The 1947 - Present Chevrolet & GMC Truck Message Board Network

Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board


Thread Tools Display Modes
Old 10-12-2017, 12:02 PM   #1
Registered User
Join Date: Oct 2017
Location: Green Ridge, Missouri
Posts: 1
Drum Brake Problems

I have a 1969 C-20 Longhorn with manual drum brakes and recently the pedal became very hard & had little to no travel. The brakes will not lock up and when you give the pedal all you can, fluid forces out the master cylinder cap.

I have replaced the proportioning valve and the short lines from the master, along with the front rubber lines and the rear rubber line. All 4 drums have been turned and new shoes have been installed. One wheel cylinder was leaking, so it was replaced. The system was bled and the problem still exists.

I'm thinking it must be the master cylinder as the lines flowed when we bled the system and didn't appear to be blocked.

Anyone have any thought on what this problem may be?
Wlee56 is offline   Reply With Quote
Old 10-12-2017, 05:39 PM   #2
Registered User
custom10nut's Avatar
Join Date: Apr 2015
Location: Columbia SC (temp) East Tn (soon)
Posts: 1,085
Re: Drum Brake Problems

You're on the right track. I would say something corroded. Master Cylinders are not expensive, and since you replaced everything else, do that too.
custom10nut is offline   Reply With Quote
Old 10-13-2017, 12:04 AM   #3
Registered User
saxart's Avatar
Join Date: Aug 2012
Location: St. Croix River Valley, WI
Posts: 557
Re: Drum Brake Problems

I'd say you have some wheel cylinders that are rusting on the inside. Mine exhibited the same symptoms, then started to leak so I replaced what looked like new cylinders. I pulled them apart once the job was done to see what was going on inside, and they were coated in a crystal rust. Locked them up tight!

If it were my truck, I'd replace the 3 remaining wheel cylinders. They're not bad in cost, just not fun to replace.
Meet "Old Roy":
saxart is offline   Reply With Quote
Old 10-13-2017, 04:41 AM   #4
Senior Member
Ironangel's Avatar
Join Date: Feb 2010
Location: Falls City,Nebraska
Posts: 1,513
Re: Drum Brake Problems

I agree with replacing the master cylinder "and" the three remaining wheel cylinders...Be ready to replace some brake lines as well, "Kroil" is your friend on those rusted fittings...
Michael Hill, "Ghostrider"
1980 KZ-1000 ST-MKII, "Baby Doll"
72 Chevy C/10 SS-396 w/Comp Cam=268H, Closed Chamber 290 heads, Stage-4 Power Pack (Eagle Red's) 350THM, Beefed up 12-Bolt, Eaton 4:56 Posi, (Diesel Killer) Street Rod LWB "Nasty Sally"
72 Chevy C/10 Rebuilt 350 w/Voodoo-10120701 Cam, Stage-4 350THM, Beefed up 12-Bolt 3:73 Eaton Posi, LWB Wood Bed, (Daily driver, work horse) "Belle"
Ironangel is offline   Reply With Quote


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT -4. The time now is 04:43 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2018, vBulletin Solutions Inc.
Copyright 1997-2013