The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1960 - 1966 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 02-21-2018, 02:06 PM   #1
lukespence
Registered User
 
Join Date: Feb 2018
Location: Austin
Posts: 4
350 swap help

Hey,

I am new to the whole 63 c-10 modding stuff and need some help. Recently bought a 63 chevy with a 283 in it and a 4 speed. We took out the old 283 and dropped in a 350. The 350 was out of a 68. so the engine mounts worked fine. the only problem is that with the engine bolted in there is still a gap between the bell housing and then block. whats up with that?


Thanks Luke
lukespence is offline   Reply With Quote
Old 02-21-2018, 03:01 PM   #2
Clyde65
1965 Chevy C10, 2005 4.8L/4l60
 
Clyde65's Avatar
 
Join Date: Aug 2004
Location: DFW Texas
Posts: 8,539
Re: 350 swap help

Is the converter seated properly?

Tried loosening motor mount bolts and perch bolts, then tighten the trans bolts?
__________________
Clyde65

Rebuild of Clyde
http://67-72chevytrucks.com/vboard/s...84#post8338184

69 Aristocrat Lo Liner build
http://67-72chevytrucks.com/vboard/s...84#post7561684



support our troops!
Clyde65 is offline   Reply With Quote
Old 02-21-2018, 03:40 PM   #3
shortstep60
Registered User
 
Join Date: Nov 2013
Location: Mayetta, Kansas
Posts: 439
Re: 350 swap help

Get under your truck and see if you can move the tork converter. If you cant move the tork converter you don't have it all the way back in the trans.
shortstep60 is offline   Reply With Quote
Old 02-21-2018, 03:51 PM   #4
The Rocknrod
Moderator

 
The Rocknrod's Avatar
 
Join Date: Aug 2011
Location: China Spring, TX
Posts: 7,280
Re: 350 swap help

If the torque converter is attached to the flywheel then to the crank . . .
As was said already - the torque converter is probably not seated correctly.
The Rocknrod is offline   Reply With Quote
Old 02-21-2018, 04:11 PM   #5
geezer#99
Registered User
 
geezer#99's Avatar
 
Join Date: Aug 2009
Location: Bowser
Posts: 13,495
Re: 350 swap help

Where did you guys read anything about an automatic tranny swap?
I read that he still has the 4 speed.
That needs to be clarified!
Then we can answer his question.
If he still has the 4 speed it’s likely the input shaft isn’t seated into the pilot bearing.
geezer#99 is offline   Reply With Quote
Old 02-21-2018, 04:19 PM   #6
The Rocknrod
Moderator

 
The Rocknrod's Avatar
 
Join Date: Aug 2011
Location: China Spring, TX
Posts: 7,280
Re: 350 swap help

It's not my fault, I drink in the morning. Everybody knows that.
The Rocknrod is offline   Reply With Quote
Old 02-21-2018, 04:34 PM   #7
geezer#99
Registered User
 
geezer#99's Avatar
 
Join Date: Aug 2009
Location: Bowser
Posts: 13,495
Re: 350 swap help

Quote:
Originally Posted by The Rocknrod View Post
It's not my fault, I drink in the morning. Everybody knows that.
But it’s afternoon and evening somewhere too!
I know that quandry.
So much beer, so little time!
geezer#99 is offline   Reply With Quote
Old 02-21-2018, 05:16 PM   #8
The Rocknrod
Moderator

 
The Rocknrod's Avatar
 
Join Date: Aug 2011
Location: China Spring, TX
Posts: 7,280
Re: 350 swap help

Quote:
Originally Posted by geezer#99 View Post
But it’s afternoon and evening somewhere too!
I know that quandry.
So much beer, so little time!
Doc wont let me have beer anymore I'm too sweet if you know what I mean. But that Jack Daniels Green Label Mmm, Mmm, Mmmmm
The Rocknrod is offline   Reply With Quote
Old 02-21-2018, 05:28 PM   #9
lukespence
Registered User
 
Join Date: Feb 2018
Location: Austin
Posts: 4
Re: 350 swap help

yes it is a manual 4 speed. used a clutch alignment tool beforehand. the engine is bolted up to the frame. so it should work. I think I just realized the problem. the flywheel on the engine is from when it had a t5 connected to it. is that the problem is that different.
lukespence is offline   Reply With Quote
Old 02-21-2018, 06:37 PM   #10
geezer#99
Registered User
 
geezer#99's Avatar
 
Join Date: Aug 2009
Location: Bowser
Posts: 13,495
Re: 350 swap help

Shouldn’t matter.
Should slide right in.
You might need to reverse the process.
Bolt the bell to the motor and then slide the tranny in place.
Or hook up your clutch linkage so someone can depress the clutch to release the disc and let the tranny slide in.
geezer#99 is offline   Reply With Quote
Old 02-22-2018, 03:40 PM   #11
61K10
Registered User
 
61K10's Avatar
 
Join Date: Feb 2012
Location: pleasant valley--placerville ca
Posts: 3,039
Re: 350 swap help

he said the engine is bolted to the mounts. bellhousing bolted down? Mounts in the forward holes?
__________________
1961 chevy K10

my build is------------61K10 build
61K10 is offline   Reply With Quote
Old 02-22-2018, 05:47 PM   #12
Wrenchbender Ret
Registered User
 
Join Date: Oct 2005
Location: Overland Park, Ks.
Posts: 5,190
Re: 350 swap help

Some bell housings are for a 10 in. clutch. If you put a flywheel & 11 or 12 in clutch in it won't clear & leaves a gap.
Wrenchbender Ret is offline   Reply With Quote
Old 02-26-2018, 08:19 PM   #13
rvrfoot
Registered User
 
Join Date: Oct 2016
Location: san bernardino ca
Posts: 1,611
Re: 350 swap help

Quote:
Originally Posted by Clyde65 View Post
Is the converter seated properly?

Tried loosening motor mount bolts and perch bolts, then tighten the trans bolts?
They just read the 350 and thought it was a 350 thans.
rvrfoot is offline   Reply With Quote
Reply

Bookmarks

Tags
1963, 350 sbc, chevy

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 04:54 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com