Pics of how to route and fasten lines to frame? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**Slowguy** · 01-18-2019, 09:49 PM

I can't figure out the best method of routing the lines and making them pretty. It would be nice if there was a "modular" tubing clamp so that you could set up the clips along the frame rail and choose which size to install in which spot. Leading to the rear I'll have 3/8" air tubing, stainless brake line, fuel supply and return lines, and of course the wires for the rear tail lights. Either I don't know the terminology to search for, or nothing exists (...and I don't believe that would be possible).

It would be nice to see how others have routed their lines to keep everything tidy, secure, and cosmetically pleasing.

**clay68c10** · 01-18-2019, 10:02 PM

I'm planning on using these clamps for all my lines
https://www.amazon.com/Rubber-Cushio...SXEHCXPS08NVHK

**kwmech** · 01-18-2019, 10:04 PM

Ford trucks have what you may be looking for. Plastic holders that will retain (I think) 3-4 lines or a harness

**Slowguy** · 01-18-2019, 10:56 PM

Quote:

Originally Posted by clay68c10

I'm planning on using these clamps for all my lines
https://www.amazon.com/Rubber-Cushio...SXEHCXPS08NVHK

Thanks for the link. Yes, those will work great. I’d prefer a clamp that will hold multiple line to lessen the amount of fastening points but if I can think find anything like that I’ll purchase that exact kit you referenced.

Have you decided on the method to fasten those? I don’t want to use screws because I’d have sharp points pok8ng out everywhere. That leaves a bunch of short stainless nuts and bolts. If that’s what’s necessary then that’s what I’ll do but it will require lots of drilling and lots of nut/bolt work.

Metaldoc · 01-20-2019, 01:35 AM

10 24 machine screws with nyloc nuts all SS. Put some white grease between the rubber and lines to stop rust. Split loom with SS trailer wire clips on the opposite side

**clay68c10** · 01-20-2019, 10:45 AM

I was planning something just like Metaldoc. Clean, simple, and affordable.

**1971Stepside** · 01-20-2019, 11:08 AM

These are what I’m using on my build. Very good product. Can get them at Summit

https://www.notchead.com/line-clamps.html

SJLenz1340 · 01-20-2019, 11:19 AM

LMC sells the Notchead fastening system now. I just received an email from them probably yesterday about this specifically.

**MJN** · 01-20-2019, 02:20 PM

Made4You Products makes similar clamps and kits. I've used them in the past with good luck and they're made in the USA. You can order them direct or through Summit.

https://www.made4youproducts.com/chazisclamp

**zicc1835** · 01-20-2019, 03:32 PM

subd

FL71C10 · 01-20-2019, 08:35 PM

I use those same rubber insulated fuel line clamps. I just used one hole and I had one going in each Direction so that you could hold two lines with one bolt.

FL71C10 · 01-20-2019, 08:38 PM

Here is a better picture of two lines running parallel to each other

Metaldoc · 01-20-2019, 09:35 PM

Quote:

Originally Posted by FL71C10

I use those same rubber insulated fuel line clamps. I just used one hole and I had one going in each Direction so that you could hold two lines with one bolt.

Should never run fuel and electrical together. If the electrical shorts you got a big fire.

Jeff's72C10* · 01-21-2019, 10:08 AM

Quote:

Originally Posted by FL71C10

Here is a better picture of two lines running parallel to each other

That's exactly how we secure wire and tubing runs on airplanes.

James K · 01-22-2019, 11:10 AM

Quote:

Originally Posted by 1971Stepside

These are what I’m using on my build. Very good product. Can get them at Summit

https://www.notchead.com/line-clamps.html

Great product, easy to use.

88Stanger · 01-22-2019, 04:17 PM

Quote:

Originally Posted by FL71C10

Here is a better picture of two lines running parallel to each other

This is how I did mine also.

01-18-2019, 09:49 PM	#1
Slowguy Senior Member Join Date: Aug 2017 Location: Chicago,il Posts: 356	Pics of how to route and fasten lines to frame? I can't figure out the best method of routing the lines and making them pretty. It would be nice if there was a "modular" tubing clamp so that you could set up the clips along the frame rail and choose which size to install in which spot. Leading to the rear I'll have 3/8" air tubing, stainless brake line, fuel supply and return lines, and of course the wires for the rear tail lights. Either I don't know the terminology to search for, or nothing exists (...and I don't believe that would be possible). It would be nice to see how others have routed their lines to keep everything tidy, secure, and cosmetically pleasing.

