018, 08:29 AM
|
#5 |
|
Registered User
Join Date: Jun 2012
Location: cibolo tx
Posts: 1,033
|
Re: Is this a Dana 44?
The picture is upside down and a little close up to really tell but it appears to be a 70hd.
It will have 4" axle tube diameter and be 77" wide.
__________________
1985 k5 396/nv4500/203/205 d60/d70 4.56 42 sx2 1991 V3500 350/4l80/205 60/14 4.10 35 toyos. |
|
|
|
|
06-13-2018, 12:20 PM
|
#6 |
|
Senior Member
Join Date: Mar 2003
Location: Colfax-California
Posts: 8,390
|
Re: Is this a Dana 44?
4'' tubes for sure, but not all of them were that wide, there are some single wheel 70hds than come in around 68ish
|
|
|
|
|
06-13-2018, 04:27 PM
|
#7 |
|
Registered User
Join Date: Apr 2010
Location: Louisiana
Posts: 970
|
Re: Is this a Dana 44?
I’ll measure it when I get home. I was told it was 1988 chevy one ton and it’s a dually rear
Thanks, Wade |
|
|
|
|
06-13-2018, 04:29 PM
|
#8 |
|
Registered User
Join Date: Jun 2012
Location: cibolo tx
Posts: 1,033
|
Re: Is this a Dana 44?
Square body 88 will be 77" where new body 88 is narrower.
__________________
1985 k5 396/nv4500/203/205 d60/d70 4.56 42 sx2 1991 V3500 350/4l80/205 60/14 4.10 35 toyos. |
|
|
|
|
06-13-2018, 05:17 PM
|
#9 |
|
Registered User
Join Date: Jan 2016
Location: Barber City, CA
Posts: 4,728
|
Re: Is this a Dana 44?
D70 HD
 If you don't mind me saying, nice rearend 
__________________
I started out with nothing - and I still have most of it |
|
|
|
|
06-13-2018, 07:27 PM
|
#10 |
|
Registered User
Join Date: Apr 2010
Location: Louisiana
Posts: 970
|
Re: Is this a Dana 44?
I don’t mind you saying. LOL! 😂. It’s a thick rear end for sure
Wade |
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