01-18-2019, 10:02 PM	#2
clay68c10 Senior Member Join Date: Aug 2004 Location: Centennial, CO Posts: 2,883	Re: Pics of how to route and fasten lines to frame? I'm planning on using these clamps for all my lines https://www.amazon.com/Rubber-Cushio...SXEHCXPS08NVHK __________________ ClusterTruck: 68 C10 Bought in 89, wrecked in 03. Slow low $ rebuild started '17. 6.0 & TKO http://67-72chevytrucks.com/vboard/s...d.php?t=788602 93 K1500 Short Step, 350, NV4500, EBL flash ECU. Vortec heads & roller cam someday... 05 Jeep Wrangler Unlimited. 3” lift & 6-speed 02 E320 the insurance total “free car” 13 Tahoe LTZ

01-18-2019, 10:04 PM	#3
kwmech Senior Member Join Date: Mar 2003 Location: Colfax-California Posts: 8,382	Re: Pics of how to route and fasten lines to frame? Ford trucks have what you may be looking for. Plastic holders that will retain (I think) 3-4 lines or a harness

01-20-2019, 01:35 AM	#5
Metaldoc Registered User Join Date: Apr 2015 Location: Ayr Ontario Posts: 1,122	Re: Pics of how to route and fasten lines to frame? 10 24 machine screws with nyloc nuts all SS. Put some white grease between the rubber and lines to stop rust. Split loom with SS trailer wire clips on the opposite side Attached Images __________________ Do it, Do it right, Do it right the first time Last edited by Metaldoc; 01-20-2019 at 01:42 AM.

01-20-2019, 10:45 AM	#6
clay68c10 Senior Member Join Date: Aug 2004 Location: Centennial, CO Posts: 2,883	Re: Pics of how to route and fasten lines to frame? I was planning something just like Metaldoc. Clean, simple, and affordable. __________________ ClusterTruck: 68 C10 Bought in 89, wrecked in 03. Slow low $ rebuild started '17. 6.0 & TKO http://67-72chevytrucks.com/vboard/s...d.php?t=788602 93 K1500 Short Step, 350, NV4500, EBL flash ECU. Vortec heads & roller cam someday... 05 Jeep Wrangler Unlimited. 3” lift & 6-speed 02 E320 the insurance total “free car” 13 Tahoe LTZ

01-20-2019, 11:08 AM	#7
1971Stepside Almost Satisfied Join Date: Mar 2002 Location: Springfield, MO Posts: 2,928	Re: Pics of how to route and fasten lines to frame? These are what I’m using on my build. Very good product. Can get them at Summit https://www.notchead.com/line-clamps.html __________________ 1971 C10 Stepside. LSx 6.0 with BTR Stage IV, Speed Engineering Headers, 4L80e transmission w/3200 Circle-D Stall. 3.73. Posi. Purchased this truck when I was 17. I started the rebuild (or take apart) in 1993. I have drug it around all over the country in pieces. Finally back on the road in 2021. "I can't complain, but sometimes I still do. Life's been good to me so far."

01-20-2019, 11:19 AM	#8
SJLenz1340 Registered User Join Date: Jun 2014 Location: Ingleside, IL Posts: 56	Re: Pics of how to route and fasten lines to frame? LMC sells the Notchead fastening system now. I just received an email from them probably yesterday about this specifically. __________________ Regards Steve

01-20-2019, 02:20 PM	#9
MJN Registered User Join Date: Feb 2000 Location: Maquoketa, Ia/ Orr, Mn Posts: 2,957	Re: Pics of how to route and fasten lines to frame? Made4You Products makes similar clamps and kits. I've used them in the past with good luck and they're made in the USA. You can order them direct or through Summit. https://www.made4youproducts.com/chazisclamp __________________ '51 South Bend Model "9A" '56 Chevy 3600 NAPCO '74 Chevy Cheyenne Super K20-restored on 37's '72 GMC Sierra Custom K2500- in progress '08 GMC Envoy Denali '12 GMC Sierra 2500HD Denali '17 GMC Yukon XL VCCA member #58596 http://www.nohrco.com

01-20-2019, 03:32 PM	#10
zicc1835 Senior Member Join Date: Mar 2011 Location: Hanover NJ Posts: 4,104	Re: Pics of how to route and fasten lines to frame? subd __________________ Doc & Kim build http://67-72chevytrucks.com/vboard/s...d.php?t=722288 I am from the desert http://67-72chevytrucks.com/vboard/s...d.php?t=650332 basket case build SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=648557

01-20-2019, 08:35 PM	#11
FL71C10 Registered User Join Date: Jun 2010 Location: Orlando, Florida Posts: 2,506	Re: Pics of how to route and fasten lines to frame? I use those same rubber insulated fuel line clamps. I just used one hole and I had one going in each Direction so that you could hold two lines with one bolt. Attached Images __________________ 71 Chevy C10 Shortbed Stepside. LT1 with 4l60E. Just got back from painter, in assembly now.

01-20-2019, 08:38 PM	#12
FL71C10 Registered User Join Date: Jun 2010 Location: Orlando, Florida Posts: 2,506	Re: Pics of how to route and fasten lines to frame? Here is a better picture of two lines running parallel to each other Attached Images __________________ 71 Chevy C10 Shortbed Stepside. LT1 with 4l60E. Just got back from painter, in assembly now.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.